Search Documents

By Allan D. Fernie

Growing interest in pit crushing and conveying is evident from the many articles, technical papers, and new equipment development recently presented. Application of a pit crushing and conveying system is complex, as many factors such as mine design, production scheduling as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1983

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By S. L. Patil, D. E. Walsh

A novel form of calibration of on-line analyzers was implemented. Rather than simple equations, a neural network was used to model the relationship between the scintillation counts (Am and Cs) of an analyzer, and the measured ash for improved on-line analysis of run-of-mine (r.o.m.) coal. Also, a new approach was followed to better evaluate neural network performance. Samples were first divided into various statistically different groups using a Kohonen network. Data was then selected for the training, calibration and prediction subsets, using criteria developed in this paper for sparse data, with representation from each group. A backpropagation based neural network architecture was used in conjunction with quick stop training. Due to noise in the data, the predictions were very good on average, but not individually.

Jan 1, 2003

By Carolina Bruecker, Axel Preusse

"The topic of ground movements in Germany has been studied extensively in the past, especially in the field of active mines. The active hard coal mines were finally shut down in 2018 in Germany and lignite mining is expected to take place only until 2038. The so-called long-term liabilities of the mine operators in Germany include, among other things, the long-term guarantee of stability and thus the monitoring of ground motion.So far, the economic use of underground mining in Germany was mainly the supply of raw materials. In the future, the underground storage of compressed air, methane, or hydrogen will play an important role in renewable energy supply and climate change. Therefore, underground storage space will become more important and spatial planning is essential to ensure availability of safe underground openings for the various options of environmentally friendly energy storage.However, this renewed usage of underground openings may also bring new and sometimes unknown challenges of geomechanical influence. On the one hand, the aftermath of hard coal and lignite mining will be an increasing challenge in mining subsidence engineering. On the other hand, new possibilities due to underground spatial planning may lead to subsidence and/or heaving of the upper surface.INTRODUCTIONBoth hard coal and lignite have a long tradition in Germany. The Prosper Haniel mine in the Ruhr area was closed at the end of 2018 after 150 years, which signalled the end of hard coal production in Germany. Lignite mining still takes place in the Central German, Lausitz, and Rhineland districts. However, lignite mining in Germany is expected to be phased out gradually by 2038 (MDR, 2019). With the closure of these mines, however, mining damage is not over. The long-term consequences of mining, which extend far beyond the closure of the mines, are associated with the liability and responsibility of the individual mining companies. The so-called eternity burdens on the mining company continue to apply. In the field of lignite production, the discontinuation of dewatering and the resulting possible elevations of the surface will be a relevant topic for the future of mine surveying. The same applies to the hard coal mines, which are partially flooded in Germany and therefore require extensive monitoring of soil movements in the future.The discontinuation of energy from hard coal and lignite calls for a change in the energy mix. With the renewable energy revolution in Germany, the focus is on a sustainable and environmentally compatible climate and energy policy based on renewable energies. Sustainable use of the subsoil, both natural and anthropogenically produced cavities, will play an essential role in the objectives of this policy. For example, disused mine cavities can be used to store electricity from renewable energy sources. (Umwelt Bundesamt, 2018) These functions will again cause classical ground movements such as subsidence and uplift, but will also bring new challenges for the mine surveyor. Challenges can be underground cavity exploration in inaccessible areas or legal aspects of underground competition."

Jan 1, 2019

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed.

Jan 1, 1994

By T. T. Gronfors

The excavation process and equipment used for excavation join firmly each other. By changing the process or method, the construction of equipment may be altered essentially. It has been possible to develop a wholy new type of hydraulic boom for tunnelling, when only parallel drilling instead of V-cut is used. The utilization of controlled blasting has made small holes more desirable. So the controlled blasting has had an influence on the selection of drill steel equipment and in this way also influenced the construction of the equipment.

