Search Documents

By J. Leinart

As is readily apparent, the reliability of the early-stage costs estimated for any mining project are critical to the viability of that project. An estimate too high might leave a potentially profitable deposit undeveloped or worse yet, available to a competitor. One too low might waste investment dollars in a project not yet economically ripe. There are two aspects critical to any estimate: 1. The cost data used to represent the values of the wages, salaries, supplies, and equipment. 2. The design used to determine the engineering parameters upon which the above estimated values are based. Given that all of the information contained in Mining Cost Service is provided by suppliers, equipment manufacturers and mine operators, one wonders why there is any question as to the reliability of cost estimates developed using this information. Given that it is all actual (as opposed to statistically derived) data, where do the problems with estimate reliability lie and what is the impact of the data on that reliability? The following presents a series of analyses designed to assess the reliability of the cost estimating process. Both the actual cost data and the engineering parameters upon which they are based are examined in an attempt to quantify and understand the importance of each. While several sources of cost information are available (Means, Richardson, Primedia?s Equipment Watch, and individual suppliers and manufacturers), the following rely solely on data contained in InfoMine USA, Inc?s, Mining Cost Service and in its Sherpa Mine Cost Estimating Software.

Feb 27, 2013

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Neil F. Archer

Due to the increased chance of violations and shutdowns by the U.S Occupational Safety and Health Administration(OSHA) and the U.S. Environmental Protection Agency (EPA), a company can save itself problems by taking control of the dust caused by conveying material. A complete dust-control policy can keep these emissions confined, sealed and suppressed, protecting the environment from fugitive, airborne dust. Material handling and processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need a dust control system.

Jan 1, 2003

By M. H. Solomon

After the global financial crisis of 2008, African mining is entering anew phase of development. The rapid withdrawal of emerging market funding from the critical exploration and development industries provided a hiatus in funding, a gap which was quickly filled by Chinese and other Asian investors. While the continent is still economically dependent on its extractive industries, the prevalence of Dutch Disease has undermined Africa?s ability to benefit fully from its mining, oil, and gas industries. While the extractive industries are closely related to many of the more fragile and failed states in Africa, it is equally true that the strongest states in Africa have mining-based economies. This paper explores the possible linkages between mining, strong and weak political economies, and poverty in Africa. It draws the conclusion that neither Dutch Disease nor Resource Course is a given in resource-endowed countries, and that it can be avoided if the mining economies in these countries are actively integrated into their respective broader economies and used to foster economic diversification. The author asserts that given the capacity constraints of many African governments, it is contingent on mining companies to become integrally involved in catalysing diversification around their infrastructure and supply chains.

Jan 1, 2011

The need for legislative reform of health and safety legislation has been recognised in New Zealand for about a decade. Previous legislation did not cover all work places, many areas were excluded from coverage, and there were at least 14 different acts and dozens of sets of regulations dealing with various aspects of health and safety.

Jan 1, 1993

THE art of mine surveying has made very great progress in recent years, and is still advancing, perhaps faster than any other branch of surveying. The scope of the mine surveyor's duties has greatly increased, his instruments and methods have improved, the responsibility of his position is greater, and the end is not yet in sight.It might be supposed that such a steadily growing subject would have an adequate literature, but this is by no means the case and outsiders commonly judge mine surveyors by their text-books. Hardly any condemnation can be too strong for most of these books. The English books truckle to the antiquated and crude methods apparently still in use in England, and thereby largely aid in perpetuating them; they commonly in illustrative examples give the distances in fathoms, feet, and inches; they spend page after page discoursing on instruments that should have been forgotten long ago; they try to antagonize theory and practice by detailing such calculations as that a certain vein will contain 2,003.907 pounds of galena per square fathom, and then reduce this amazing quantity to hundredweights, quarters, and pounds. Nothing can be more unscientific, or, for that matter, less businesslike, than unwarranted assumptions of accuracy; it is, perhaps, the greatest curse of applied science. Here we have a calculation to thethousandth part of a pound, when there is probably an unavoidable error of two hundred pounds. What shall we say of a man who explains how to measure the depths of shafts to the hundredth part of an inch by means of short brass rods screwed together...

Jan 1, 1909

By Chris Uys, Johan Labuschagne

Sishen Iron Ore Mine, located in the Northern Cape, is an open cast mine excavating approximately 100 million tons rock to produce 25 million tons of high grade haematite ore per annum. The size of the pit is approximately 12 km ‘1.5 km ‘150 metres. The final depth is planned to be around 350 metres. It is hard rock mining operation employing the conventional truck and shovel method. Mining benches are twelve and a half metres in height and are divided into blasting blocks, each consisting of approximately 300 000 tons of material.

Jan 1, 1997

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion. In several cases, breaches occurred between the gravel pit and the river. Initial evaluation of several sites that experienced these breaches showed that impacts to the river system were complex and varied significantly from site to site. The impacts to the adjacent river system may be viewed as positive and negative. Several flood-plain-mining sites in Oregon located in areas of historic river flow reverted to active riverbeds. In many cases, state and federal fisheries biologists and university researchers saw the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries —Mined Land Reclamation Program (DOGAMI-MLR) is studying the effects to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound flood-plain decisions regarding mining.

