Search Documents

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By Sam Spearing

Free-standing supports are commonly used in coal mines in the USA, particularly when longwalling. A recent trend has been the development of prop supports. Prop supports have many advantages over bulky, crib-type secondary standing supports, particularly in regard to material handling and installation. The challenge in prop design has been to develop load capacities that can compete with crib type systems and to develop reliable (stable) yielding capability. This paper will focus on the design aspects of steel prop supports, specifically, and evaluate the various concepts that have been developed to provide easy height adjustment and sustainable stable yielding under load. The design and resulting improvement provided by recent support developments called the Quik Stik and Ball Buster are discussed in detail. Performance areas that still need improvement in the design and usage of free standing supports in general are identified and possible solutions outlined.

Jan 1, 2008

By K. C. Viveros, R. R. Ambriz, C. García, F. De Villèle, A. Talha, D. Jaramillo

Cold hole expansion on base metal, weld metal and heat affected zone of 6061-T6 aluminum alloy welds was simulated by means of finite element method. Three dimensional compact test models with a previous fatigue crack length with a relation of ??= a/W = 0.3, were used to analyze the hole expansion process. Considering the local mechanical properties for each zone of the welded joint, the optimal expansion degree (1.64 to 2.46 %) was determined. The residual stress field, through thickness, after the expansion process in all welding zones, were correlated with the crack opening displacement obtained by finite element analysis. It was observed, that compressive residual stress fields for a post-expansion, in different crack lengths, provided a crack closure mechanism for base metal, weld metal and heat affected zone. Contrary, the crack remained open when residual stresses are positive. The results are given as tangential stresses versus distance from the edge of the cold expansion and crack opening displacement as a function of applied load.

Jan 1, 2014

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

By A Giblett, K Afewu

This paper uses a case study to demonstrate best practices techniques for predicting the contribution of gravity concentration in a gold recovery process flowsheet. The case study was selected as an example of an ore with a marginal gravity gold content, which makes the value of a gravity circuit difficult to quantify. In this instance the value of leveraging a significant knowledgebase of operating gravity circuit performance to support the decision making process was demonstrated. This case study analysis serves as a useful demonstration of best practice methodologies supporting decisions to include or exclude gravity recovery in a gold recovery process flowsheet.CITATION:Giblett, A and Afewu, K, 2015. Do we need a gravity circuit or not? A case study in applying best practice, in Proceedings MetPlant 2015, pp 288–295 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By Jim Wickens, Vince Lofftus, Mark Kravetz

"This paper discusses how Bald Mountain Gold Mine (Ely, NV) dramatically reduced mercury production by treating process solutions with a liquid reagent based on organic sulfide chemistry. Cherokee Chemical Co. Inc. (Vernon, CA) markets this reagent as UNR 81 1A.A summary of the bench tests comparing various reagents is given. The ensuing plant trial is discussed and successful mercury removal results are presented. Data is presented to show that early removal of mercury in the process reduces the amount of mercury collected at retort. Data is also presented to show that use of this reagent does not reduce gold recovery. Plant trial treatment costs are discussed. Finally, the potential of this technology to substantially reduce closure costs as compared to traditional mercury removal options is discussed.INTRODUCTIONBald Mountain Mine produces gold. Mercury is a costly by-product of gold production because no revenue is generated from mercury. Traditionally, mercury leaches out with gold and follows the gold throughout the processing circuit until it is eventually condensed and collected at Retort. Minimizing or eliminating mercury production minimizes worker health and safety risks, minimizes environmental liability, and reduces costs. In the long term, minimizing mercury production will make mine closure easier and less costly.Bald Mountain Mine dramatically reduced mercury production by treating process solutions with liquid reagents called UNR 811 and UNR 811A. Several reagents were bench tested before proceeding with a plant trial. The reagent complexes the mercury to form an insoluble organic sulfide precipitate. In independent tests, the precipitate passed acid mobilization tests and is considered stable."

Jan 1, 2001

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (lMR) separators. The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.   The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By W. R. Hardwick

This Information Circular describes the development of block-caving methods and practices by the Miami Copper Co. at the Miami mine in Gila County, Arizona. It is one of a series published by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. This report gives a history of the district and outlines early prospecting and exploration including methods of sampling and estimation of ore tonnage and value at the Miami mine. Early mining methods are described, particularly those that influenced developments in the caving method. Mine exploration, development, and operating methods for block caving are described with particular attention to those factors, physical, economic, engineering, and managerial that have improved efficiency in the mining operations over a long productive period. Extraction, ventilation, wage system, safety, water supply, power plant, and shop facilities are discussed. The last section gives a brief sumary of such costs as are available for publication.

Dec 1, 1964

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972