Search Documents

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By Gang Guo, Zhong Liu, Yi Zhang, Jingchun Lu

"Abstract Application of soil displacement screw pile (known as SDS pile) has been experiencing accelerated growth in Chinese deep foundation industry because of its technical advantages, environmental benefits, and cost effective as well. As bored displacement piling, SDS piles are able to perform better than non-displacement piling such as CFA plies due to changing the stress state in the soil around SDS piles during the installation. Therefore the design methods between the conventional pile type and SDS pile type have some differences. Based on the methodology research, current Chinese piling rigs, displacement augers and piling projects are introduced, and the current design approaches for SDS piles in China are also described. Moreover, the design results are verified by using full scale load tests, and a part of the research results of SDS piling system acquired in China are presented.IntroductionThe Continuous Flight Auger Pile, also known as the CFA pile, has occupied about 22% in the pile market all over the world (Van Impe, 2004; Bottiau, 2006). The CFA piles are usually used for large diameter (600mm~1200mm) pile foundations and deep excavation projects. Whereas the small size CFA piles (400mm~500mm) are mainly applied for composite foundations in China. In the past 10 years, the new technology of soil displacement screw piling has been applied worldwide (Prezzi et al., 2005). And it is also extensively used for high-rise buildings, industrial plants and railway projects in China (shown in Figure 1)."

Jan 1, 2014

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By Kristen E. Coose

Concrete is a mixture of a fine aggregate (sand), a coarse aggregate (gravel), cement, and water. Cement itself is the most expensive of the ingredients but generally amounts to only about 10% of the concrete mixture. Cement raw materials include calcium, alumina, iron oxide, silica, and gypsum. They are heated and chemically changed into clinker "minerals," which are then ground and shipped as cement. Each of the four main clinker minerals-tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium aluminoferrite-impart specific strength and compositional properties to the final concrete product. During hydration of the cement, chemical changes produce new minerals that include calcium silicate hydrate gel (C-S-H, the main constituent of hydrated cement paste), calcium hydroxide, and calcium, sodium, potassium, and sulfate ions, among others. Two main reactions can occur that may be deleterious to concrete. Normal cement pore solutions, in a hydrated cement, contain sodium hydroxide and potassium hydroxide. If these alkali concentrations are too high, they can react with the siliceous aggregate (alkali-silica reaction, or ASR) to form an alkali-rich calcium silicate hydrate gel (C-N+K-S-H), which, upon prolonged contact with water, can expand to crack the concrete. The other deleterious reaction occurs when the mineral ettringite (Ca6A12(S04)3OH12. 26H20) forms after the concrete is hardened (delayed ettringite formation) and cracks the concrete. Many of the concrete bridges and structures built in New Mexico in the past 20 years are in need of replacement due to deterioration. Many others constructed very early on in the century are still sound. By collecting and analyzing samples of both old and new concrete and good and bad concrete, we compared their differences on both a microscopic and macroscopic scale. Samples taken from concrete sidewalks, parking lots, drainage canals, spillways, and a railroad-trestle foundation have construction dates that range from 1923 to 1997. They were analyzed by electron microprobe and by petrographic microscopy. Cracks, air voids, and aggregate alteration were primary locations for investigation and analysis. Using the electron microprobe, ettringite was found in voids of most of the samples, both in good and bad concrete. This leads us to believe that ettringite formation is not causing distress in the concrete. There was one exception in which ettringite was found lining a crack. In this instance, ettringite may have the ability to further the cracking and cause distress. No alkali-silica gel was identified with the microprobe. Using the petrographic microscope in cross-polarized light, a light-brown material was observed that lined some of the air voids and cracks; however, exact mineralogic identifications were not made. Although many instances of chalcedony and other deleterious quartz phases were found, no clear evidence of ASR-gel deterioration was present in our samples using these methods. However, positive identification of the ASR gel was made on an in-place concrete near one of our sample sites and in several sample cores using a newly developed chemical test for the soluble potassium ions associated with the gel. The chemical used in this test is sodium cobaltinitrite, Na3Co(NO2)6.

Jan 1, 1999

By Sterling J. Anderson

Through the use of nondestructive testing techniques, the Bureau of Mines is pursuing a goal of improving the efficiency of the rock excava-tion process. Toward this end, 44 laboratory tests were conducted to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool. An acoustic emission CAE) transducer was used to monitor the test samples as they were loaded. The signal from this instrument was recorded in real time along with the radial and axial loads generated by the fracturing device. Through the review of these signals on a common-time base, it was possible to see the relationship between the developing fracture and the loading conditions. As a part of the posttesting investigations, samples that were pletely fractured were sawn and ground to expose the fractures. examination of these samples allowed approximations to be made incom-Visual of the total surface created. Surface area approximations were also made for the completely fractured samples. Quantitative analyses· of the AE signals were conducted for comparisons with the calculated surface areas.

