Search Documents

A brief review is given of the history of the Colliery to date together with the reasons for the development of an additional seam.Investigations into the quality of the coal ami its suitability for the production of metallurgical coke and determination of the economic mining limits and coal reserves are discussed. The commencement of mining operations and the inter-seamarrangements necessary for the disposal of coal won are described with the stages in the opening out of the seam itself and the reasons for the installation of a 48-in. trunk conveyor belt. Choke and manning of face equipment are considered and also the work of secondary development and pillar extraction.It is concluded that with modern face equipment and conveyor belt lines, concentrated mining followed by immediate extraction of pillars is practicable and is giving excellent results at Burwood Colliery.INTRODUCTIONBurwood Colliery, the total holding of which now comprises some 3,140 acres of land and 1,450 acres of sea leases, has mined the Borehole Seam since 1883. The early work took place from Nos. 1 and 2 shafts at Glenrock Lagoon and later on at Nos. 3 and 4 shafts at Whitebridge to which the centre of operations shifted in 1893, shaft sinking at this latter area having commenced in 1888.As all the early operations were confined to the Borehole Seam, reserves of coal on this horizon had been considerably reduced by the mid 1930's, so a cross measure drift was driven to the Victoria Tunnel Seam which is about 300 ft. above the Borehole Seam, and fully mechanized coal winning commenced from the second seam in 1938. Subsequently this cross measure drift was extended to the Borehole Seam and complete mechanization of the south-west sections of this seam achieved by 1945.Four track mounted mechanical units were put into operation in the latter area and these worked in a southerly and...

Jan 1, 1958

By Thomas M. Barczak

The 1990s brought an unprecedented increase in the development of innovative technologies to provide more effective and easier-to-install roof support in underground mines. To facilitate the application of these technologies in improving mine safety, the National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a Windows-based software program that provides mine operators with a simple and practical tool to make engineering decisions about the selection and placement of these various roof support technologies. The program includes a complete database of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. A support design criterion in the form of the required support load density at a specified convergence can be established from four options: (1) a database of measured ground reaction obtained from various mines or ground behavior information input by the user,(2) load requirements based on a detached roof block or rock failure height, (3) criteria based on the current roof support system, and/or (4) arbitrary criteria set by the user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user-specified support installation. In addition to these performance measures, STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made, including a graphical analysis of relevant support parameters. This paper describes STOP and its application to optimizing standing secondary roof support systems.

Jan 10, 2000

By Onur Kacar

A numerical approach has been implemented to assess the settlements of pile groups bearing in clay. A three-dimensional finite element program has been utilized to model a vertically loaded spread footing, a single pile and a pile group. The soil-pile interaction was modeled with elastoplastic soil and interface elements. The model has been calibrated using a full scale load test results of the spread footing. The load transfer between the pile cap and the piles was assessed and compared with the measured load transfer. The predicted settlements for the pile group were compared with the settlements measured in the load test. Two analytical methods were adopted to predict the pile group settlements and they were compared with the measured values. The group effect determined from the analysis and load tests was compared with the interaction factor approach. It was shown that three-dimensional finite element approach can be successfully utilized to assess the soil-structure interaction and hence the load transfer between the piles and pile cap. Also, it was shown that the interaction factors method and equivalent footing method work well in the working stress range, however they underpredict the settlements at larger loads. INTRODUCTION The settlement and stress distribution of pile groups have been traditionally estimated based on load test results of single piles and accounting for the group effect using various approaches. The most widely used approaches are group interaction factor method, equivalent footing method and equivalent pier method. These approximate solutions are used very commonly in practice as full-scale load tests on pile groups are very expensive and time consuming. These approximate solutions are also adopted in design guidelines such as AASHTO LRFD Bridge Design Guidelines (2014) and FHWA Design and Construction of Driven Pile Foundations (2016). In this paper, a full-scale foundation load tests performed by Nagai et al. (1961) and reported by Koizumi and Ito (1967) is modelled using a three-dimensional numerical method. The settlements and the stress distribution on foundations were then compared with the traditional equivalent footing method and interaction factor methods.

Jan 1, 2018

By L Lorenzen, H Muller, L Bernard

Australian companies and consultants are becoming ever more involved in projects in African, South American, East European and Middle Eastern countries. However, significant differences in culture and approach to projects sometimes make these projects challenging for reasons that are not purely technical. Often the challenges are rather related to how the project owner and local authorities perceive the reality. These perceptions and sometimes unrealistic expectations regarding project costs and potential outcomes need to be addressed by the æWesternÆ project developer and consultant.This paper will discuss the specific experience of Snowden in studies commissioned by companies from such countries for the development of very large, low-grade gold deposits in some of the most inhospitable areas in the world. The paper will further review similar projects undertaken in other ænew worldÆ countries and compare these to the initial Snowden experience.As the process operating costs of operations in many of these countries are extremely competitive when compared to the typical Australian operating costs, the paper will review the operating costs and the factors which may be pertinent to a large project of this nature, both in the Australian and the ænew worldÆ context. Will Australian-based operations be able to compete in the global gold market when the gold price softens again, as it will do at some stage in the possibly not-so-distant future?CITATION:Muller, H, Lorenzen, L and Bernard, L, 2013. Challenges of developing low-grade deposits in ænew worldÆ countries from a mining consultantÆs perspective, in Proceedings World Gold 2013 , pp 307-314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By David A. Summers

