Search Documents

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual' usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Barry T. Kilbourn

A dominant characteristic of many derivatives of the lanthanides is stability at high- temperatures. Combine this with novel solid-state behavior under those conditions and there is the potential for new materials that can not only improve existing applications but also help create new technologies. These property themes will be traced through new uses ranging from efficient energy generation and raw material conversion to control of environmental emissions and temperature measurement. Conducting ceramics, methane conversion catalysts, sulfur oxide capture agents and phosphor hosts will be described. Some categories will account in the future for significant lanthanide consumption whereas others will remain commercially negligible but technologically vital. All uses will illustrate the versatility of those elements inappropriately termed rare.

Jan 1, 1992

By Alicia Esther Ares, Alex Iván Kociubczyk, Verónica Liliana Scheiber, Roberto Rozicki

In the present research the horizontal solidification of Sn-Zn eutectic alloys (Sn-8.9wt.%Zn) is performed, with two opposite senses of heat extraction. From the process of solidification, the thermal parameters (local solidification time, cooling rates and interphases velocities) and grain sizes from macrostructures obtained were determined. The presence of defects in the solidified samples was analyzed, observing that they occur largely in the collision zones of solidification fronts advancing in opposite directions in the samples.

Jan 1, 2016

By Y. Maeda

Non-ferrous smelting furnaces generally lnstal1 a gas cooling system for treatment of waste gas containing S02. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system Is the best way to cool gas, however this system requires high Initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled Jacket system, are more suitable If the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In addition, the water-cooled Jacket system Is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace. was planned tin our factory and It was necessary to install waste gas cooling equipment. In our case, a water-cooled Jacket system was mo11e feasible because of the low gas volume and high dust content. H was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cool1ed Jacket had been experienced In the past. That is because S02 in the waste gas changed into sulfuric acid which corroded the Jacket material, As the first step, several data from actual usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled Jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, It was installed In a new furnace as a commercial pl.ant. After one year of operation, the initial thickness of carbon steel Jacket remains almost the same.

Jan 1, 1992

By Kinya Atsumi, Kanjana Khunathai, Hisaya Kato, Hidetka Kawakita, Keisuke Ohto, Katsutoshi Inoue

"Crosslinked microalgae were prepared from the residue generated in the production of biofuel, by crosslinking-condensation in concentrated sulfuric acid. These microalgae were tested for adsorption of various metal ions in hydrochloric acid medium. The crosslinked microalgae exhibited high selectivity for Au(III) over other precious and base metal ions. From an isotherm experiment, the maximum adsorption capacity was evaluated to be 3.25 mol/kg of dry gel for Au(III) which was many times higher than that of the original microalgae residue. SEM and X-ray diffraction confirmed the formation of metallic gold particles, suggesting the occurrence of a redox reaction between surface functional groups on the gel surface and trivalent gold ion.IntroductionSubstantial quantities of precious metals are being used by the electronic industry because of their excellent electrical conductivity and resistance to corrosion. In recent years, recovery of precious metals from secondary sources such as electronic scrap [1,2 ], and leach liquors is being favored because of environmental concerns. Of course, recovery is only practical, if its cost is lower than the value of the metals (gold, platinum and palladium) recovered.Traditional methods of separation and refining do not fulfill this requirement. In order to overcome this problem, attempts have been made in recent years to develop new processes including total leaching in hydrochloric acid containing chlorine gas or hypochlorite, followed by solvent extraction and ion exchange [3]. In the new processes, new solvent extraction reagents or ion exchange resins with high selectivity and high loading capacity are used to simplify the process and to reduce the operating costs."

Jan 1, 2011

By Spencer Peng, Larry Wasik, Akram Alfantazi, Michael Mahon

A dynamic simulation of a zinc tankhouse is a potential tool to improve tankhouse production and cost efficiencies. A fully dynamic simulation has potential uses in the design of new tankhouses as well as in the optimization of existing facilities. Equations from previously validated models of a single cell have been adapted to the industrial dynamic process simulation software, CADSTM Plus. Based on the inlet concentration, current density, and electrode setup, the simulation can predict many parameters, including outlet concentrations, flow rates, current efficiency and energy consumption. Multiple cells have been simulated simultaneously, allowing for an entire hypothetical tankhouse to be modeled. The simulation can be used to dynamically predict the conditions in a zinc tankhouse throughout an operation time scale. Further applications of this model include, tracking impurity buildup, modeling of recycle streams and the development of new flow regimes within the tankhouse.

