Search Documents

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By Pedro A. Netto, Sergio N. Monteiro, Foluke S. de Assis, Rômulo L. Loiola, Frederico M. Margem

Banana fibers are among the lignocellulosic with great potential for use in polymer composites, such as the variety from the Musaceae family, due to its low density and good mechanical properties. In this work, epoxy matrix composites incorporated with continuous and aligned banana fibers were tested for their flexural behavior. Specimens with up to 30% in volume of fibers were bend-tested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractographic analysis by SEM examinations a moderate adhesion mechanism between the banana fiber and the epoxy matrix. This mechanism is apparently responsible for the improved performance of the composites.

Jan 1, 2015

By N. E. Ablesimov

Electron probe X-ray microanalyser of a coating deposited with "Elitron¬22A" electrospark alloying (ESA) set (anode - Cr, base-catode - chrome vanadium steel) has shown that the zone of phase forming can be divided into three parts: the coating itself, diffusion zone and a thermal affection zone in the base material. Waves of iron and chrome concentrations have been found in the diffusion zone. The authors interprete them as a phenomenon of substance self-organizing in the 30 pill deep diffusion zone, characterized by a change of compositions during the transfer of material from the coating to the base: coating - 20 µm (FeCr2), diffusion zone - 30 µm (Fe3Cr, FeCr, Fe4Cr, Fe2Cr), base - steel (Fe - 87 %, Cr - 12 %, V - I %). This ESA phenomen has been noted for the first time. It may be relative to the phenomenon of periodic formation of secondary products during the mutual diffusion of reacting substances in the case of a one-way reaction. Similar regular structures may appear in the diffusion zone during ESA of vanadium steels with vanadium, manganese steels with manganese and so on.

Jan 1, 1999

By John A. Mavrogenes

The Texaco gasification system developed at the Monte Bello pilot plant efficiently bums petroleum-coke thereby producing syn-gas and electricity. This system produces more electricity than conventional burners, yet the only by-products are pharmaceutical grade sulfur and V -rich slag. Vanadium is known to exist in multiple valence states in compounds which possess a wide range of melting points and physical properties. Consequently, it becomes important to carefully regulate oxygen fugacity throughout the system in order to control vanadium valence state. Vanadium phase equilibria is presently poorly understood, in large part because of the multiple oxidation states of vanadium (-I, 0, +2, +3, +4, and +5) and the difficulty of unequivocally identifying the valence state(s) in many compounds. The operation of these gasifiers at approximately 1400°C is well above the melting point of V20S but considerably below the melting temperature of V02 and V 203. If J02 can be regulated to keep the burner within the V 205 field, slag material would more likely remain molten and more easily flow out of the bottom of the burner. In pure V oxides. the oxidation state is readily determined by microprobe analysis. where V20S (V+5) is 56% V, V02 (V+4) is 61.4% V, and V203 (V+3) is 68% V. However, V valence in multi-element phases (especially phases containing other elements of variable valence) cannot be resolved by microprobe analysis alone. Petroleum-coke gasification slags collected from within the gasifier under different oxidation conditions were studied by electron microprobe analysis (EMPA). X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Raman spectrometry in conjunction with microprobe analysis was found to resolve the valence of vanadium in the phases of these slags. Raman spectra collected from homogeneous single phase V-oxide standards in vacuum at low temperatures (-150°C) yielded peaks characteristic to each valence state. Gasifier slag samples are, however, much more complicated. Oxidized samples contain: fine grained (Ca. Mg, Fe. V) oxide matrix of variable composition, (Fe. V, Ni) spinel. (Fe, AI, V, Ni, Mg) spinel, V205laths, AI-Si glass blebs and Ni sulfides. Reduced samples contain: crystalline Ca-siIicate matrix, subhedral to euhedral (V, Fe, Mg, AI) spinel, subhedral V02, Fe and Fe-Ni sulfides, Fe-Ni alloys, and complex Ca-oxide matrix. The different spinel assemblages, the characteristic V-oxides and the distinctly different character of the matrices makes the oxidized and reduced slags readily discernible.

