Search Documents

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995

By Clement K. Chase, J. A. Eisele, Paul D. Chamberlain, Terry Laverty, Lee Rice, Larry Sevenker, Albert G. Law, Daryl Tweeton, John Peters

"Name your poison," wrote Forbes, Jan. 3, 1983, in an article describing the plight of much of the mineral industry as it entered the new year. "To ask which (mining) segment is better these days is almost like asking which of several stones would make a better life preserver." "The scene has seldom seemed darker or apparently less promising," said the Mining Journal in June 1982. And the Northern Miner described the year as the third in a "3-year drought which has completely dried up (company) coffers." Thus, 1982 became the worst year for much of the mining industry since the Great Depression. Low prices, commodity surpluses, output reductions, layoffs, temporary and permanent closures, and financial losses made headlines as the general recession continued to hurl blows at an industry facing strong foreign competition, increased government regulations, and plummeting market demand. At fault were tight US monetary policies and the resulting high interest rates that, while forcing inflation to slow, also threw the economic wheels of the country into reverse gear. Automobile production, housing starts, consumer durable sales, and capital spending all fell dramatically. US industrial production fell about 8.5% in 1982, with the GNP dropping by 1.7%. Production Value Not a single mineral escaped this recession. According to the US Bureau of Mines, US nonfuel production value dropped for all but four out of 21 metals and 14 out of 44 nonmetals. Production quantities increased for only gold, lead, and zirconium among metals and for only six nonmetals. Total nonfuel mineral production value dropped a whopping 21% from 1981 levels, the largest decline since 1938 and the first since 1971. Production value was estimated at $20 billion. Metal commodities showed heavier losses than nonmetals-37% vs. 12%-because of their link to depressed automobile and construction industries. Prices From peaks in early 1980, prices of precious and base metals, ferrous and nonferrous metals, and virtually every mineral dropped to 30-month lows in June 1982. Gold dropped to $9.64/g ($300/oz) compared to a high of $27/g ($850/ oz). Silver was quoted below 164/g ($5/oz) versus a $1.61/g ($50/oz) high. Copper was offered at a five-year low of $1.22/kg (55.5¢/lb) compared with a high of $3.30/kg ($1.50/lb). Lead went for 53¢/kg (24¢/lb) versus $1.21 (554). Nickel begged for buyers at $4.19/kg ($1.90/lb) compared to a high price of $7.72/kg ($3.50/lb). Molybdenum was available at or below $8.82/kg ($4/lb), down from a high of $44/kg ($20/lb). Cobalt went for $11/kg ($5/lb) versus $55/kg ($25/lb). Adjusted for inflation, increased currency costs, and currency devaluation, many of these prices are the lowest reached in decades. Financial Profits & Losses Low prices severely impacted companies&apos; earnings, turning profits into sometimes disastrous or fatal losses. Robert Norton, director of the US Bureau of Mines, noting there has been a recession in the mineral industry for years, said, "Profit rates as related to invested capital have been considerably lower (for mining) than those of other industries. Mineral industry profits have been subject to greater cyclical swings and debt equity ratios have been significantly greater than

Jan 5, 1983

By Ulf Georg Gwildis

Overexcavation and ground loss events during pressurized-face TBMadvance in soft ground can result in unplanned deformations above the tunnel and damage to existing infrastructure. Successfully managing the risk of this occurring is crucial for any project in an urban area to proceed. Common risk management approaches include a combination of establishing suitable ranges of TBM operational parameters and using geotechnical instrumentation for deformation monitoring. Another risk management tool is material flow reconciliation, which varies depending on the specified mining method and the equipment choices by the contractor. This paper compares recent and ongoing projects in the Pacific Northwest regarding overexcavation risk management.

