Search Documents

The Waukon iron deposit comprises about 210 acres situated 2-1/2 miles north of Waukon, in Allamakee County, northeastern Iowa. The deposits have been exploited intermittently since 1899 and have produced about 67,000 tons of concentrated iron ore. From January to May 1943, the Bureau of Mines investigated the deposit to determine the extent of the ore-bearing material and its amenability to concentration, Seventy-one test pits were sunk. Those that indicated are of a grade high enough to warrant concentration tests were sampled. Average grade of ore was indicated to be 37.02 percent iron and 27.78 percent silica on a dry basis. Beneficiation tests indicated that the percentage of recovery might be relatively low.

Jan 1, 1949

There are circumstances where the ordinary techniques of experimental variography in geostatistics û now in common use despite their recent origin û are not quite successful. This paper describes a new addition to the geostatisticians tool kit developed by one of the renowned leaders in the field to cope specifically with these circumstances. Possible application of this technique will be outlined when it will be seen that there are still problems remaining to be solved in its use for economic evaluation of deposits with irregular mineralisation.

Jan 1, 1984

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount lVIorgan mine. It will be admitted that in all mining operation, the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be ineluded, as it is necessary to understand the eonditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan.

Jan 1, 1910

By Charles L. Kimbell

The year 1980 on the whole was not a good year for the world's mineral industry. The general upturn of activities in 1979 after a rather poor 1978 showing was not maintained with a number of key measurement standards showing downturns. Most notably, the world's steel and petroleum industries recorded significant reductions in output, the former in response to markedly lower demand levels and the latter partly in response to lower industrial consumption owing to general economic conditions and partly owing to successes in campaigns for the reduction of energy use in general and petroleum product use in particular among major importing nations that were feeling the trade balance pinch of ever-higher oil prices. During 1980, a number of political events-some international in scope, some confined to single nations-had significant influence upon world mineral industry activities and mineral commodity supplies, and other political happenings had the potential to significantly affect the industry in future times.

Jan 1, 1982

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By L. A. Cornish, L. H. Chown, M. Matema, R. Süss, L. Glaner, A. Douglas

Mintek has been developing Pt-based alloys for high temperature applications in aggressive environments, for example, land-based turbine engines, to replace the currently used nickel-based superalloys (NBSAs). The Pt-based alloys have a similar structure to the NBSAs, and since Pt is more chemically inert and has a higher melting point, the Pt-based alloys can potentially be used at higher temperatures. The greater chemical inertness of the Pt-based alloys compared to the NBSAs means that coatings can be simpler, or perhaps not even used at all, depending on the environment. TEM work was done at NIMS, Japan, to investigate the changes in the microstructure o f Pt-Al and Pt-Al-Ir alloys at elevated temperatures using in-situheating up to1100°C. Initial casting trials showed that work needs to be done to optimise casting parameters before commercialisation can take place. Room temperature tensile tests were performed and results were variable mainly due to microstructural differences. The alloy hardnesses were in the order of 300-350HV with ultimate tensile strengths of ~800 MPa and elongations of less than 10%. These results are comparable to other alloys used at high temperatures, which is very encouraging. Keywords: platinum, super alloys, hardness, tensile

Jan 1, 2006

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011

By Nicolae Dobritoiu

The literature in this field and the practical activity record that a method, respectively the technology used for an underground mining work have many components which, in order to be applied, demand that for each of the parameters that describe the environment of the mining work and that influence the chosing of that method and that technology of execution, must have values in an interval well determined. There are situations when one or many parameters of the set of parameters that describe the environment of the mining work, can modify its values, and, as a result, one or more components of the methods or technology cannot be applied anymore, making necessary a replacement of their values. The information offered by this graphical-analytical model allow the determination of optimum solutions for the process of digging of the underground mining work and thus it will result the incresing of the technical-economical efficiency of the digging process and, also the increasing of the quality of the underground mining work.

