Search Documents

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By W. L. Dare

This publication is one of a series prepared by the Federal Bureau of Mines on methods and costs of producing uranium ore on the Colorado Plateau. The information it contains was gathered in 1955-58 and applies to eight small operations. (See fig. 1.) Mining costs have increased since the data were I collected, but the information should be helpful in estimating future costs I at similar deposits. The Bureau of Mines had early experience in the production of carnotite-type ores on the Colorado Plateau.3 4/ Under a cooperative agreement with the National Radium Institute in 1914-16, the Bureau mined and concentrated carnotite ore for recovery of radium, uranium, and vanadium. The ore was taken from claims in or near Long Park Montrose County, Colo., about 3 mi. south of La Salle Mining Co.'s La Salle mine, which is one of the mines described in this report. The Bureau leased the claims from Crucible Steel Mining & Milling Co., a subsidiary of Crucible Steel Co. of America, and from 1914 to 1916 produced 990 tons of high-grade ore, containing 2.6 pct. U308, and about 2,000 tons of mill-grade ore, containing 0.85 pct. U308. The high-grade ore was shipped directly to a radium-recovery plant built in Denver in 1914 under the cooperative agreement. There, commercial methods of extracting uranium, vanadium, and radium from carnotite ores were developed by Bureau personnel. The lower grade ore was concentrated at a small mill in Long Park before being shipped to Denver. The final recovery was 69,000 lb. of U308 and 8.8 g. of radium. The direct mining cost of producing the high-grade ore, including the labor to hand sort and sack it, was $35.96 per ton. Freighting the ore 58 miles to Placerville, Colo., the nearest rail point on the Rio Grande Southern Railway, cost $25.28 per ton, which included $4.55 per ton for ore bags and twine. Four-or six-horse teams pulled two wagons in tandem and made the

Jan 1, 1961

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By Louis Schaffer

The purposes of the research were to assess the applicability of new accident investigation methods to mining accidents, and to adapt those found to be applicable in the development of a new methodology for use in mining. The development included field testing, evaluation and modification of the new methodology. The report is in two volumes. This, volume one, discusses primarily the Phase I work: background research, design of a methodology for field evaluation, and preliminary field tests in Utah mines. Phase I was completed in June, 1980. Also discussed are some activities to prepare for a field evaluation during the period May 1980 -October 1981. Volume 2 discusses the subsequent field tests, modifications of the initial methodology and the results of use of the methodology in two mining companies for a period of approximately eighteen months, and in other companies for selected loss incidents during that period.

Jan 1, 1986

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By Evelynn Stirling

Agenda ? Emissions legislation ? Cummins Tier 4 Technology ? Cummins Experience with Technology ? Operation and Maintenance Impact The Emissions Challenge ? The 2014/5 emissions regulations present the most significant challenge to our customer?s diesel powered equipment design and operation in recent history? ? ?and Cummins has the solution.

Aug 1, 2013

By Youngtak Ko, Wonnyon Kim

Korean contract Mn-nodule field in the NE equatorial Pacific is composed of seven sectors showing average water depths of 4,513 - 5,025 m. Of the various factors controlling the property of Mn-nodules, water depth has a potential linkage to chemical composition, shape and abundance of nodules. To clarify such a possibility, we review more than 20 years of research data in one of the northern sectors (hereafter KR1) where there is a marked contrast in water depth. High-resolution seabed mapping clearly separates a northern part from a deeper southern part, cutting across the middle of the KR1. In terms of nodule occurrence, manganese nodules in the deeper north are comparatively larger (2-4 cm) with rough surface (t-type) and discoidal shape (D-type), while those in the south are generally small (<2 cm) with smooth surface (s-type) and irregular shape (Itype). In addition, the nodules in the north have higher metal contents including Cu, Mn and Ni. Such connections of water depths to nodule occurrence and metal contents are commonly observed in the Korea licensed Pacific nodule fields. However, the relation between nodule abundance, size and water depth may be a different story. In KR1, nodule abundance and size are probably controlled by morphological features especially in the north. Seamounts in the north continuously provide rock fragments as new nuclei for the nodules. As a result, the nodules can not grow larger than 2 cm and show the shapes of newly formed nodules (i.e., smooth surface and irregular shapes). Such an interpretation is supported by anomalously high backscattered intensities in the side-scan sonar image map of the north, which possibly reflects a younger generation of magmatic activity.

