Search Documents

By Michael Amick

Due to the importance of maintaining open airways on a longwall panel, mine management decided to install cribs made of foamed cement. Foamed cement had been used at other company operations on several projects. A recent test at a sister operation had proven the crib installation technique and established that foamed cement cribs could provide better support than wooden cribs. The area to be supported was in a remote location; the limited material needs of foamed cement cribs offered a substantial advantage. In mid February 1993, 75 foamed cement cribs were installed on the tailgate of the active longwall panel. The 75 cribs resisted both horizontal and vertical stresses while successfully supporting the entry.

Jan 1, 1993

By C. H. Larsen

The results of a comprehensive investigation of conveyance arrestment devices (safety catches) in United States coal mines are presented. Availability and use, performance, inspection, maintenance, testing, procedures, and regulatory requirements were investigated. Information was obtained from equipment manufacturers, mine operators, and regulatory-agency personnel, as well as from studies of domestic and foreign mining safety regulations. Traditional mine hoists and commercial elevators for mine use were investigated. Results of this and an earlier study of wire-rope practice in United States coal mines show a continued need for conveyance arrestment devices. A wide variety of these devices are in use. Only two types have been proved reliable for stopping a conveyance without injuring passengers or equipment. These are elevator overspeed-actuated wedge-clamp (Type B) safeties and broken-rope-actuated devices for wooden guides using a single-tooth-dog design developed in Ontario as a braking element. Elevators are widely used in U. S. coal mines. When maintained according to American National Standards Institute (ANSI) Specifications A17. I and A17. 2, they appear to present no major arrestment problems. Of 42 coal-mine hoists used for man transport that were inspected, 30 are in vertical and 12 in inclined shafts. Twenty-four vertical shafts use wood guides; 6 use steel. The 12 inclined-shaft systems use flanged-wheel T-rail guidance. Two wood-guided vertical-shaft systems use the single-tooth Ontario-type dog; the other 22 use multi-toothed wedges, cams, or dogs that have been proved highly unreliable. The arrestment devices in the six steel-guided vertical-shaft systems and in six of the inclined-shaft systems cannot be evaluated because performance data are lacking. The remaining six inclined-shaft systems have no arrestment devices at all. Of the 36 hoists with arrestment devices, the devices of 16 are never tested, the devices of 10 are actuated periodically with the conveyance at rest, and the devices of the other 10 are actuated periodically with a slow-moving conveyance. Although high speed is as probable as low speed in an emergency and would provide the best test of arrestment capability, no tests are performed in the United States which demonstrate the ability of an arrestment device to stop a loaded conveyance from high speed. Mine operators indicate little confidence in their conveyance arrestment devices, and manufacturers recognize a need to improve their products. Neither state nor Federal regulations provide a guide to this improvement. Mine operators, manufacturers, and state and Federal regulatory agency personnel would welcome specific guidance. In view of this, a set of application, design, actuation, stopping-performance, and testing and inspection criteria is presented as a guide to eliminating the inadequacies of these devices. Recommendations are included for improving hoist controls and machinery directly affecting conveyance safety.

Jan 1, 1972

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By AIME AIME

WAR undoubtedly accelerates metallurgical progress, although its most obvious effect is a tremendous waste of materials. The necessity for restrictions in normal uses of metals results in a search for substitutes or for enhanced properties that will make a limited supply last longer. An insatiable demand for more metal to be produced more quickly favors trial of new processes, new metallurgical tools, and new methods of fabrication. Greatest advance is made, of course, in practical physical and process metallurgy. Theoretical or fundamental research necessarily must take a secondary position, and is so regarded in this review. It is not that developments in theoretical physical metallurgy are lacking entirely, but, following the same trend noted in other countries as they entered war activities, attention in the U.S.A. has been shifted strongly to those developments having an immediate practical application.

Jan 1, 1943

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner&apos;s representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

By J. E. Cleveland

The major health concern for uranium miners is the release of radon gas and the resultant ingrowth of the short lived daughters in the mine atmosphere. Present methods of control are the utilization of mine ventilation systems for dilution and control of ingrowth time to maintain working levels below those set by regulations. This study examined pressure cycling efforts on the radon emanation. The mechanical ventilation systems were altered to allow pressure changes throughout the mine to increase radon influx during the off shifts and thus deplete the sources of radon gas. Continuous radon working level and environmental monitors, developed by the Bureau of Mines, were employed to monitor radiation and physical parameters in the mine workings. The mine ventilation system was then varied to induce radon flows during off shifts, thus, depleting the radon sources during normal production shifts. Electro-static precipitators were also tested to determine radon daughter collection efficiencies. Both radon and radon daughter concentrations were monitored and evaluated. Major problems were found in the simple mechanical operation of cleaning these units.