Jan 1, 1970

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Gregg Sherry, Bob Gordan

INTRODUCTION This paper report presents the general case history for the construction of the North Outfall Replacement Sewer (NORS) project. A 1982 City of Los Angeles Wastewater Facilities Plan recognized that a 19.3 km (12¬mile) section of the North Outfall Sewer (NOS), from Culver City to the Hyperion Treatment Plant, was deteriorating and had insufficient capacity. Built in the 1920s of unreinforced concrete and lined with vitreous clay tiles, the originally unventilated NOS suffered considerable corrosion by H2S gas. This caused roof tile and concrete to fall to the bottom of the pipe, which, over the years, reduced the 11.9 M3/S (420 cubic feet per second (cfs)) design capacity of the NOS to a current level of approximately 8.5 M3/S (300 cfs). This worsening condition, thereby contributing to the polluting of Santa Monica Bay. This situation culminated in the State of California Regional Water Quality Control Board, Los Angeles Region, issuing a Cease and Desist Order on January 27, 1986, which required the City of Los Angeles to eliminate such dry weather overflows through a number of prescribed actions. One of these was to construct the North Outfall Replacement Sewer (NORS) by April 1, 1993. PROJECT DESCRIPTION The NORS Project involved the construction of over eight miles of tunnel and related structures. It consisted of a main tunnel conduit to convey sewage to the Hyperion Treatment Plant and four diversion lines connecting the main tunnel to major existing

Jan 1, 1993

By Kerry Spickelmier

With the dissolution of the former USSR and a welcoming of foreign, minerals expertise by a host of developing countries, a "new," more international, world of minerals is open to the mining industry. However, even in the new frontier, the old laws of nature still apply. For those attendees of the 98th annual Northwest Mining convention, the adage "survival of the fittest" commanded particular attention. Miners, engineers, geologists and other unique species traveled to Spokane in December to learn of adaptations they can make to assure, or at least prolong, their place in the mineral industry's land of the living. You have heard the tales of the spotted owl and the desert tortoise, but add to this endangered list the North American mining industry. During a session on international investment criteria, D. Silver of Balfour Holdings (Littleton, CO) blamed excessive environmental regulation, 1872 Mining Law revision and the anti-mining-and-business attitude of our government for migrations from and extinctions within the domestic mining population. "We've been on a death curve for some time," Silver said, "with a lower birth rate and a higher death rate. In the last four years, we've lost 60% of the gold producers in North America, and we're down to 110 companies. The entire industry has lost about 400 companies and is now down to 2800." Unreasonable regulation founded on emotion rather than scientific fact has been the chief cause of death, according to many of the convention speakers. B.J. Kennedy, president and chief operating officer of FMC Gold (Reno, NV), emphasized, "We have accepted a regulatory environment - but we oppose being strangled to death by unreasonable regulations."

Jan 1, 1993

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987

By M. Scherbakov, W. Shi

Abrasion is an important mode of performance for any element of an engineered product that involves material contact for example, a conveyor belt cover. Abrasion resistance is considered to be one of the leading factors in belt cover design and improvement. Various types of abrasion testing are reviewed by and compared to actual belt applications. A new quantitative screening torsional abrasion test is developed by Goodyear to mimic a dynamic contact between belt cover and differently shaped stones of various weights dropped onto belt at any angle, velocity and height.

Jan 1, 2004

By John E. Litz

Since the 1974 introduction of catalytic converters to automobiles in the United States, more than 150,000 kg (5,000,000 oz) of platinum, palladium, and rhodium have been used in the converters. An estimated 8 to 10 million converters are being used annually in the United States, each containing from $5 to $15 of PGM metals. In addition, use of converters is beginning in Europe which will significantly increase the quantity of PGM used. Two basic types of catalysts for converters are being used: pellet and monolithic. The pellets are small, discrete spheres or cylinders of gamma-alumina coated with platinum group metals, Figure 1. The monolithic are honeycombs of a cordierite, A13(Mg,Fe)2Si5AlO18, base coated with gamma-alumina and subsequently with platinum group metals, Figure 2. Pellet catalysts are being used by General Motors and American Motors; whereas Ford and Chrysler are using monolithic catalysts. The table below compares the PGM content and value of the catalysts.

