Search Documents

By Everson P. T, Moyle F. J

Magnesite-rich and dolomite-rich ores from the Savage River region of Tasmania are being considered as potential feed material for a commercial process for production of magnesia.Two selected samples have been characterized by chemical analysis, X-ray diffraction, and differential thermal and thermogravimetric analysis. The materials differ in calcination behaviour, with magnesite decomposing at a significantly lower temperature than dolomite. Calcination conditions have a marked effect on the rate and percentage of magnesium dissolved as the bicarbonate when slurries of the calcine are leached with carbon dioxide. From a process point of view, the feed should have the highest possible magnesite/dolomite ratio, while the optimum calcination conditions are determined by the behaviour of the magnesite component of the feed.From batch calcination tests, it is apparent that the optimum calcination conditions for magnesite-rich ore are a temperature in the vicinity of 700°C and a calcination time of one hour.

Jan 1, 1981

By Driver R. C, Moelle K. H R

This paper is dedicated to the memory of our friend Peter McKenzie who contributed much to the knowledge of the New South Wales Coalfields.ABSTRACTA fossil river system was recently mapped over parts of the Southern Coalfield, N.S.W. This river system occurs in the roof strata of the Bulli Seam. Sandstone of a fluvial nature was deposited in its course. The sandstone exhibits strong sedimentary vectorial properties and has a marked influence on strata-control in colliery workings.The sedimentary features analysed indicate an approximate S200W flow direction. Petrological studies reveal a clastic, well-cemented sedimentologically and structurally anistropic rock type. Washouts have been found and isopach maps of both sandstone and underlying roof-strata have been compiled. Relevant measurements were carried out in existing colliery workings and on bore cores.Optical determinations of feldspars revealed the presence of plagiocIase feldspars with few exceptions. Most of the feldspars are altered to clay minerals. It was found that a geographical trend exists in the distribution of feldspars, with more basic plagioclase in the northern part of the field.The source area of the fluvial sandstone lies to the north of the Southern Coalfield.Petrofabric analyses were done on several specimens of the fluvial sandstone. In the vicinity of major disturbances, penetrative fabrics were discovered.Calcites (e, 0112), micas (001), and quartz (crystalIo graphic c) show preferred orientations.

Jan 1, 1967

By G R. Mould

The paper presents a general background to the subsidence research program being undertaken by the Department of Mineral Resources and Development in New South Wales. The results of the studies undertaken over the last ten years are summarised. The differences between these results and those obtained by the National Coal Board are discussed. The results of a study carried out on the effect of total extraction beneath a freeway in the southern coalfields are discussed in some detail. The procedures developed for the construction of a 500 mm diameter natural gas pipeline crossing a number of collieries in the northern coalfields are also outlined. The future direction of the Department's subsidence research program is discussed.

Jan 1, 1980

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

By K. Rainer Massarsch

In some parts of the world, vibrators are used extensively for different types of foundation engineering projects. If used correctly and in suitable soils then vibratory pile driving for example is very efficient. However, soil conditions and the installation procedure have great significance for the driving resistance and affect the bearing capacity of vibrated piles. Also the intensity of ground vibrations which are transmitted to the surrounding soil is affected by the vibration process. In spite of the increasing use of vibrators and the rapid development of vibrator technology, many aspects of pile-soil interaction are not yet understood. In order to asses the importance of factors, which govern pile installation (and extraction), it is necessary to consider the entire chain of vibration energy transmission from the vibration source to the pile, the interaction between the vibrating pile and the soil and the wave propagation in the subsoil, Fig. 1. [ ] Fig. 1. Transfer of vibration energy from the vibrator through the pile into the ground In the present paper, some important aspects of vibratory driving and their significance for pile installation and soil compaction will be discussed.