Jan 1, 1982

By R. HOLROYD

The Ludwigshafen and Oppau plants are largely independent I. G. factories situated some 23 miles apart on the west bank of the Rhine facing lannheim. The former factory is a general organic chemical works specializing in dyes, dye intermediates, plastics and synthetic rubber,. while the latter is a heavy organic chemical factory producing ammonia, methanol, higher alcohols and their derivatives. Before the war much of the I. G. research and development work was carried out at Ludwigs- hafen; in particular the high pressure research section directed by Dr. Mathias Pier played a very active part in all hydrogenation developments. Apart from the possibility that a full scale hydrogenation or Fischer Tropsch plant had been erected at Ludwigshafen/Oppau during the war, the main objectives of an oil team investigation were: - (a) To obtain from Dr. Pier and his staff an advance general picture of German fuel production processes. (b) To study the fuel developments still in the research and pilot plant stage. (c) To examine any new developments in hydrogen or synthesis gas manufacture. (d) To look for new processes for production of high anti-knock fuel constituents and for new fuel additives. (e) To investigate new chemical syntheses based on raw materials obtainable from oil. The Ludwigshafen and Oppau factories were first visited by the large team listed in Appendix A during the period 25-31st March. The investigation revealed that no large plant for synthetic fuels or lubricants had been operated at this target. All the important members of the Fuel Research Section staff had been evacuated to Heidelberg and information on the work of this department was therefore limited to that contained in seized documents, the greater part of which have still to be examined in detail. Valuable information on synthesis gas production from hydrocarbon gases was obtained as well as interesting data on a num- ber of chemical syntheses. Two members of the above team Holroyd and Faragher accompan- ied by Major Tilley (interrogator) went on to Heidelberg, contacted Dr. Pier and the chief members of his staff on April 1st and obtained from them the hydrogenation information given later in the body of the report. Later, after visiting Leuna, Holroyd, Faragher and Ellis paid a second visit to Heidelberg and to Ludwigshafen/Oppau on 27th-30th May to check a number of details, particularly with respect to hydrogenation costs, and to obtain information on the pressure.conversion of water gas to hydrogen and on the manufacture of Wickel pressure vessels.

Aug 1, 1943

By Euclid P. Worden

INTRODUCTION Today, conventional raise boring is an accepted method of development in underground mines and on major construction projects. Over the years that this technique, and its associated machines and tools, have been under development, many articles have been written on the subject. To a great extent, these papers have reported operating results of one or more specific projects or have been generalized reviews of state-of-the-art machines and tools. This paper is intended as a review of the technique from an operational standpoint. Conventional raise boring, as opposed to the related variants box hole drilling and underground blast hole drilling, is a two step process consisting of the pilot hole drilling and reaming cycles. This author has covered the subject of pilot hole drilling in another article (1) . A good review of the current machines and equipment has been presented by Monroe (2) and an overall review of this entire technology was published by E&MJ (3) and Mining Journal, April, 1983 (4) . The subject of the reaming cycle is presented here together with some of the technical aspects of how the drilling tools are intended to be used. OPERATIONS Bit Change After the pilot bit has broken through at the end of the pilot hole cycle, a changeover takes place at both the machine and

Jan 1, 1985

By Albert L. Toenges

The production of bituminous coal by stripping methods has become an important factor in some areas, especially in the Central and South Central States. In the latter, production at strip mines exceeds that at deep mines. Table 1 shows the tonnage produced at strip mines and the percentage of the total production for 1924 to 1935, inclusive, for the States in which the mines described in this circular are situated.4/ Following are references to earlier Bureau of Mines publications on strip mining of bituminous coal: Cash, F. E., and von Bernewitz, M. W., Methods, Costs, and. Safety in, Stripping and Mining Coal, Copper Ore, Iron Ore, Bauxite, and Pebble Phosphate: Bull. 298, Bureau of Mines, 1929, 275 pp. Kiessling, O. E., Tryon, F. G., and Mann, L., The Economics of Strip-Coal Mining: Econ. Paper 11, Bureau of Mines, 1931, 32 pp. Turner, Scott, and Bureau of Mines Staff; Mining Bituminous Coal by Stripping Methods: Inf. Circ. 6383, Bureau of Mines, 1930, 23, pp.

Jan 1, 1937

By Karl J. C. Harries

"12.1. NO DEPRECIATION/GAAPAll calculations and computations relating to the Royalty shall be carried out in accordance with generally accepted accounting principles consistently applied to the extent that such principles are not inconsistent with the provisions of this Schedule and the agreement attached hereto, it being specifically agreed that nothing herein contained shall permit, or be construed to permit, the Operator to deduct any amount for depletion, depreciation, amortization or any deduction that represents a non-cash outlay.Comment: In cases like net profit royalties where recoupment of prior expenditures is permitted, care should be taken to avoid any implication that depreciation may also be taken. It is only logical and equitable that Property Owners should not be permitted an apparent ability to “double dip” with respect to deductions. A provision like this example should accomplish the task. It will be noted that the example specifically contemplates that the negotiated arrangements will prevail over any requirements of GAAP. Accordingly, if the parties agree to an unusual formula for recoupment, it will not be set aside to accommodate GAAP requirements. Under GAAP, revenues and expenditures are accounted for on an accrual basis. In addition, it specifically prohibits the taking of non-cash deductions, which is in keeping with the concept of recoupment.Although in some ways the example states the obvious and could be considered redundant, its presence, especially in provisions contemplating recoupment, makes it clear to the financial people that there may well be some variations from normal practices dictated by GAAP, while at the same time confirming the availability of GAAP to fill any voids.The accounting profession often makes the caveat that application of GAAP is an “art”, not a “science”. GAAP do not provide a cure-all and can create problems that will have to be addressed. For example, GAAP contemplate that asset costs are to be reduced by investment tax credits, which can cause a problem for a payor with more than one mine."