Jan 1, 1995

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Kanchan Mondal

"Methanol, lower hydrocarbons, CO, and HCOOH formation have been by the reduction of CO2 with H2. Un-catalyzed electro-reduction requires a significant overvoltage. An alternate route has been conceptualized. Production of hydrogen from water can be achieved by chemical oxidation of a metal in water followed by oxidation of the hydronium ion by the released electrons to form hydrogen radical. It is hypothesized that circumventing the problem of the formation of hydrogen molecule is essential while having the hydrogen radical to react with CO2 forming methanol, etc. This may be possible by a bimetallic catalyst acting as a galvanic couple, wherein one metal acts as the electron donor for the production of hydrogen radical while the other acts as a catalyst for the reduction of CO2. This may enhance the reaction rates. The current concept circumvents the need for an external electric field unlike the electrochemical process.IntroductionUtilization of carbon dioxide as a raw material, not only as carbon sources but also as useful chemical feedstock is a more holistic approach to reduce air pollution by flue gases (1-3). Several methods have been proposed to maintain the concentration of atmospheric CO2 or to reduce and recycle it. One of these is the chemical fixations using catalysts. The conversion of CO2 to methanol by hydrogenation over copper containing catalysts is one of the most widely studied subjects in this area. The limitation in this reaction is the low conversion of CO2."

Jan 1, 2008

By Ma Keyi, Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping

"The oxidation of the Multifunctional Electrodeposited RE-Ni-WP- SiC Composites at high temperature is investigated. The results show that during high temperature oxidation the relationship between the mass change of pure Ni , Ni-W-P, Ni-W-P-SiC or RE-Ni-W-P-SiC coating and the oxidation time follows a mixed curve, i.e. it is approximately a linear relationship when the oxidation time is less than 60 mins while it is a power function relationship when the oxidation time is over 60 mins. The order for the oxidation rate of the four coatings is Ni> Ni-W-P> Ni-WP- SiC>RE-Ni-W-P-SiC. The mass change of Ni-W-P, Ni-W-PSiC or RE-Ni-W-P-SiC coating increases exponentially with a rise of oxidation temperature. The high temperature-oxidation resistance of RE-Ni-W-P-SiC composite coating is 3-4 times that ofNi-W-P alloy coating. The cross section morphologies and Xray diffraction patterns indicate that the high temperature oxidation resistance of RE-Ni-W-P-SiC composite coating is better than any other coatings.1. IntroductionWith the rapid development of modem industries the products in engineering industry are continually challenged by the requirements of long-term and stable working at higher temperature, pressure, speed and under adverse conditions. Consequently, the surface properties of the products, such as the resistance to oxidation at high temperature, the resistance to wear and the resistance to corrosion, should be improved continually."

Jan 1, 2000

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004

By Honglei Zhang, Yue Wang, Guotao Xu, Li Liu

The influence of rich oxygen atmosphere on the properties and structure of castables used in the hot wind pipe of blast furnaces was analyzed. Results show that the cold compressive strength of castables is affected by the change of rich oxygen volume in the wind pipe, the bulk density decreases and apparent porosity of castables increases with the addition of rich oxygen in wind pipe. With the addition of rich oxygen, the velocity of heat transfer increase and result of the steel shell become over hot out of safe limit at the thin lining in hot wind pipe.

Jan 1, 2015

By Thomas Havlik

It is proposed to realise the direct leaching, during which will be generated elemental sulfur and not sulfate or sulfuric acid as end product, under conditions that sulfur will not cover the leaching surface and Hot hinder the leaching course. The following improvements have been considered: -use of organic sulfur solvents -ultra high-frequency leaching -ultrasonic leaching -use of surface detergents or surfactants in leaching processes -simultaneously crushing and leaching These proposals are under investigation and preliminary results are promising

Jan 1, 1996

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By James D. Navratil

Ferrites have been used to separate a wide range of substances such as dissolved metal species, particulate matter, and organic and biological materials; they have been used almost exclusively for metal waste treatment applications. The versatility of the ferrite waste treatment technique is evident in the wide variety of application methods. Furthermore, ferrites can be used to remove selected impurities in feed solutions containing metal products requiring purification. A brief overview of ferrite properties and recent applications for metal recovery and waste processing will be presented.

