Search Documents

By Mark C. L. Patterson

Hydrothermal brines are extracted from significant depths below the surface of the earth and arrive at the surface at elevated pressure and temperature. The exact chemistry and conditions of these brines depends upon the rock formations through which the water travels, but many of the brines are rich in dissolved minerals especially silica which is often saturated in the brine. At pressure and temperature the minerals remain in solution but in order to extract heat from the brines, they need to be cooled and during which many of the minerals precipitate causing problems. Where precipitation is a problem in the downstream processing, the brines are maintained at a high enough temperature and pressure so as to avoid precipitation and injected back into the geothermal formation. This results in a significant loss in potential energy that could be recovered from the geothermal brines. If left to precipitate in an uncontrolled manner, many of the minerals will precipitate as gels, in a high surface area form which is difficult to extract from the liquor and which can causes problems. Precipitation in this manner often builds up on the inside of pipes, reducing the pipe cross-section available for fluid flow and reducing the overall efficiency of the plant. If the brines are seeded at the appropriate time or the precipitation conditions are changed, mineral particles can be grown and separated more easily from the brine. During this precipitation and growth phase the chemistry of the local environment can also be altered to grow more valuable particulates. Some of the specific chemistries will be discussed with reference to known geothermal brines and what needs to be done to precipitate value added products. A theoretical approach to the complete extraction of minerals from geothermal brines is also discussed with the goal of extracting more heat from the brine prior to reinjection into the well.

Jan 1, 2006

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

The Research on Application of New Technologies in High Gradient Magnetic Separator with Horizontal Magnetic Line

Sep 13, 2010

By K. J. Stanaway

Major world ilmenite and rutile accumulations reveal similar regional geology and Proterozoic age deeper crustal source rocks. During crustal collision titanium crystallizes as ilmenite and rutile at buried sites of high pressure and temperature rock metamorphism. Hydrothermal activity can convert titanium minerals to rutile, but titanium migration and enrichment seem only local. Many melts crystallize rocks with iron-titanium oxides in solid solution, but titanium enrichment at economic scale takes place in basic intrusive melts often associated with anorthosites and charnokite. Sedimentary placer enrichments have formed since the Proterozoic with water-resistant ilmenite, and rutile segregating by gravity from quartz sands deposited from flowing water. Placers have residual, alluvial, strand and shallow marine variants. Time, organic acids, and sand permeability play lead roles in the leaching of iron from ilmenite during weathering and diagenesis.

Jan 1, 2005

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By D. R. Shoemaker, H. W. Judges

A 16.5-kt/d underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp Inc., a wholly-owned subsidiary of Union Oil Company of California. The new $200-million underground project will revitalize mining and milling activity at Questa, where small scale underground mining first began in 1920. Large scale open-pit mining was initiated in 1965 but now, because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first produc¬tion is scheduled for early 1983. The company expects full capacity-9 Gg of molybdenum per year-to be reached in 1984.

Jan 6, 1980

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Italy is one of the major producers of ceramics in the world. Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and “granitic” sands. These rocks contain other minerals, such as quartz, plagioclase and mafic minerals, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse grind size.This paper reports a study conducted on the separation of K-feldspar from quartz, plagioclase and biotite, from a feed of ground granite. The feasibility of the separation using a dynamic dense medium separation system has been investigated, as an alternative to the traditional flotation technique. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency. Tests were conducted on two samples of crushed granite having size distributions of –3 +1 mm and –1 +0.5 mm.Heavy liquid analysis was performed on the two samples. As the rheological properties of the dense medium interact with the separation efficiency, the stability and viscosity of the dense medium were controlled and kept within an appropriate range; which was achieved with the addition of an artificial contaminant (clay) to the dense medium."

Jan 1, 2003

By Emad Farouz

The resistance of very dense glacial outwash formations consisting of sand, gravel and cobble formations can be quite high, and techniques for measuring the strength and deformation properties often cause engineers to underestimate the strength of these layers in drilled shaft design. More realistic measurements of this dense formation can be achieved with slotted steel casing pressuremeter tests. To minimize disturbance and achieve accurate measurements, drilling a pilot hole prior to probe insertion is necessary. Characterizing geologic formations that contain significant amounts of gravel and cobbles is challenging because of scale factor. Inserting a standard pressuremeter probe into this formation without damaging the membrane is difficult. This paper presents a case study for the IR-75 project in Dayton, Ohio, USA, where these dense materials were characterized using a slotted casing pressuremeter, optimizing design by providing more realistic properties of these materials.