Coal is increasingly viewed as one of the major fuel resources of this country for the remainder of this century. The need to extract a greater percentage of the coal in a given seam, together with advantages of improved safety, indicates that longwall mining will become more widely used within this time frame. A novel method of mining coal on a longwall face, utilizing high pressure water jets, is herein described. The mining machine proposed will exploit the stress conditions which exist on a longwall panel in order to achieve the required productivity while at the same time reducing respirable dust and methane ignition hazards. The water jets will excavate only the boundary of the extracted seam section, and thus the energy requirement of the machine will be minimized. The action of the machine is similar to that of an existing coal plow, except in that the wedge teeth of the plow are replaced by oscillating high pressure water jets. The machine can, therefore, cut to the depth and at the speed of existing shearer units at equivalent power levels. The removal of impact stresses from the machine will reduce downtime required for maintenance and replacement of picks and lower the load on the haulage motor of the system. The ability of the machine to increase the depth of cut without an increase in horsepower will further improve productivity when transportation systems to remove the greater production are in operation.

Jan 1, 1974

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

By Lawrence Pelham

Introduction Fluorspar demand or consumption has been taken for granted in recent years, except for those that produce, market, or consume the commodity. Thinking used to be that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The US Bureau of Mines (USBM) published an assessment of world fluorspar reserves and resources. It created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The US and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. Goals for the government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. US production and distribution Fluorspar Fluorspar shipments from US mines reached an all-time high near the end of World War II in 1944 at 375 kt (413,800 st). Eighty-two mines produced more than 453 t (500 st) each, and 10 mines produced more than 9 kt (10,000 st.) each. Illinois supplied 43% of total shipments. Consumption in 1944 was 372 kt (410,200 st), of which 56% was used by steel producers and 32% by HF producers. This was the last year that US production exceeded US consumption. The post-World War II record for fluorspar shipments occurred in 1951 at 315 kt (347,000 st) 58 mines produced more than 453 t (500 st) and eight mines produced more than 9 kt (10,000 st).

Jan 11, 1986

Open pit mine plans define the complex strategy of displacement of ore and waste over the mine life. Various mixed integer linear programming (MILP) formulations have been used for production scheduling of open pit mines. The main problem with these models is the inability to solve real size mining problems. We present a mixed integer linear programming formulation for the open pit long-term production scheduling problem. To reduce the number of binary integer variables in the formulation, we aggregate blocks into larger units referred to as mining-cuts. We present a semi-supervised clustering algorithm which aggregates smaller blocks based on rock types and grade ranges into mining-cuts without introducing an error in the grade estimated values. The cluster-based aggregation algorithm is fully integrated into an MILP mine production scheduling prototype software. We have implemented, verified, and validated our models. The efficiency of the new platform is evaluated through iron ore mine case study.

Dec 6, 2010

"Status of the Mineral Industries" provides a written and graphic view of the Nation's mineral position and its mineral industries. The report, issued annually by the Bureau of Mines, U.S. Department of the Interior, describes recent activities in mineral production, consumption, imports, exports, and uses of significant minerals and mineral raw materials. Charts profile trends for the past 28 years in supplies and uses of iron, steel, major nonferrous metals, primary nonmetallic construction raw materials, fertilizers, and plastics. Also included are current and historical financial data on the mineral industries, such as debt-equity ratios, asset-to-liability ratios, and plant and equipment expenditures.

Jan 1, 1979

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

By M Olsson, U Nyberg, K Widenberg, P Svedensten, F Ouchterlony

During 2007 and 2008, the project Optimal Fragmentation in Blasting II was conducted at the Långåsen quarry of NCC Roads AB near Arlanda. The main goals were:an evaluation of the effect of using electronic delay detonators (EDDs) in quarry blastinga validation of the design curve concept introduced at the Vändle quarry.Five production blasts were monitored. After a first trial round, the remaining four rounds each had about 100 Ø89 mm holes in a 14–19 m high bench charged with site mixed emulsions. In rounds 1 and 2, a tighter pattern than normal was used in one half of the rounds, raising the specific charge there from 0.7 to 1.0 kg/m3. Non-electric initiation was used with two holes per 25 ms delay in-row and 67 ms between rows. In rounds 3 and 4, electronic delay detonators were used instead, with 10 and 5 ms in-row delays respectively.The monitoring encompassed drill hole collaring and alignment, in-hole deviations, the rock structure in the bench faces from 3D imaging, first row burdens, etc. Eleven 400 t samples were taken from the muck piles and sorted in the quarry and sieved in the laboratory (lab). The lab data made up a fines tail that was grafted onto the in-pit sorting data to form sieving curves for the test piles. These curves were then compensated for the absence of boulders to construct the sieving curves for the blasted muck pile.These have been used to derive fragmentation model formulas for the non-electric rounds, also called design formulas. They are based on blast geometry, charging data and the properties of the rock mass. The formulas may be used to estimate the effect of changing blasthole pattern, borehole diameter and stemming length for example.The use of EDDs gave several unexpected results. In comparison with non-electric initiated rounds with a somewhat lower specific charge the fragmentation was much coarser; x50 increased from 160 to 200 mm. The effect of raising the specific charge in the non-electric initiated rounds from 0.72 to 0.99 kg/m3 was a much finer fragmentation; x50 decreased from 160 to 120 mm.CITATION:Ouchterlony, F, Nyberg, U, Olsson, M, Widenberg, K and Svedensten, P, 2015. Effects of specific charge and electronic delay detonators on fragmentation in an aggregate quarry – building fragmentation model design curves, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 727–740 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D. M. Lane, J. M. Berkoe