Jan 1, 1990

By Thomas Niehoff, Dave Stoffel

"Energy in the form of natural gas, oil and electricity is expensive and will continue to be a rare resource in the future. Recycling of metals, instead of primary production, is a logical and crucial step towards energy conservation. Energy consumption can be impacted by using advanced combustion systems for metals recycling. Air-fuel combustion has been the conventional method to melt and recycle metals. Global competitive pressures, “greenhouse” gas emissions, and high energy prices force melt shop operations to optimize energy usage and reduce overall operating costs. Oxy-fuel combustion and process technology can be applied to metal recycling operations to meet these objectives. Linde has converted several hundred furnaces from air-fuel to oxy-fuel technology and has extensive experience in optimizing the use of oxygen in furnaces. Additionally, Linde has the process knowledge necessary to avoid costly start-up issues that can accompany the transition to oxy-fuel technology. This paper will describe the benefits and potential issues for conversion to oxy-fuel.IntroductionThe furnace combustion system is the heart of a fossil fuel fired melting process and must be properly matched to the furnace to work as one cohesive unit. Furnaces vary widely in size, shape and features. Rotary furnaces are barrel-shaped and can be designed for tilting or nontilting operation. In a rotary furnace, the products of combustion create a single or double pass through the furnace prior to exiting. Reverberatory furnaces are box-shaped and can also be designed for tilting or non-tilting operation. Reverberatory furnaces are constructed of single or multiple chambers, with or without metal bath movement, and designed for continuous or batch processing. Different furnaces are used for different feedstock materials and products.Furnace combustion systems also vary in many ways. Combustion systems can be of air-fuel or oxy-fuel based technologies, or a combination of the two, resulting in an air-oxy-fuel system. Each of these types of systems has different combustion characteristics which can produce very different results. Here we will describe specific differences in melting processes and their associated energy requirements."

Jan 1, 2009

By Beatriz Ribeiro Nogueira, Vijaya Kumar Rangari, Esperidiana A. B. Moura, Anne Chinellat, Arifa Parveen, Angel Visentim Ortiz

"Composite consisting of ethylene vinyl alcohol (EVOH) with short piassava fibers were prepared by extrusion process and their thermal and morphological behavior were investigated. The EVOH reinforced with 5 and 10 % of pi as sa va (Attaleafunifera Mart) fiber particle, based on the percentage weight ratio (wt %), untreated and treated with a commercial silane coupling agent, were prepared and the influence of fiber loading and the effect of chemical treatment on their thermal and morphological behavior were evaluated by SEM, DSC and TG analyses. Melt flow index (MFI) of the composites have been determined to evaluate the effects of fiber reinforcement on dynamic viscoelastic melt of the EVOH. In addition, piassava fibers characterization by SEM, FTIR, and organic and inorganic composition have also been carried out. The SEM results of the composites showed surface micrographs without microvoids and a good distribution, dispersion and compatibility between the fillers and the EVOH matrix. Concerning the piassava fibers characterization, the results showed that piassava has higher lignin content than cellulose and hemicelluloses, and around 0.7 % of ash with 52 % of silica (Si02). This high concentration of silica is consistent with the SEM analysis of the fiber that showed a large amount of ""silica rings"" encrusted on their surface.IntroductionLately, great worldwide interest has arisen in developing new technologies that enable the use of products with less environmental impact. Effort has been put into seeking natural modifier applications, particularly regarding the use of natural fibers. Special attention has been given to the use of natural vegetable fibers, because of the huge variety of species available. Such vegetable fibers are usually referred to as lignocellulosic materials [1]. This work evaluated the effects of piassava (Attalea funifera Mart.) fiber incorporation in an ethylene and vinyl alcohol copolymer (EVOH). The EVOH belongs to a family of copolymers with excellent gas barrier properties and resistance to organic compounds, which allow its application in different segments, from food packaging to gas tanks. However, EVOH is very sensitive to moisture, and in conditions of high humidity its gas barrier properties, thermal and mechanical properties are affected."