Jan 1, 2006

By A Hoyle, P Walker, D Bennett

The Phu Kham copper-gold operation located in Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited, based in Brisbane Australia, holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining 10 per cent held by the Government of Laos PDR.The 12Mt/y copper-gold concentrator at Phu Kham commenced production in April 2008. Flotation copper and gold recovery from commissioning was consistently poor, due to the high levels of pyrite and problematic secondary and oxide copper species and non-sulfide gangue.The low recoveries of copper and gold from Phu Kham were recognised during the feasibility study design phase. A bulk sulfide flotation regime in roughing produced high recoveries, however a large capacity cleaning circuit was required and there was risk of not meeting saleable concentrate grade specifications. The installed design offered a capital efficient compromise to ensure that a concentrate grade of 24% copper could be achieved at acceptable recoveries.Incremental improvements in copper recovery were achieved by 2011 through conversion of conditioning cells to flotation cells in both roughing and first cleaning and increased cleaner capacity through the installation of a Jameson cell. In 2012 the Phu Kham Upgrade Project was commissioned to increase mill throughput, along with additional rougher and cleaner capacity to increase residence times at the nominal 16 Mt/y throughput. The marginal reduction in primary grind size due to the additional ball milling power also provided a small recovery improvement.This paper presents the development, design, implementation, and performance of the Increased Recovery Project commissioned in April 2013 which targeted the major causes of copper loss from the circuit. Based on fundamental and detailed test work and mineralogical analysis of concentrator streams, an optimised design was developed which has increased copper and gold recoveries by over 5% and 10% respectively. The Increased Recovery Project has positioned the concentrator to process high pyrite ores that were previously considered untreatable, and opened further opportunities for maximising flotation recovery by de-bottlenecking plant regrind and cleaning capacity.CITATION:Hoyle, A, Bennett, D and Walker, P, 2015. The increased recovery project at the Phu Kham copper-gold operation, Laos PDR, in Proceedings MetPlant 2015, pp 246–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

By Colin C. West

On August 7, 1986, Barge 45, while being towed near the mouth of the Niagara River, was swept downstream and pinned against one of the central piers of the Peace Bridge. The barge rested against the pier with 125 feet overlying the Canadian border and 50 feet overlying the American border. The tug boat which was towing the barge was lost further downstream. Fortunately, the crew escaped and were rescued with no loss of life. There was serious concern about the potential erosion effects of the river currents on the foundation of the bridge pier as caused by the flow concentrations around the barge structure. Due to the time of year, with the approaching Fall and associated worsening weather conditions, it was imperative that the barge be removed as soon as possible. Donjon Marine of New Jersey, the United States Navy's Atlantic Zone Contractor, was called on to retrieve the barge. By this time the original owner had abandoned the wreck.