Oct 1, 2009

By James W. Martin

This user's manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By J. A. Hudson, D. L. Millar

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Rock engineering system performance monitoring using neural networks.) Synthetic and analytical approaches to objective-based design of rock engineering projects are discussed. Rock masses are considered as complex dynamic systems with components that concurrently interact with each other and their environment. The existence of a rock engineering system canon (i.e. a set of systems governing rules) is proposed. Its possible components are highlighted and an application is demonstrated using a "rock mass automaton" designed to simulate dynamic heat distribution in rock. In the example given, the canon implements the basic result from probability theory applied to the thermodynamics of solids. Rock engineering system performance is reduced to the mapping of the output of a rockmass to varying input (design) options, within the state space of the systems model. The Kohonen Self-Organising Map provides an extremely useful analytical tool to reduce the hyper-dimensionality of rock engineering system behaviour. Further, the hyper-dimensional state vector is mapped "quasiconformally" such that the neural map tends to spatially organise similar input state vectors, facilitating interpretation of rock engineering system behaviour (performance monitoring). Work is reported on the development and validation of the automation as a basis for an internal representation of the rock mass bahaviour. The results are reported of simulations compensating for the uncertainty of the exact mechanisms operating within the rock mass, using additive noise with the input state vector in the training stages of the self-organising map implementation. Initial work on adopting Grossberg's Adaptive Resonance Theory neural network architecture for classification of rock engineering systems behaviour is also presented

Apr 1, 1994

The importance of the Broken Hill mining field may be gauged from the fact that since the discovery of the ore-body in 1883, till the end of 1931, approximately 43,000,000 tons of ore have been raised.The lode covers a length of 31 miles, and in places is upwards of 300 ft. in width. The ore, as at present mined, consists of an intimately blended mixture of lead and zinc sulphides with silver and gangue minerals.Structurally the lode conveys the impression of a huge longitudinal arch (when viewed from the east or west), having its apex or crown near the centre of the field, in the leases of the Broken, Hill Proprietary Co. Ltd., where the lode outcropped at the surface.The minimum depth of the lode in the Proprietary mine was some 500 ft. from the surface, but huge undulations, having an average pitch of 45°, carry the extensions of the arch gradually deeper, to those places where active stoping operations are now in progress in the workings of the North mine at one extremity, and the South and Zinc Corporation mines at the other. The depth of the lode from the surface, as exposed at present, is approximately 1700 ft. at these extremities.The structure and physical character of the ore-body, and its containing walls, are so complex and varied that almost every type of mining problem is met with.

Jan 1, 1932

By Matteo Montesi

Deep foundation elements are often used as discrete elements in externally supported earth retaining structures such as soldier piles and lagging walls, secant/tangent pile walls, anchored walls, etc. These structures can be designed using different approaches such as conventional limit equilibrium methods, finite element/difference analyses, and soil spring (p-y) analyses which are contained in various commercially available computer programs used by engineers worldwide. Although these programs usually undergo various degree of verification and validation, users must be aware of each program’s limitations and conditions in which each design approach should or should not be used. These programs may incur difficulties when non-continuous deep foundation elements are used as part of the retaining system and in cases of non-uniform geometry where closed-form solutions are not available. Design input parameters such as passive arching width, wall-to-soil friction, and p-multipliers (pm) are not always given enough attention which may result in potential design deficiencies. This paper presents the main features of various earth retaining structure design approaches and discusses their advantages/disadvantages. The paper addresses some of the limitations and difficulties that may be faced with when utilizing non-continuous discrete deep foundation elements and identifies key elements that are sources of potential deficiencies and errors. An example comparing the design outcomes using different design approaches is presented. INTRODUCTION Earth retaining structures are used to retain soil and create or maintain a difference in ground elevation between grades in front and behind the retaining structure. Deep foundation elements have been used for decades to support earth retaining structures. Earth retaining structures that are supported by deep foundation elements are typically referred to as externally stabilized system (O’Rourke and Jones, 1990). An externally stabilized system uses an external structural element, in contrast to internally stabilized systems which rely on reinforcements installed within and extending beyond the potential failure mass. The design of externally supported retaining structures can be accomplished using different approaches, which can be challenging under certain conditions. Each approach has been discussed extensively in available literature, and is well summarized in the and Federal Highway Administration (FHWA) guidelines. The objective of this paper is to present the most widely used design approaches and discuss their limitations and difficulties in one concise and brief document, giving the reader a good source for comprehensive understanding of the various design approaches, supported by a technical example. This paper is not intended to be a comprehensive review of all available design methods and formulations available in the literature.

Jan 1, 2018

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defense, for purposes other than the: extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallics is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of they Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952