Jan 1, 2003

By R. D. Brown

"AbstractIn order to raise the enormous amounts of capital which will be essential for the development of Canada's mineral and petroleum resources, this country's resource industry must be permitted to earn an acceptable rate of return. The existing tax regime, with its high rates, complexities and misdirected incentives, presents a serious obstacle to our resource industries in their development of Canada's immense , but increasingly lean, resources. Government tax and other policies are not the only cause of the crisis now facing the resource sector in Canada, but a reformed tax system, with stable and reasonable tax burdens, is required if Canada's resources of minerals, oil and natural gas are to continue to contribute in the future, as in the past, to our national well-being.An independent task force, organized under the auspices of the Canada West Foundation, has recently completed a wide -ranging report: on the future development of Canada's mineral, oil and gas resources. This five-volume report, completed after almost two years of research and study, concludes that Canada •is facing a major crisis •in the development of our resources, It states that unless corrective action is taken now, mineral production and exports could decline drastically after 1985, at the same time that Canada would face massive bills for imported oil because of inadequate and declining production.The task force, chaired by the author of this article, has put forward recommendations for a fundamental shift in both federal and provincial policies in order that Canada's mineral reserves can be developed in the national interest. This article consists of excerpts from the summary of the task force's report."

Jan 1, 1977

By M Pyle, R Ch, G Lane, ramhan

Data is the most valuable commodity in the information age. The use of data enables productivity, opportunity, and safety in various sectors and industries. In the late 1950s, Alan Turing coined the term artificial intelligence (AI) to describe the ability of computing machines to think and behave like humans through simplified reasoning and logic (Turing, 1950). This concept of mimicking human behaviour is the building block of machine learning algorithms used in most AI software. The ‘learning’ aspect in machine learning requires data, that is, information on the environment or the objective, to be modelled or predicted using AI. An AI-enabled system aims to predict the unknown faster and intuitively. Intuition in software algorithms can be described as probabilistic, learned through the data that the AI system is trained on; indeed, the AI software cannot predict the future, but it can provide the likelihood of an event/action occurring, thereby enabling decisions or responses to prevent it or take action. Just as various industries have adopted AI as the tool of choice to seek new opportunities (examples: medical research, self-driving cars, financial modelling), the mining industry, too, has been receptive to embracing AI for problem-solving and maximising the value of its business.

Sep 1, 2024

By C. Richard Tinsley

INTRODUCTION The economic analysis (Chapter 3), the engineering studies (Chapter 10), the credit structure (and the consequential funding sources) - Chapter 11, and the overall feasibility structure for any venture are all directed to determining one major decision element: How much and how certain is the reward for taking these risks? Risk assessment is a surprisingly weak area of analysis and is usually addressed in a checklist fashion. It is much preferable to deal within a risk system so that the inevitable tradeoffs among risks are correctly made. DEFINITION The first step toward risk definition must be to ascertain all of the risks to which a project or a company is exposed; otherwise one will remain ignorant of the possibility of a financially crippling loss until it occurs. (Carter and Crockford, 1974). However, simply stating what "risk" is can lead to debate. For example, risk could be (adapted from Vaughan, 1982): -the chance of a loss - uncertainty of loss -possibility of loss - uncertainty -dispersion of actual from expected results - probability of an outcome different from the one expected - possibility of an occurrence of an undesirable contingency -a condition in which a possibility of a loss exists. For the minerals industry financier, the last definition is probably the most appropriate. However, from a mineral company&apos;s point of view the definition might well include the possibility of not achieving the expected financial return. RISK CLASSIFICATION Risk identification will be readily agreed as the all-important first step. There are five major "branches" of risk classification. These are: -Statistical -Modellers -Checklist -Project Financing -Insurance The Statistical set discovered probability theory and any risk discussion soon deteriorates into a mathematical jungle (Megill, 1977; Hartman, 1976; Reutlinger, 1970; and Pouliquen, 1970).Their use of terminology tells its own story: coin toss (binomial distribution), gamblers&apos; ruin, delphi (oracle) techniques, monte-carlo simulations, random walks, etcetera. These techniques inadequately represent the judgements necessary in an increasingly complicated and interrelated world. The risk Modellers have turned to the computer to handle these inter-relationships but soon find barriers because of "simultaneity". Certainly the computer has its uses to conduct various analyses (marketed as "sensitivity" analyses) but very often one finds that this involves changing one or two variables at a time, all other things being equal. Unfortunately, in a modern and complex world all other things do not remain equal. The statisticians will, no doubt, jump to their own defence by citing this

Jan 1, 1985

By G. P. Halliwell, C. R. Austin

The investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at t,he Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word &apos;&apos;Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 per cent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy," or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limitJ&apos; has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend test developed by Howard Scott.&apos; In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1932