Jan 1, 1987

By Sun Chuanyao, Jia Muxin

Generally, if the bond valence (BV) between metal ion and oxygen of the mineral is greater than 0.8, only surface species –Me-O-H or –Me-O exposures on the mineral interface, if the BV is between 0.2-0.8, the metal ion exposures on the interface, and if the BV is less than 0.2 the metal ion dissolves into water. The PZCs of oxide minerals and island silicate minerals are determined by the bond valence of the bond in the mineral crystals, the higher the bond valence the lower the PZC of the mineral. So the PZC sequence of Al2SiO5 minerals is kyanite> andalusite> sillimanite. The general rule for framework silicate minerals is as: The higher the Al content, the lower the PZC of the mineral, when the ratio of Al to Si in the tetrahedron skeleton is below 1:3. The higher the Al content, the higher the PZC of the mineral, when the ratio of Al to Si in the skeleton is between 1:3 and 1:1. The general rule for layer silicate minerals is summarized as: the three-layer silicate minerals have much lower PZCs than that of the two-layer silicate minerals. The threelayer silicate mineral with the octahedron layer occupied by lower charged cations has lower PZC than that of the three-layer silicate mineral with the octahedron layer occupied by higher charged cations. The twolayer silicate mineral with the octahedron layer occupied by lower charged cations has higher PZC than that of the two-layer silicate mineral with the octahedron layer occupied by higher charged cations. The layer silicate mineral with Al substitution in the tetrahedron layer has lower PZC than that of the layer silicate mineral without Al substitution in the tetrahedron layer. Such pyroxene minerals whose M1 is occupied by a trivalence cation and the M2 is occupied by a monovalence cation has lower PZCs than those both M1 and M2 are all occupied by bivalence cations. Such hornblende minerals whose M2 is occupied by a trivalence cation and the M4 is occupied by a monovalence cation has lower PZCs than those both M2 and M4 are all occupied by bivalence cations. There is no Si4+ or 4 coordinated Al3+ exposures on the surface of framework silicate minerals, the metal ions of three layer or chain silicate minerals are compact between tetrahedron layersor chains, they hinder the metal ions to interact with oleate acid radical, the metal ion octahedron layer exposures on the surface of a two layer silicate mineral, but the the oleate acid radical can not attach to a metal ion by replacing a –OH- that connects three metal cations in the same time, So the floatability of such silicate mineral is bad. The metal octahedron chain style of an island silicate mineral affects it floatability, the mineral exposures octahedron chain metals with two dangling bonds in two directions floats better than the mineral exposures octahedron chain metals with two dangling bonds in one direction.

Jan 1, 2003

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

In the last two years the Commission for the Environment has received four Environmental Impact Reports (EIR) for Audit and has been or is involved with at least four environmental impact assessments (EIA) related to mining. The EIRs have included Weavers Coal Mine, the Monowai-Maratoto mining proposal, the Martha Hill mine and the Wainui Road Mill. The EIAs are related mainly to coal fields in the Waikato but also included a further EIA on Martha Hill.

Jan 1, 1986

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

On Feb. 16, 2012, the Polish coal mining company Lubelski Wegiel Bogdanka S.A. set the world record for daily production from a plow-equipped longwall, with an output of 24.4 kt (26,900 st) of coal from a single face. The company commissioned the first Cat longwall system at its Bogdanka Mine, near Lublin in eastern Poland, in March 2010 and within six months had raised the bar to nearly 17 kt/d (18,700 stpd) of cut coal. Since then, Bogdanka has continued to increase its daily output with a plow face that began mining in the new 7/VII/385 panel last October, taking the world record to new levels. In addition to the record output achievement, the plow face advanced more than 27 m (89 ft) at a 1.63-m- (5.3-ft-) cutting height. ?We thought this achievement would be impossible for any shearer in seam heights as low as this,? said Zbigniew Stopa, vice president of Bogdanka.

Jan 1, 2012

By P. Varona, L. Lorig, M. Board, E. Chacon

Geomechanical factors at the mine are important and will become even more relevant as the pit expands and deepens. To address these demands a team was assembled to collect geomechanical information and perform numerical analysis. The west wall is the largest and flattest of all the design sectors in the pit and rigorous studies were carried out on this wall. The wall behaviour is controlled mainly by a set of steeply dipping joints within the slope in the Fortuna Granodiorite and a weak zone, the Zona Plastica, that extends vertically near the pit bottom. These features lead to large toppling displacements in the upper portions of the wall. Two numerical models were used to reproduce the general features of failure observed in the wall. The modelling indicated that a toppling mode of failure results from shear on the steeply dipping joints. The toppling leads to slumping or landslides whereby the west wall flows slowly downslope as the Zona Plastica compresses

Apr 1, 1996

By Claude Cunningham

Ths oonoept of precise. eooursts timing with Elsotronic Delay Detonators (EDD’s) was first ssriously sddresssd in ths mid 80’s end much wss made of the cheapness end profusion of digital wstohes in terms of the likelihood of EDD’s also being cheap and essyto produce. Ten years Iater. with every major explosives group end many elsotronios groups having instituted projects to capitalize on the promise of these devices, production devices are still to come into asneral use.

Jan 1, 1994