Jan 1, 2012

By Zuomei Jin

The Mineralogical form of Silver in a Ag-rich complex ore was determined. In the complex sulfide ore, acidic thiourea leaching resulted in 35% extraction of silver directly. In the same complex sulfide ore, under the effect of ultrasonic treatment, 65% of silver can be ex¬tracted. After the above ore had been roasted and acidically leached of Zn and Cu, the silver extracted from this Pb-Ag residue was 96.8%. The effets of temperature, thiourea and ferric ion concentrations and partical size were examined. The leaching rate of silver from the Pb-Ag residue was diffusion controlled. The activation energy was calculated to be 10. 49%KJ/mole. The kinetic model for the thiourea leaching of silver from Pb-Ag residue was obtained and is given by, The kinetics of silver cementation by aluminium in thiourea solutions was also investigated. The activation energy was calculated to be 65. 13KJ/mole, which is reasonable fora rate-limiting surface reaction.

Jan 1, 1995

By João M. S. Rodrigues

The use of sandblasting as a treatment method for conditioning anodes for zinc electro-winning was investigated and compared with conventional fluoride preconditioning. The anodes were made from two different lead-based alloys (Pb-Ag-Ca and Pb-Ag). Laboratory results showed that sandblasting and preconditioning both minimize lead contamination in the zinc and sludge generation. Sandblasting was found to have no aggravating effect on the anode corrosion. The sandblasting treatment was tested on Pb- Ag-Ca anodes on an industrial scale in the celJhouse of a local zinc producer. An unexpected finding of the large-scale tests was that the sandblasting appeared to strengthen the anodes, resulting in reduced warping during handling and operation.

Jan 1, 1996

By Jennifer Murphy, Brad S. Schake, Karol Holmes, John R. FitzPatrick, Mike H. West

"The separation and purification of uranium from either nitric acid or hydrochloric acid media can be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps.We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (1 DO-gram) flow experiments, using depleted uranium, were done after the small-scale evaluation of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos.Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process.Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail."

Jan 1, 1996

By Tracy T. Morris, Luis G. Navaro

"Anodic copper slimes produced during the electrolytic refining of copper are routinely batch leached to remove copper. At the Amarillo Copper Refinery, an atmospheric leaching process was converted to an autoclave pressure leaching system to improve the removal of copper, reduce the consumption of oxygen, improve leaching times and enhance tellurium recovery. The benefits of pressurized versus atmospheric leaching of slimes were soon realized by obtaining the desired level of decopperization in a shorter time and with lesser quantities of reagents. The autoclave was designed and constructed with a unique oxygen injection system that enables good control of the leaching process and with no plug-ups. Other features include a mass measuring system that balances the quantity of slimes to be leached to the desired final solution concentration based on initial feed concentrations. The end result was a more efficient and controllable leaching process for removing copper from anode slimes.IntroductionThe electrolytic refining of copper consists of an electrolytic cell filled with a sulfiiric acid based electrolyte and pairs of copper anodes and cathodes. When a current is applied, copper in the anode dissolves and is plated onto the cathode. Impurities within the anode that are more noble than copper do not dissolve and end up at the bottom of the cell and are referred to as slimes. Gold and silver are the main slimes constituents of interest because of their monetary value, but there typically are significant quantities of selenium, tellurium, lead, antimony, arsenic, bismuth, nickel, silica and tin. Copper is also present, usually as a metallic or as a reactant with tellurium, selenium, oxygen or sulfur and can range from 10 to 30% of the slimes fall."