Jan 1, 1995

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Hindmarsh J. W, McCoy A. E R

Instantaneous outbursts of coal and gas have occurred at various times in several working districts of Metropolitan Colliery, N.S.W.They have occurred in headings only, under both hand and mechanised conditions, and with seam gas ranging from mainly methane to nearly pure carbon dioxide. A modification of inducer shotfiring using a shear cut was introduced in 1955, and in 1961 full face firing both to a machine cut shear and off the solid was introduced. The current series of outbursts -1961 to 1963 - has been induced under these systems with full control of the time of outburst, but without prediction, and with some disappointing production features.Various aspects of current conditions and practices at Metropolitan are considered singular, such as the coarse granulometry of outburst coal, the prevalence of floor heave, the absence of strong structures at outburst sites, the possibility of outburst at any stage in pillar formation up to the last few yards, the effect of rate of advance on outburst occurrence, and the mildness of many outbursts experienced.It is concluded that inducer shotfiring is a reliable control but it suffers by comparison with outburst-free conditions, and that control by preyention would be preferable.INTRODUCTIONThe phenomenon of instantaneous outbursts of coal and gas has been described in detail previously (Hargraves, 1958). Briefly, it is a combined gas and stress hazard of deep coal mining, usually occurring in virgin work and during active face advance, when coal and seam gas burst from the face into the workings.Instantaneous outbursts have occurred sporadically at Metropolitan Colliery, N.S.W., since 1895. Early outbursts were recorded as firedamp and recent outbursts are of blackdamp.Mining methods used have been conventional hand work, with progressive and relatively complete mechanisation over the past 25 years to substantially conventional...

Jan 1, 1964

By Eduardo Macedo Junior

O presente trabalho descreve o desenvolvimento de uma nova especificação para a Linha de zincagem numero 3 (LZC#3) da Companhia siderúrgica nacional (CSN), de grande demanda e aceitação, alta produtividade e foco nos requisitos do cliente que tangem qualidade superficial e características metalúrgicas (resistência mecânica) em aços para atendimento do mercado Norte-americano. Este novo produto tem como característica o ciclo de recozimento com velocidade alta para obtenção de microestrutura 100% encruada na saída do equipamento e limites de escoamento e resistência acima de 500 MPa. A combinação dessas características do produto junto com as características do processo tornou a especificação “ASTM-A653MSS80CL1” um grande desafio para garantir qualidade superficial sem comprometer as propriedades mecânicas especificadas assim como a integridade do equipamento. O baixo custo de produção associado a alta produtividade desse produto fazem da especificação “ASTM-A653M-SS80CL1” um produto de extrema importância para a estratégia adotada pela CSN, mantendo dessa maneira sua competitividade no mercado Norte-americano e garantindo capacidade máxima de produção do seu equipamento em tempos de retração do mercado interno.

Aug 17, 2017

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

In this paper, the scientific bases of creation of simulation modelling systems of excavator-truck-conveyor complex work are represented. During the simulation modelling process of big mining and transport systems work the strict and full account of an order and sequence of all operations of simulated process is carried out. Step-by-step fixing of mining and transport system elements condition - excavators in loading and unloading points, trucks, road section, unloading points in storage bin, crushers and conveyors is conducted. Work and idle time of system elements are considered. During modelling process the information characterising system work as a whole is collected. It allows us to establish qualitative and quantitative influence of each system element on the final results of its functioning and provides to estimate rationality of a particular organisation variant of mining and transport equipment interaction from technological positions. Simulation results are: economic and technological indicators of mining and transport complex functioning of the period for each subsystem, as well as on the road, the points of loading, unloading and reloading.

Dec 6, 2010

IN all wet concentration processes it is of primary importance to determine to what degree the crushing must be carried in order to obtain the maximum profit per ton of ore milled.To effect a clean separation, either by gravity or flotation treatment, between either one valuable sulphide from another, or a sUlphide from the gangue, the ore must have been subjected to grinding to such an extent that the particles to be separated are completely liberated from each other.Insufficient crushing will result in either an incomplete separation of the sulphides from each other, and thus a loss of the one sulphide in the other, or else a loss of the valuable sulphide in the gangue.This being so, the question arises whether the added cost of extra crushing would be economically warranted by the increased recovery consequent on such a step.