Sep 1, 2014

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By G. L. Oldright

As a rule, the usual zinc retort smelter fired with natural gas made its own burners, of which there might be 300 per block, out of standard pipe fit-tings. The gas was discharged through a feeder pipe at various distances into a cylindrical horizontal "blow hole" through a pillar block and thence into the furnace; the best location of this gas-feeder pipe was at the horizontal central axis of the blow hole; the side entry into the blow hole usually was used. The air entered the same blow hole behind the gas, through a short nipple, in the inner end of which was a constructing orifice in a clay plug; in this ,work cone-shaped funnels of various lengths also were used. Even with the air and gas correctly proportioned to each burner, small differences in their dimensions were found to influence greatly the temperatures reached, their uniformity, and consequently the percentage of zinc extracted. This fourth paper of a series on cooperative work in the zinc retort plants of the Eagle-Picher Mining & Smelting Company discloses the methods and principles followed in approximating closely the optimum dimensions for various burners, with examples from experimental and commercial furnaces showing the interrelation of such dimensions with combustion and temperatures in the furnace.

Jan 1, 1948

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By C. Velásquez, W. Bergholz, C. Spence, P. Lind

NuevaUnión SpA (NuevaUnión) is a development project located in the Huasco province of the Atacama region of Chile. It is held in a joint venture company owned 50:50 by Teck Resources Limited (Teck) and Newmont Goldcorp. It includes the Cu-Mo Relincho deposit and the Cu-Au La Fortuna deposit, with plans to utilise a single concentrator to be built at the Relincho site. The Relincho site is at an altitude of 2,000 masl and is 40 km from the La Fortuna site which is at an altitude of 4,100 masl. The project is currently completing a Feasibility Study and is reviewing equipment selection and flowsheet options. This paper is based on the current thinking, and design decisions will be finalized at the completion of the Feasibility Study. NuevaUnión is currently planning for phased operation, processing Relincho ore at 104 ktpd followed by processing ore from La Fortuna at 116 ktpd. Plans for the third phase include doubling the main processing lines and returning to Relincho ore at a processing rate of 208 ktpd. The NuevaUnión concentrator will incorporate comminution and flotation circuits that are being designed to maximize the overall economic value of the combined ore deposits. Major ore characteristics differ between the two ore bodies, such as ore competency, grindability, liberation grind size, pulp rheology, tailings properties, minerals and metals of value, as well as gangue mineralogy. Mineral processing choices have been made to optimise value from each deposit and the combined project. INTRODUCTION Between 2010 and 2013, two significant mining projects were being developed in Chile: Goldcorp’s El Morro project had recently finalized a Feasibility Study and, in 2011, had received its environmental approval for construction; and Teck Resources Limited’s (Teck) Relincho project was finalizing a Feasibility Study and preparing its Environmental Impact Study. Both projects were: Geographically close, at only 40 km apart. Considering similar infrastructure. Each was planning to have its own concentrator, tailings management facility, high voltage power line, port, concentrate transport system, seawater desalination plant and pumping system to mine site.

Jan 1, 2019

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By W. P. Huleatt, Jr. Traver, Jr. Hazen

"Vanadium and uranium occur widely distributed throughout western Colorado and eastern Utah, and a few deposits have been found in northeastern Arizona and northwestern. New Mexico. The area in which it occurs includes approximately 10,000 square miles and is generally referred to as the vanadium region of Colorado and Utah.The majority of the deposits consist of replacement bodies and impregnations of rare minerals in the lower Morrison formation of Jurassic age. The ore bodies are flat, with irregular margins, and most of them conform to the stratification.The ""rim rock"" topography of the region includes many steep-walled canyons and plateaus, which afford an abundance of outcrops that have been responsible for most of the discoveries of mineralized areas. Delimitation of ore bodies within the areas is accomplished most effectively by core drilling from the surface.The deposits were discovered in 1899 and from 1911 to 1923 wore worked extensively for radioactive uranium ores, principally carnotite.The discovery and marketing of the richer and more cheaply mined pitch-blende ores of the Belgian Congo left the Colorado-Utah deposits without economic importance as sources of radium and uranium, and the region became inactive in 1923. After a period of comparative inactivity, the rising demand of the alloy-steel industry for vanadium renewed interest in the deposits, which were known to contain that metal. By 1938, vanadium production in the area had achieved respectable proportions, and new impetus was given to it by the United States’ entry into World War II in December 1941. In 1942, new treatment plants for vanadium ores were completed in Monticello, Utah, and Durango, Colo. In order to meet the requirements of these and other plants in the region, it became necessary to open new vanadium mines and prepare old onus for production.In an effort to stimulate mining, the Metals Reserve Company initiated a stock-piling program and appointed the united states Vanadium Corporation, to act as its purchasing agent.The extra production was expected to come largely from small, independent operators whose limited funds did not permit them to maintain development and exploratory programs. Study of conditions made it apparent that extensive exploration would be necessary to sustain production, and accordingly the Bureau of Mines initiated an exploratory drilling project on a cooperative basis with the Geological Survey. The principal objects of the work were to enlarge the known ore reserves of the area and, if possible, discover new ones. The results have been gratifying in both respects."

Sep 1, 1946

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009