Jun 13, 2023

By T. S. Lundström, B. D. Marjavaara, I. A. S. Larsson

"The flow field in a rotary kiln, used in an iron ore pelletizing process, was investigated using a three-dimensional computational fluid dynamics model. The model is isothermal, downscaled and simplified. The objective was to examine the possibility of capturing the unsteady motion of the flame seen in the real kiln. The results from the simulations were compared with recorded images of the real process. The results demonstrate the possibility of quickly getting an overview of the flow field in the kiln. The main, unsteady behavior of the flame was captured. The model may be used as a tool in the ongoing work of improving and optimizing the pelletizing process.IntroductionThe pelletizing process, in which the crude iron ore from a mine is upgraded into pellets, is a process involving large amounts of hot air flowing in complex geometries. Flow control is a crucial factor in this process to maintain high pellet quality. The rotary kiln is one of the last steps in the pelletizing process, and this is where the pellets are sintered to increase their strength and metallurgical properties. The kiln burner produces a flame that supplies the entire pelletizing process with the necessary heat.Kiln burner flames are large diffusion flames arising from a jet of fuel from the burner issuing into a concentric confining cylinder with a surrounding coflow of air, called secondary air. To enable combustion, the secondary air needs to be entrained into the fuel jet. This mixing of the fuel and air is the slowest step in the combustion process and therefore affects the efficiency of the combustion. The rate of entrainment depends on the momentum ratio between the burner jet and secondary air. The higher the momentum ratio, the faster the entrainment rate and, consequently, the faster is the fuel/air mixing.The kiln of interest in this study differs from kilns used in other industrial processes in both geometry and operating conditions. A distinguishing feature is the large amount of secondary air being induced through the kiln hood and then transported to earlier stages in the process as air or exhaust gas. The secondary air therefore has a substantial momentum, implying that the resulting flow field has a significant impact on the mixing and combustion process in general and the flame shape and stability as well as combustion efficiency in particular. A systematic study of the factors influencing the dynamics of the flow field in the kiln, neglecting the combustion, is therefore justified."

Jan 1, 2016

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By Donald J. Olson, Thomas J. Lutzenberger, John Ramage

The North Shore Inline Interceptor, Phase IA tunnel is a 8,550-meter (28,000-ft) interceptor tunnel currently being constructed by Traylor Bros./Frontier-Kemper, Joint Venture, using a 9.8-meter (32-ft - 4-in) diameter Robbins tunnel boring machine (TBM). This tunnel is being driven in Silurian age dolomite approximately 91.5 m (300 ft) below ground surface. Significant water inflows were encountered when the tunnel drive penetrated the thinly-bedded Waubakee Formation. Flow increases approaching 0.75 cu m per min per 30 m of tunnel (200 gpm per 100 ft) have occurred in this formation. After driving approximately 2,285 m (7,500 ft) of tunnel (200 m full face in the Waubakee Formation), total flows exceeded 12 cu m per min (3,200 gpm) with about 5.7 cu m per min (1,500 gpm) entering the tun¬nel from the 200 m (600 ft) of exposed Waubakee Formation. Additional water control measures consisting of increased pumping capacity, increased water treatment capacity, surface grouting ahead of the tunnel, grouting ahead of the tunnel face and panning to improve the working environment for installation of tunnel support, were implemented to deal with the large water inflows. Currently (January 24, 1989), 3,400 m (11,000 ft) of tunnel has been driven, total water inflows are in the range of 11.7 cu m per min (3,100 gpm) with only 6.8 cu m per min (1,800 gpm) inflow from about 1,220 m (4,000 ft) of tunnel driven full face through the Waubakee Formation.

Jan 1, 1989

By Fathi Habashi

SELENIUM AND tellurium are by-products of electrolytic copper refining. Copper anodes contain 0.01-0.2 % Se and up to 0.04 % Te; during electrolysis these deposit as a slime at the bottom of the cell. Such slimes contain 2-15% Se and 0.5-8 % Te, as selenides and tellurides of gold, silver, and copper. The following compounds have been identified in the slimes: (Ag, Au)Te2, Ag2Se, Ag2Te, CuAgSe, Cu2Se, Cu2Te. Anodic slimes from copper electro¬lytic refining are a grayish black powder, minus 200 mesh. When this complex mixture is decomposed in an acid medium, elemental selenium and tellurium can be obtained, while in an alkaline medium, both metals go into solution. Acid leaching The slime is charged in acid digesters of 800-900 lb capacity, heated to 260°C with 78 % H2SO4, for 8-12 hr. During digestion the following reactions take place:

Jan 1, 1970

By B. J. Swenty, J. L. Hubbard, R. L. Peyton

Based on the results of the National Program of Inspection of Nonfederal Dams conducted by the US Army Corps of Engineers during 1977-1981, Missouri was found to have the highest number of "unsafe" dams in the nation. Many of the dams classified as unsafe in Missouri were tailings dams.

Jan 1, 1987

By Charles A. Maliszewski, James M. Galvin, Gerhard Urschitz

With obvious signs of deterioration, the double track, historically registered Bergen Tunnels as part of the commuter rail system in New Jersey waited for rehabilitation for a long time. Serious water in filtration not only caused operational and safety hazards for the electrified rail line but also deteriorated and structurally compromised the tunnel lining. An innovative rehabilitation program was developed to enlarge the tunnel and to provide a new waterproofing system and final lining. For the rock excavation and support New Austrian Tunneling Method (NATM) principles were utilized, while water tightness was achieved by installing a PVC membrane waterproofing system followed by a reinforced cast-in-place final lining. Experienced on-site supervision generated additional savings during construction by streamlining support elements based on geologic conditions encountered.

