Search Documents

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By L. A. Nemchinova, M. A. Arustamian

"For a long time tailings piles of mining and smelting complexes have met the eye being a prospecting feedstock source for many industries. Nowadays, 6.5 million tons of copper and cooper-zinc processing tailings are stockpiled in the Urals annually, as there is no technology of its processing to provide a full and complex metal extraction within mining and processing operations. In spite of large volumes of mining wastes, not more than 20% of annual overburden, approx. 10% of processing wastes, approx. 40% slags (1) are involved into processing.Based on today’s complex of economic, environmental and social challenges of ore processing, waste processing technology using existing capacities is a burning issue. Mining wastes characteristics (including fine dissemination, variability of physical and chemical properties of mineral surfaces under impact of oxidizing, leaching, etc.) predetermine challenges arising out of its involving into processing and justify high capital intensity of new construction or reconstruction projects followed by replacement of existing processing lines with new ones.In this paper, the authors propose flotation technology for mature tailings of copper, copper-zinc and polymetallic ore processing. The technology developed provides for upgrade of existing process flowsheet diagrams at minimum costs to produce additional saleable products including low-grade copper concentrate, saleable zinc concentrate and gold concentrate thus facilitates sustainable use of depleting minerals and operational efficiency due to cost-efficient processing of already mined materials, being in fact, final semi-products located near existing operations. This is particularly important for operations with standby capacities and not engaged workforce."

Jan 1, 2018

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By S. A. Kubyshkin, A. A. Agafonov, A. L. Shakhnin, S. M. Sukharzhevsky, A. A. Komlev, N. V. Vorob’ev-Desyatovskii, A. Pichugina

Cyanidation of gold ore results in formation not only of Na[Au(CN)2], but also cyanometallate complexes of some transition metals. During subsequent gold extraction from such solutions and pulps, using activated carbons (??), a number of problems arise. An effective solution of the problem is not possible without detailed knowledge of the interaction mechanism of transition metals cyanide complexes with AC particles. The chemical properties of AC particles and graphene, saturated with [?u(CN)n](n-1)- (n=2, 3), were studied by XPS, ESR, SQUID, and DFT. The obtained results were compared with the data on AC adsorption of anionic form of Ag(I), Au(I), Cd(II), Hg(II), Cr(III), Fe(II), Fe(III), Co(III), Rh(III), Ni(II), Pd(II), Pt(II) and Pt(IV) cyanide complexes. The adsorption of [?u(CN)n](n-1)- (n=2, 3) on AC from aqueous solutions in air is accompanied with oxidation of ?u(I) atoms. Besides, Cu(II) and Cu(III) compounds were found on AC surface. Quantum-chemical calculations confirmed the possibility of formation of Cu(I) complex with carbene-like sites of AC. The reactions of [?u(CN)n](n-1)- (n=2, 3) complexes and aromatic carbenes and their cation-radical were theoretically studied at DFT PBE level to obtain the information on adsorption of cyanometallate complexes on AC. Carbenes with different fragments were regarded as a model of activated carbons, which have free edge sites with paired o and n electrons. It was shown that [Cu(CN)2]- bounds firmly with triplet carbene, if one Cu-CN bond breaks. The dissociation process occurs through a multi-step spin-crossing mechanism to reduce total spin multiplicity of the metal-carbene complex. The behavior of transition element complexes in contact with AC in aqueous solutions is determined by the following characteristics: geometrical structure of ionic complexes; nature of ligands bonded to the central atom; concentration of reactive oxygen species in solution and its pH; nature of binding sites of AC.