Jan 1, 1927

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

Solvent extraction has recently been introduced into Australian hydrometallurgical practice for the production of a high grade uranium concentrate from El Sherana ore by a sulphuric acid leach and solvent extraction process. The solvent is a 5 per cent solution of tri(iso-octyl)amine in kerosene modified with 4 per cent of a long chain alcohol. The stripping reagent is a molar solution of sodium chloride.Preliminary testing for the development of the process showed that the leach liquor was quite amenable to the solvent extraction process and that the equilibrium and rate considerations of both the extraction and stripping steps were very favourable.The industrial plant contains four stages of extraction, three stages of chloride stripping and one stage of secondary carbonate stripping. An internal type of mixer-settler is used for the stagewise contact, the design being based on tests with model equipment.The performance and control of the industrial plant is satisfactory; 99·7 per cent of the uranium is recovered for a loss of 0·3 gallons of kerosene and 0· 4 pounds of amine per 1,000 gallons of liquor treated.INTRODUCTIONThe processing of El Sherana uranium ore from the South Alligator River valley commenced in April, 1959, and thereby introduced into Australian hydrometallurgical practice the unit operation of solvent extraction on an industrial scale. Although there are now some twelve mineral processing plants in the United States and Canada using solvent extraction, its application to the field of primary hydrometallurgy is quite new. Prior to 1956 none of these twelve plants was operating and hydrometallurgical application waslimited to the refining of comparatively high grade uranium compounds and fission products from nitrate and nitric acid solutions.

Jan 1, 1961

By M Wortley, R Morrison, T Rivett

The tracking of ore through process hold-ups such as stockpiles has been traditionally been difficult to achieve. The inability to pinpoint the exact source in the mine of material that is feeding a processing plant has led to inefficient mine-mill reconciliation processes. In addition, a lack of understanding of the behaviour of ore in process hold-ups such as bins and stockpiles often leads to poor predictions of plant performance and to poor reconciliation of this to the orebody.This paper reports on two short case studies. One case study addresses tracking ore from various parts of two mines to the concentrator. The other follows synthetic particles through the coarse ore stockpile. Both studies use radio-frequency identification (RFID) tracer technology. The paper concludes by discussing general strategies for implementation of such concepts into mine-mill metal accounting and reconciliation systems. As shown in this paper, reliable ore tracking systems will allow much more effective mine-mill reconciliations as well as the ability to model process hold-ups with regard to size by residence time distributions. This should, in turn, allow metallurgists to have a better understanding of the size and grade of material that will report to the plant at different process hold-up (eg stockpile) conditions.

Jan 1, 2009

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By P Paredes, T Leaño, D Gajardo, C Tramón, S Peñaloza

The definition of an ore handling system and its consequent layout design is of crucial importance in cave mining projects. It not only represents the main driver in the production capacity and reliability of the mining system, it is also a fundamental variable in the footprint’s development time and cost.In recent decades, load-haul-dump (LHD) tramming distance optimisation through the allocation of several orepasses inside the footprint has been the most common practice in ore handling system layout definition at Codelco’s operations. Today, the improvement of existing technology, such as higher-capacity LHDs and jaw-gyratory crushers, and intensive preconditioning techniques to improve fragmentation allow the conceptualisation of simple and highly productive ore handling system layouts for wide caving areas that avoid the complexity and high cost of developing numerous orepasses inside the footprint.The initial macroblocks of the Chuquicamata underground mine project (PMCHS) consider an ore handling system layout in which LHDs dump into orepasses located inside the footprint area. The ore is then transferred into crusher chambers located below the production level, where it is crushed by jaw crushers and then conveyed to surface. In an effort to reduce development time and costs, a new ore handling system layout for the PMCHS experimental macroblocks was engineered using improved technologies and techniques in a simpler mining system. This paper compares the new ore handling system layout for the project’s experimental macroblocks with the traditional LHD-orepass layout in terms of production capacity, reliability, development time and cost.CITATION:Paredes, P, Gajardo, D, Leaño, T, Peñaloza, S and Tramón, C, 2016. Simplifying the ore handling system through the use of current technology at Chuquicamata underground mine project, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004