Engineers and Owners share a common desire to build reliable, efficient plants on schedule at reasonable costs. This paper describes one tool that Bechtel finds can integrate these objectives by “putting innovation into practice”. Examples of such innovative engineering practice include the use of computational fluid dynamics (CFD) to determine efficient designs. This paper outlines several examples of CFD applications on actual Mining and Metals Projects from around the world. The focus here is to highlight the modeling objectives, analysis strategy, actual benefit obtained from the work, lessons learned to improve future efforts and the common mistakes that can obscure the correct or best results, despite impressive graphics. The tools are powerful, and the results are more powerful when applied with skilled and well-directed human effort and ingenuity.

Jan 1, 2000

By Moresby J. F

Segregation roasting was used to recover more than 85 per cent of copper from crushed, minus 14 mesh refractory furnace-lining bricks. A plus 14 mesh fraction: which was high in copper, could be recycled directly to the smelter, giving an overall recovery of approximately 90 per cent. An oxidation roast at about 700°C was necessary, before segregation roasting, to convert copper sulphides and copper metal to sulphates and oxides. Withsegregatron temperatures in the range 600°-650°C the quantities of solid carbon and NaCI required are 2-5 per cent and 1 per cent respectively. P.V.C. coating from scrap copper wire can be used instead of NaCl as asource of hydrogen chloride for the segregation reaction.

Jan 1, 1978

By N. M. Skarbøvig

Safety nets have been used selectively in several South African mines over the years. Recently, however, an increased emphasis on mine safety has seen a resurgence of their utilization underground. This renewed interest has, however, also raised questions about the design and performance of these nets and their practical applications underground; these are the subjects of this paper. Generally, mine safety nets are used to protect personnel from falling rock in temporarily supported development ends, tunnels, ASGs and stopes. These diverse applications each require specific net designs, resulting in a wide product range. As a rule, however, mine safety nets need to carry specified static or dynamic loads with the least possible deformation. Because of the application-specific characteristics of mine safety nets, there is no South African national standard for them. Consequently, neither the SABS, nor the CSIR, performs standard tests on these components. In 2007, therefore, SIMRAC made available their Savuka facility for the testing of mine safety nets; the Savuka drop test became the accepted industry test standard for mine safety nets. From late 2007 to mid 2009, Norsenet, in collaboration with SRK Consulting, the designated operators of the site, conducted approximately 200 tests, which formed the core of Norsenet's database of safety net performance under various loading conditions. The test specimens comprised a wide range of net materials and config¬urations; the materials included: high density polyethylene, polypropylene, polyester, nylon, as well as a blend of polyester and polypropylene used primarily for reinforcement ropes. Net configurations encompassed the following parameters: net type, i.e., knotted nets or sewn nets; net strand type, i.e., braids, twines, or webbing; strand size; mesh size; mesh orientation, i.e., parallel or oblique to the net edge; net edge reinforcement, i.e., knotted, tied, with or without reinforcement ropes; internal reinforcement ropes, i.e., diagonal ropes and/or orthogonal ropes; as well as net attachment options, including loops and chainlinks. From the number of variables listed above, and the limited number of tests available, it can be appreciated that the findings of the test series required careful scrutiny. Nevertheless, principal performance factors clearly emerged: besides the obvious net mesh variables, such as net strand material, strand diameter and mesh size, it was the configuration of the reinforcement ropes and their attachment to the net panel which had the strongest influence on net performance. All the structural elements of a safety net need to work together to transfer the imposed load from the net panel, through the reinforcement ropes, to the net attachment points. In this load transference chain, the weakest link limits the strength of the structure. From this development work, Norsenet has gained valuable expertise to custom-design and manufacture nets to clients' specifications. The examples presented in the paper will also show the experience acquired in the installation of nets underground. Future work will include the establishment of a state-of-the-art net testing facility at Norsenet's factory in Vredenburg.. Keywords Mine safety net, safety net, protective device, mine safety, safety net design, safety net performance, safety net applications.

Jan 1, 2011

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4 (the main product) and other waste metal chlorides. The TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amount of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify effects of using different feedstocks.

Jan 1, 2015