Jan 1, 1987

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

The Illawarra District, from 50 to 100 miles south of Sydney, is one of the State's important coalfields. It extends from Clifton on the north, to the Shoalhaven river on the south, and from the coast westward beyond the coastal scarp.For descriptive purposes, this area falls naturally into two zones:(a) the coastal belt backed-by the eastern edge of the plateau;(b) the plateau, westerly from the coastal scarp.(a) The Coastal Belt.A triangular shaped area extending from Clifton to the Shoalhaven river, composed for the most part of soft coal measures strata of Permian age, which, on weathering, undermines the massive overlying Mesozoic sandstones and causes the gradual recession of thecliffs.South of Wollongong, upper marine sediments and contemporaneous igneous rocks make their appearance beneath the coal measure beds and occupy the greater portion of the coastal belt.(b) Plateau Area.Extending westerly from the coastal escarpment is a plateau known as the Robertson Tableland, composed of Triassic sandstone and shales dipping gently in a northerly direction, and capped in places by Wianamatta. shales and r.rertiary basalts. This tableland is approximately 2400 feet above sea level in the vicinity of Robertson, and gradually falls to about 750 feet at Waterfall.The plateau area for the most part is highly dissected, rough, steep gorges alternate with sharp ridges.A large part of the northern watershed of the Robertson tableland is a reserve for Sydney water supply, and large dams have been constructed at Cataract, Avon, Burke, and Cordeaux.

Jan 1, 1938

By Dean E. Matthews

The concept of a pile for construction is credited to a Neolithic tribe called the "Swiss Lake Dwellers" who lived in what is now Switzerland about 6,000 years ago. They used piling, not for supporting heavy loads as we do today, but for elevation to protect themselves from wildlife. The Romans often used piles, and built many structures, including buildings, homes, bridges, roads and viaducts on piling. The Romans built the first bridge across the Tiber River in Rome on timber piles in B.C. 1620. Homes in the cities of Venice and Ravenna were built on piles from B.C. 100 to A.D. 400. The Romans also built the first bridge across the Thames River in London in A.D. 60 on timber piling.

Jan 1, 2003

By Daniel P. Lathrop, Leslie C. Taylor, William L. Fourney

Except when the target is on the surface, e.g. a tank track, the most important loading mechanism from a buried charge on a target above it is the impact of soil propelled at the target by the expanding gas from the explosion. Detonation of a shallow buried explosive generally yields an unstable interface between the rising soil and the air which appears to be the result of Richtmyer-Meshkov instability. Irregular “fingers” of saturated sand extend into the air above a more generalized dome of soil. These fingers move at a much higher velocity than the material between them at smaller stand off distances. As a result, the local load on the target at positions on the target at the same distance from the charge may vary by 50% or more from shot to shot or even within a single shot. This variation requires a large design safety factor to assure the integrity of design of mine-resistant vehicles.

Jan 1, 2009

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

Leading Article from "British Medical Journal," London, 4th, November, 1944.Assuming that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid, Denny, Robson, and Irwin thought that if the solubility of siliceous material retained in the lungs could be suffciently reduced the usual fibrotic response could be diminished or prevented. They discovered that aluminum powder rendered siliceous material insoluble in vitro by coating the silica particle with a thin film of gelatinous hydrated alumina, which on drying formed crystalline alpha aluminum monohydrate. The presence of this adsorbed layer on the surface of the quartz was shown by staining it with aurin. That metallic aluminum dust produced no fibrosis in the lungs was demonstrated by dust-inhalation experiments on eight rabbits. Attempts were therefore made to prevent silicosis by mixing quartz with metallic aluminum dust.Animals exposed to quartz dust developed typical silicosis in about five months, but the addition of 1 per cent. aluminum powder prevented this even after exposure had been lengthened up to 22 months, provided the aluminum powder was of a particle size below 5. This year Crombie, Blaisdell and MacPherson have reported the treatment of 34 silicotic miners by the daily inhalation of fine aluminum powder freshly ground from small aluminum pellets in a specially constructed mill. Daily treatment began with five-minute inhalations, which were gradually increased to 30 minutes. Some of the men received 300 treatments, but the majority only 200. Out of the 34 cases thus treated clinical improvement was manifested by lessening or disappearance of shortness of breath, of cough, of pain in the chest, and of fatigue. In 15 cases the condition became stationary and remained so in spite of continuous employment in silica dust throughout the treatment. The progress of the disease was assessed by means of tests for respiratory function repeated at three-monthly intervals. Obviously this treatment cannot be regarded as a cure for silicosis, since it cannot restore lung tissue which has undergone fibrotic change; but Crombie and his colleagues believe that the inhalation of finely particulate aluminum powder offers every prospect of preventing the development of human silicosis.In view of these findings, it is surprising that repeated papers by Goralewski from Germany describe various types of lung disease attributed to aluminum dust, and press for them to be scheduled under the Workmen's Compensation Act in that country. Seven hundred workers were investigated. They were making, probably by a stamping process, aluminium powder containing about four milliards of particles of dust per grain, and are reported as complaining of dry cough with pain on breathing, shortness of breath, poor appetite, and gnawing abdominal pain. Spontaneous pneumothorax developed in four workers. No abnormal physical...

Jan 1, 1945

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

THE Taranaki oil-field is situated on the western side of the North Island of New Zealand, at about its widest part, and may be said to be the most compact and fertile part of the Dominion, for, with the exception of the upper half of Mount Egmont and of the ranges adjoining, which absorb 36,000 acres, the whole of the area, minus what is taken up by the rivers and streams is suitable for settlement, and certainly two-thirds is good land. The gross area of the district is 2,417,299 acres. The principle rivers are the Wanganui, Mokau, Waitara, Patea and Waiwakaiho. Mount Egmont, which is 8260 ft. high, used to be called Taranaki, and from it the district takes its name (the Maori meaning of which is "sloping peak ").THE OIL-FIELDThe discription of an oil-field now-a-days usually resolves itself into a mass of figures and statistics, of great interest and value to the engineer and commercial man, but practically indigestible to the general public. It is the realm of the financierand the captain of industry.

Jan 1, 1912

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987