Jan 1, 1986

By Charles W. Merrill

The price records of 7 representative mineral commodities for the 68-year period 1890 through 1957 have been compiled and analyzed for significant trends. When reduced to real prices in terms of dollars of constant purchasing power or to the purchasing power of industrial wages at average rates, a substantial overall fall in prices is revealed. This downtrend contradicts the widely held concept that, heavy drafts on a mineral resource must lead to scarcity, reflected in rising prices. Three metals (aluminum, copper, and pig iron), two fuels (bituminous coal and petroleum)', and two nonmetals (sulfur and cement) have been chosen because of their preeminence in their respective categories, their significance in an industrial economy, and the ready availability of their price records. It might be added that these seven commodities. were selected before any price figures were compiled, none was selected or rejected to substantiate any preconceived notions as to price trends, The overall importance of the seven is demonstrated by the fact that, taken together, they composed over three-fourths of the value of all minerals produced in the United States in 1957. The first step in the analysis was to reduce the price records to a basis for significant comparisons, Two such comparisons have been made: (1) The quantities of each of the commodities that could have been purchased for an average hour's wage in each year; and (2) the unit price of each commodity through hhe years in terms of deflated dollars. These data are set forth in the accompanying table and two charts.

Jan 1, 1959

By Z. T. Bieniawski, Christopher Mark

A new method for the design of long- wall chain pillars, called Analysis of Longwall Pillar Stability (ALPS), is described. The method provides estimates of the relative stability of different longwall pillar designs during all stages of their service life. The key issue addressed by ALPS is the magnitude and time-of-arrival of the longwall abutment loads applied to chain pillars. A field study was conducted and other available field data were analyzed in order to develop an approach for estimating the abutment loads. An example based on longwall experience in the Pittsburgh seam is used to illustrate how ALPS can be used in mine design.

Jan 1, 1986

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By Noel Jarrett

Energy consumption and distribution in aluminum production, conservation accomplishments, and future goals are presented. Electrolysis and electrode manufacture show the greatest promise for major improvements. Means are proposed for reducing waste heat generation in smelting and for conserving energy in anode manufacture by furnace design and substitution of other materials for petroleum coke. Hall-Heroult Process modifications, alternative designs, and the Alcoa Smelting Process are discussed as energy savers. Scrap recycling, more use of aluminum in transportation, and the installation of offshore smelters in less developed countries are shown to be additional means of coping with possible energy dislocations.

Jan 1, 1981

By Kirk Carlton

The Athabasca tar sands of Alberta are an increasingly important source of crude oil for the North American continent. Published figures indicate estimates of recoverable resources in the tar sands at some 300 billion barrels of synthetic crude of which some 86 billion barrels can be recovered by surface mining techniques. At the present time, two commercial plants are in operation, Great Canadian Oil Sands Limited and Syncrude Canada Ltd. Their present combined capacity is approximately 150,000 barrels per day. Some of the factors which will make this oil expensive will be noted here. The location of the present producing plants is 500 kilometres north of Edmonton at an elevation of approximately 320 metres. Recorded temperatures range from +38 to -55 degrees Celsius. Wind velocities are not high but the chill factor with even a slight breeze and minus 40 degrees is very uncomfortable.

Jan 1, 1979

By Jukka Pukkila, Pekka Särkkä

Intensive co-operation between mining industry and mining machine manufacturers during an eight year program Intelligent Mine™ led to a new concept for applying automation technology in mining to improve the productivity and safety of mines. 'The results of the program are now implemented in several mines in Finland and with similar ideas as well elsewhere in the world. The degree of optimal automation of an intelligent mine depends on several technical and economical factors. The basic precondition for the approach is a clear improvement in total economy of the mine.

Jan 1, 2002

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state's population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999