Jan 1, 1999

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By M. C. Bétournay

Hydrogen fuel cells are a known technology, having been applied to stationary (e.g. equipment, buildings, and power plants) and vehicle applications (e.g. transit buses and space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and greenhouse gas emissions. To date, however, fuel cells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuel cells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuel cell type of choice for the industry, the proton exchange membrane, would function at the range of surface operations, and use hydrogen that is stored under low pressure and risk. A small fuel cell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, Inco, the Ontario Ministry of Labour, Sandia National laboratories, and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter, as well as from shock and vibration provided to the unit in underground conditions at Inco?s 175 Orebody minesite and Stobie mine. The test results provided will show that the unit was not affected by the underground conditions; physically and electrically, the unit performed without any reduction in operation or adverse effects imposed

May 1, 2005

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

By M Dickie

During the 1980s and early 1990s low cost gold treatment plants were at the forefront of the Australian engineering and mineral processing business. This opportunity was the result of a high gold price and innovative design by emerging engineering companies in an expanding market. The low cost approach to gold plant design and project execution resulted in smaller and shorter life projects becoming viable and the multiplicity and fast track approach of the projects resulted in sharp learning curves. From the mid 1990s to the early 2000s the relatively low commodity prices and resultant reduction in minerals opportunities also resulted in innovative design in both small and large plants, albeit on a reduced scale. The innovation was associated with alleviating capital cost pressures for large capacity low-grade (eg NewcrestÆs Cadia) or small-scale (eg JubileeÆs Cosmos) projects to either improve NPV or to enable the project to be won and profitable in the competitive lump sum environment. Between 2004 and 2008 the engineering market became less competitive from an engineerÆs perspective due to the high demand for engineering services in a high price commodity market. The need for innovation remained but was driven overtly by shortages in water, power and personnel and long equipment lead times. This paper discusses some of the factors that contribute to the capital cost of a project and the scope for improving the likelihood of financing and increasing the project net present value (NPV). Case studies with recent large copper concentrator projects will be used to demonstrate how a value driven approach to project and plant layout can result in significant improvement in NPV.

Jan 1, 2009

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By F. Samimi Namin

During the process of developing surface or underground mines, some sites are considered for dumping of surface soils, while others are applied to reclaiming surface and waste disposal. For each kind of overburden, whether it be waste rock, low-grade material, or process tails, a separate storage site is considered so that it becomes possible to transport or recover the overburden separately. Decision-making must be completed by means of a selection process which takes into account the best methods of alternative sets in order to achieve these goals. This decision- making involves many parameters that are inter-related in that changes in some parameters affect the others. There are many methods of decision-making, however, Fuzzy Multi-attribute Decision-making (FMADM) and its functions are studied in this paper. The advantages of this method lies in its theoretical background, formulation, revising capability, unlimited alternatives, and consideration of the counteraction of the different parameters upon one another.

Jan 1, 2007

By Ashis Bhattacherjee, Bijay Mihir Kunar

A literature review on quantitative analysis of mine safety studies revealed that investigators use a wide range of statistical techniques for the analysis of mine injury data. Researchers have addressed the various issues of accident causation and prevention through analysis of mine injury data collected from mines. These studies are generally based on historical accident/injury data without considering the injured person/population at risk. In this paper, a public health approach, based on scientific methods of epidemiology, is presented to address mine safety issues. Epidemiology is the scientific study of disease and injury patterns among populations in time and space. Originally, epidemiology was concerned with epidemics of communicable diseases. Then it was extended to non-communicable diseases. Safety researchers found that epidemiologic methods are the best tools for injury research, because the occurrences of injury and the occurrences of disease are quite similar. As a result, some researchers started applying this concept to injury research. This paper presents some of the techniques used in epidemiologic studies and illustrates the application of a case-control study design to evaluate the role of some risk factors associated with injuries in underground coal mines. In this study, the injured persons were identified and, simultaneously, interviews were conducted to find the significant risk factors responsible for occupational injuries in coal mines.

Jan 1, 2011

This paper presents a resume of the likely profitable mining areas in New Zealand. It covers the main 'minerals' û gold, coal, oil and gas, ironsands, silica sands, clays, lump silica, perlite, sulphur and limestone. The potential mining projects are depicted on a map of New Zealand together with the associated works involved in hydro-electric and geothermal power development requirement for industries such as aluminium, nickel ferro-silicon or silicon carbide production. The political need for mining development to relieve unemployment and reverse emigration is stressed. A case is made for exploration and development assistance by government in labour re-training, energy supply and transportation, if the tremendous losses through lack of use of human and industrial resources are to be rapidly reduced. These losses are currently estimated at $10 000 000 000 per year. The need for protection of the sanctity of contract and security of tenure of all mining operations is touched on briefly as is the need for a reasonably balanced view on conservation. However, as both of these are more properly covered in papers on the legal and environmental aspects of the mining climate, they are presented here only as they affect the economy of the mining operation. Finally, there is a brief comment on the mining climate in New Zealand relative to Australia and South Pacific mining operations.

Jan 1, 1990