Jan 1, 2012

By F. Patisson

One of the major issues with multiparticle reactors is to handle their multiscale aspect. For modeling, it usually comes to coupling a reactor model (describing the phenomena at the macroscopic scale) with a so-called grain model (simulating the behavior of a single grain or a particle). An interesting approach proposed by H.Y. Sohn (1978) is to use the law of additive reaction times in order to calculate, approximately but analytically, the reaction rate of a particle in the reactor model. Its great advantage, compared to a numerical grain model, is to drastically reduce the computation time, particularly in the case of complex reactor models. This is the approach we retained for modeling the moving bed furnace, a counter-current gas-solid reactor used in the nuclear fuel-making route for producing uranium tetrafluoride from uranium trioxide. The numerical model we developed is 2-dimensional, steady-state and based on the finite volume method. It describes solid and gas flow, convective, conductive and radiative heat transfers, and six chemical reactions involved in the process. The law of additive reaction times is used to calculate analytically the rate of the three principal gas-solid reactions at every discrete point in the reactor. We have demonstrated the validity of this approach by comparing its results with those calculated from a numerical grain model. Also detailed in the paper are the main results of the moving bed furnace model itself and the possibilities of optimizing the process revealed by the calculations.

Jan 1, 2006

By C. L. Kusik

Environmental issues are having a significant impact on how automobiles are designed and ultimately disposed of at the end of their lives. On one hand, increasing concerns about landfill disposal have resulted in greater attention being focused on recycling materials and components from old junk autos. On the other hand, corporate average fuel economy (CAFE) requirements have led to downsizing, use of coatings, materials substitution and other measures that often make recycling more difficult. Automobile makers have responded to Corporate Average Fuel Economy (CAFE) Standards in a variety of ways such as: Downsizing; Designing of more fuel efficient engines; Reducing aerodynamic drag by sleeker body designs; Redesigning by using thinner gauges of coated steels; and Substituting material such as lightweight plastic or aluminum parts for steel. Other driving forces affecting production techniques, choice of materials and recycling issues include the Clean Air Act and its amendments, RCRA. and other environmental legislation. The variety of materials used in automobiles makes the recycling issue extremely complex. Not only does one have different materials used in different automobiles for making similar parts, but changing designs, evolving environmental issues, landfill closures affecting solid waste disposal, and increasing raw material quality standards have created a complex set of dependencies related to materials use and recycling.

Jan 1, 1994

By Yoshimasa Oda

The tank house of Tamano Smelter has adopted a high current density electrolysis operation applying PRC (Periodic Reverse Current) method and before 1991, it had materialized both high production capacity of 161,000 tons/year and high labor productivity. However, recent rapid rise of Japanese currency in foreign exchange market has urged us to further exert our efforts in reduction of labor cost. In order to achieve this goal of labor cost reduction, we have completed, in 1994, our phase four production expansion project which incorporated significant re-structuring of the organization and we have accomplished annual production of 191,000 tons/year. This project can be outlined as increase of number of cells for electrode exchange per day in the commercial electrolysis process to meet the increased number of cells and increase of the capacity of impurity treatment process. These improvements were done with minimum installation of new equipment and facilities and with achievements in efficiency and manpower saving of the existing facilities. Together with these improvements, rationalization in the starting sheet section was carried out by changing the material of mother blanks as well as changing their maintenance procedures. At the same time, the crane in this section was modified to enable automatic operation by a fuzzy control. As a result, we were able to save manpower equivalent to 5 operators in this section. With these improvements, the production capacity was increased by 18% and labor productivity by 25%.

Jan 1, 1996