Jan 1, 2012

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. '94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. '97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials' Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By Gaifeng Xue, Xiaohong Xu, Meng Liu, Yijie Song, Guotao Xu, Jixiong Liu

BN (Boron Nitride) based composites were prepared with hot-pressing by using h-BN as main material in ceramic preparation process. The relative density, bending strength, vickers’ hardness, thermal shock resistance, thermal expansion coefficient, thermal conductivity, phase composition and microstructure were tested and analyzed by using modern testing technology. The results indicate that the best formula is B, the relative density is 97%, the bending strength is 260 MPa, the hardness is HV5 343kg/mm2, the thermal expansion coefficient is 2.8×10-6℃-1, the thermal conductivity is 22 W/(m.K) and have no crack after thermal shock for 20 times by water cool. XRD analysis indicates that the main phase compositions are h-BN, β-Si3N4 and sialon. SEM studies show that the grains wrapped up by solid solution.

Jan 1, 2015

By Moo Eob Choi

The reduction of iron oxide particles by hydrogen is one of the most widely investigated gas-solid reactions. The search for new methods for producing iron by the direct reduction of iron oxide has resulted in a large number of exhaustive studies of the various aspects of this reaction. However, previous studies have largely been done with either pellets or lump ores. Little has been published on the hydrogen reduction of very fine concentrate particles smaller than 37 µm (-400 mesh). The kinetics of hydrogen reduction of fine iron oxide concentrates were investigated in the temperature range of 900 - 1300°C.

Jan 1, 2006

By Santo Ranieri

We will briefly review the nickel market in 2003 and look forward to the supply demand balance for the next few years focusing in on the key factors influencing future price dynamics. On the supply side we will examine slated brownfield and greenfield expansions including the Norilsk factor and the small to mid-range 'supply creep'. We will also review the cost side of the industry and what to expect going forward. On the demand side, we will discuss the stainless steel and non-stainless demand, the China factor and the stainless steel scrap supply cycle. We will conclude by pinpinting where the market is on the current price cycle, and where we believe the mid-term direction is headed.

Jan 1, 2004

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999

By Ralph P. Hackl

Bacterial leaching of the Doe Run Company?s cobalt/nickel-containing copper concentrate at low pH (pH 1.0-1.2) and high redox potential (>750 mV vs. SHE) enabled the cobalt and nickel to be preferentially dissolved over copper and iron due to the rapid passivation of the chalcopyrite component. Selective leaching of the cobalt and nickel was achieved with a mesophilic culture comprised mainly of Leptospirillum-like bacteria and Acidithiobacillus thiooxidans. This finding led to the conception of a novel hydrometallurgical process for passivating chalcopyrite and recovering the cobalt and nickel. The bacterial leaching process was tested extensively at the bench and pilot plant scales during 1997-1998. A pilot plant containing four leaching stages processed 30-40 kg/day of chalcopyrite concentrate continuously for 87 days. The cobalt extraction ranged from 75% to 86% during 6- and 8-day retention times respectively, whereas the copper extraction was limited to about 9%

Jan 1, 2003

By Susumu Okabe

Mitsubishi Continuous Copper Converter employs the top blowing lance system for the continuous supply of reaction gases into the molten bath. In order to avoid the excessive refractory wear caused by the melt splash without loss of the reaction efficiency, the furnace design and the blowing condition should be optimized. Empirical equations which correlate the splashing rate on the' side wall with the dimensions of the furnace, lance position, lance size, gas velocity and bath properties were obtained by by the physical model study, and compiled into a computer program. The computer program is effectively utilized for the analysis of the actual operation and for the optimum design of new furnaces.

Jan 1, 1998

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000

By Chris P. Pistorius

Over the past few decades the carbon intensity of ironmaking and steelmaking has been reduced considerably through improved efficiency in blast furnace ironmaking, partial replacement of coke with less carbon-intensive fuels, and increased use of scrap and direct-reduced iron in steelmaking. To evaluate possible further reductions in carbon intensity accurate process information is needed. A preliminary test of the fidelity of publicly reported data as a source of process information is reported here. The sources are industry roundups of electric furnace furnace steelmaking and blast furnace ironmaking (published by the Association for Iron and Steelmaking Technology), and data recorded by the Environmental Protection Agency under the US Greenhouse Gas Reporting Program. From a comparison for an integrated steelmaking plant and an electric furnace furnace plant, it appears that the values from the two data sources are consistent. The comparison does rely on process details such as the quantitative relationship between injected oxygen and carbon emissions in electric furnace steelmaking.