Jan 1, 2018

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Gary Buchan

"Mine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mine operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. The acoustic emissions (AE) form of non-destructive testing has been used for decades to determine material or machine deterioration or potential failure. This paper presents the findings of research in AE with the results of laboratory bolt pull tests and comparisons to field experimentation, including AE sensors and bolt load data in an underground stone mine. The goal of the project is to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of predicting bolt failure or roof deterioration.INTRODUCTIONMine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mining operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. Typical ground control monitoring devices involve drilling into roof or rib, grouting or gluing of sensors, and dedicated cabling for data collection. One of the original goals of this research was to develop a methodology for a simple wireless device that could provide an indication or warning of potential roof bolt or roof failure. Various types of nondestructive testing (NDT) have been used for decades to determine material or machine deterioration or the potential failure of either. One type of NDT is acoustic emission (AE) monitoring, which has been studied for use in mining to predict rock bursts and mine failures since the 1940s (Obert, 1941; Obert and Duvall, 1942). The primary goal of the work was to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of evaluating bolt loading or roof deterioration in an underground stone mine. Bolt pull tests were conducted in the laboratory to establish a repeatable trend of AE activity versus bolt load. The second part of the project was to then install bolt load cells in an underground stone mine and monitor AE activity in the vicinity of mining."

Jan 1, 2018

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By S. M. Bradshaw, C. Dorfling, F. Ngandu

"Selenium removal and platinum group metal (PGM) recovery from copper sulfate leach solutions form an integral part of platinum producers’ base metal refinery operations. Recent studies found that substantially higher PGM recoveries can be achieved if excess thiourea instead of sulfurous acid is used as precipitation reagent; however, the impact of the proposed process on downstream processes was unknown. The objective of the current study was therefore to investigate the effects that excess thiourea and residual selenium present in the rich copper sulfate electrolyte have on copper electrowinning. This was achieved by performing cyclic voltammetry tests using a platinum rotating disk as working electrode, a graphite auxiliary electrode and a saturated calomel reference electrode. A synthetic copper sulfate electrolyte containing 0.01 M Cu2+, 1 M H2SO4 and varying amounts of selenium (20 – 150 mg/L) and thiourea (10 mg/L and 100 – 300 % excess) was used. The results obtained have shown that both thiourea and selenium interact with the cupric ion cathodic reduction reaction. Thiourea polarized the working electrode and lowered the efficiency of the cupric reduction reaction. Tests on the solutions with high selenium concentration showed simultaneous reduction of copper and selenium, which led to copper selenide formation. Nodule formation on the deposit surface also became significant at higher selenium concentrations. Based on these results, it was concluded that precipitation of PGMs from the copper sulfate solution with excess thiourea is not feasible due to the detrimental effect on downstream electrowinning operations.INTRODUCTION During the high pressure oxidative leaching stage in a typical base metal refinery (BMR) circuit, selenium, tellurium and some platinum group metals (PGMs) are dissolved along with the desired copper ions. The impurities (selenium and tellurium) may pass to the copper electrowinning circuit where it can result in the formation of nodular copper electrodeposits or reduced current efficiency. The presence of PGMs in solution, on the other hand, increases the precious metal inventory and potential losses of the operation. Currently, sulfurous acid is widely used for selenium and tellurium precipitation from copper sulfate leach solutions. Sulfurous acid is capable of reducing cupric ions to cuprous ions; the generated cuprous ions then react with Se4+ and Se6+ to precipitate selenium as a copper selenide (Bello, Dorfling, 2014). Recent studies have, however, proposed the use of excess thiourea as a precipitating agent for the removal of selenium and tellurium; it has the advantage of improved PGM recovery in the Se/Te precipitation step (Lottering, Eksteen et al., 2012; Mulwanda, Dorfling, 2015)."

Jan 1, 2018

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By C. Rutter, S. Nelson

"Climax Molybdenum Company’s Henderson Mine, owned by Freeport McMoRan Inc., is a panel caving molybdenum mine located 69 km west of Denver, Colorado. The mine utilizes long interconnected ore passes as part of the ore flow system. Knowing the approximate level of ore in these ore passes is beneficial for preventing increased dust concentrations in various production areas, as well as scheduling truck loading operations. Level monitoring has been achieved by using a strain gauge placed on the steel structure of the truck chute, an amplifier and a Programmable Logic Controller. This paper explains the concepts and limitations associated with using strain gauges for ore pass monitoring as well as applying proactive dust prevention and level monitoring interfaces. INTRODUCTION The Henderson Mine, located 69 km west of Denver, Colorado, is an underground molybdenum mine which uses a panel caving process to produce 18,000 tonnes per day currently. This process involves dumping ore down a series of interconnected ore passes leading to truck chutes. Trucks use these chutes to load ore and deliver this ore to an underground crusher. If ore is pulled below the lowest intercept of these ore passes, a ventilation pressure imbalance occurs which generates a large amount of dust on the levels where ore is being loaded into the tops of the ore pass. When a dust event occurs, work must be stopped until the dust settles. Once the dust settles the ore passes must be filled significantly before trucks can start pulling from the corresponding chute. This downtime and unplanned work due to dust can be avoided if the approximate ore pass levels are known. Strain gauges have been installed and tested on a truck chute at the Henderson Mine and the results of these tests have led to a series of concepts in using strain gauges to monitor ore pass levels. This paper explores these concepts and corresponding limitations and explains how the application of ore pass monitoring can be achieved with the use of strain gauges. Ore Pass and Ventilation Pressure Imbalance Overview At the Henderson Mine, there are typically two or four ore passes in different drifts that combine into one bin to create an ore pass complex as shown in Figure 1. When the level of ore is at or below the 7210 intercept (I82W), four drifts have a ventilation connection to each other and the 7655 exhaust level. A “piston effect” is created each time a bucket of muck is dumped down the ore pass. Figure 2 illustrates this phenomenon: as the loader in 621 dumps a bucket down the ore pass, the muck pushes the air in the ore pass down the 82A leg and back up the 82B leg which generates a large amount of dust. The bin regulators on 7655 cannot be opened enough to allow for this surge of air to be relieved onto the exhaust level and the dust ends up exhausting into the 625 and 627 drifts."

Jan 1, 2018

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Lilong Huang, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Graphite is the key raw material of new carbon materials such as graphene and spherical graphite. The size and completeness of graphite flakes directly affect the performance of new carbonaceous materials.The research aims to increase the yield of large flake graphite by way of preventing the flake graphite from being damaged during the grinding process. A series of grinding and flotation studies on the flake graphite samples of Yichang in Hubei Province were carried out by vertical stirred mill . The damage coefficient L characterising the degree of graphite flake fractured and corresponding formula was proposed to determine the quality of the grinding and grinding of the flake graphite. The way the damage coefficient L of graphite flake would be affected if with different mill, different media material and size, stirrer speed were investigated. The test results show that vertical screw stirred mill helps the protection of large flake of graphite as well as the graphite liberation. When grinding to the same fineness, the damage coefficient L of graphite flake is 1.20 for vertical stirred mill, while the damage coefficient is 2.93 for ball mill. Minimum damage coefficient of graphite flake was obtained when using 6 mm polyurethane coated ball as grinding media, under the condition that rotation speed of the stirrer within the range of 100~130r/min. The grade of graphite in the concentrate floated from the ground product was 94.16%, the rate of recovery for graphite was 94.66%, and the content of +0.15mm was 54.83%.1 INTRODUCTION Flake graphite is a very important non-metallic mineral[1,2],and due to its special flake structure, the greater the scale and the higher the C grade, the value of its application is larger too. Therefore, in the grinding of graphite sorting process, We should minimize the destruction of graphite scales.. In this paper, graphite mine in Yichang, Hubei Province was used as the raw material for the study. Rough concentrate with C-grade of 36.49% was prepared by rough grinding and coarse separation. Then a series of grinding and flotation studies on the rough concentrate were carried out by vertical stirred mill , which aims to increase the yield of large flake graphite and to provide technical support for improving the beneficiation process of graphite ore."

Jan 1, 2018