Jan 1, 2003

By David W. Lillie, Pier A. Abetti

This paper reports on a study of the impact of fast growing new technologies on the market for copper over the next 15 to 20 years. The greatest threat is clearly the inroads of fiber optics on the traditional market for copper in communication cable. Opportunity areas identified include heat pumps, solar power and heat, desalination, electric vehicles and others. The overall impact of new technologies on copper is expected to be modestly positive if adequately encouraged by effective R&D.

Jan 1, 1986

By Richard M. Crowell, John W. Shield, Todd J. Harvey

Facing lower gold prices, gold mine operators throughout the world are seeking ways to reduce costs for treating refractory sulfide ores. Many gold mines, currently producing oxide ores, have underlying refractory sulfide deposits and the operators could extend the mine life by processing these sulfides. Fortunately, oxidation technologies for refractory ores need not be complex nor costly. GeoBiotics, Inc. has developed heap biooxidation technologies (GEOCOAT™) for treatment of refractory gold ores and concentrates. GEOCOATTM uses simple low cost unit operations common to heap leaching of gold and copper ores. The cost effectiveness and flexibility of GEOCOAT™ heap biooxidation allows mining companies to expand operations to include refract01y ore. In addition, GEOCOAT™ can be utilized to supplement or replace existing oxidation processes such as roasting, autoclaving, or agitated tank biooxidation, and to treat a lower resource grade than is currently economic. The GEOCOAT™ technology involves coating sulfide concentrates onto sized support rocks and biooxidizing the sulfides in a heap configuration. After biooxidation the concentrate is stripped from the support rock, neutralized and leached in conventional cyanidation facilities. Ashanti Goldfields Company Ltd. (AGC) produces over 885,000 ounces of gold per year from oxide and refractory ores at its Obuasi operations in Ghana. Refractory flotation concentrates are treated in roasters and in the world's largest stirred tank biooxidation facility. In August 1998, AGC and GeoBiotics jointly constructed and operated a field demonstration heap of the GEOCOATTM process at the Obuasi operations. The heap contained I 082 tonnes of support rock and 125 tonnes of concentrate. The heap was approximately 19 meters square at the base and 3.8 meters high, and ran for 88 days after which the concentrate was reclaimed. Average gold recovery after biooxidation was 91.5% with a NaCN consumption of 8.6 kg/t. Baseline gold recovery by direct cyanidation of the concentrate was 53.8%.

Jan 1, 1999

By Norbert Patzelt

Today the standard method for grinding ore is the wet process. This is mainly due to the fact that the downstream process is wet and considering the total circuit dry grinding is not the most eco­nomical method for the comminution of the ore. Presently in gold ore processing dry grinding is only applied in cases where whole ore roasting is required downstream from the milling plant or if organic carbonaceous matters and sulfides are the primary reasons for the refractoriness. Since dry ore can be fed to the roaster, a dry grinding mill can advantageously be applied. In cases where d1y grinding could be applied advantageously for instance if the ore contains water soluble material and wet grinding is not possible there are serious concerns prevailing within the industty against this technology due to several reasons. Besides of the aspects as discussed later in this paper, there are several plants in operation with little success and considerable operational prob­lems. The reasons for this often lie in the fact that the several com­ponents of such a plant are bought from independent sources with­out considering the system requirements. It is essential that the dry grinding plants require accurate design between drying, pneumatic transport and grinding of the ore in the circuit. This paper will address some of these concerns raised in the industiy from a mill vendor's view along with discussing the development for the selection and configuration of the various dty grinding circuits.

Jan 1, 1998

By A. L. Holmes

Since the 1981 record of 54 mm tons of US fertilizer consumption, grain surpluses in the US have brought about massive acreage reduction programs, decreased fertilizer consumption, and resulting price pressures caused by excess capacity. The strong US dollar that reduced export sales of both grain and fertilizer, and new offshore manufacturing capacity using US engineering/contracting know-how have combined to put US producers of phosphate fertilizers in uncompetitive postures. While recent events suggest the industry may be growing out of this capacity problem, the cost of US phosphates will continue to be disadvantaged by such external factors as taxes, environ- mental regulations, and high power costs. There is no reason to expect help from the government in the form of reduced environmental regulation and taxation. In order to survive, phosphate fertilizer producers will have to develop technologies and adopt strategies that result in world competitive production costs. Current responses to the need to reduce costs include reduced energy costs through cogeneration, innovative reclamation techniques that create valuable land, and in- creased raw material recovery achieved by operator proficiency. While new technology offers long-term benefits for the producer, present efforts are concentrated on more mundane management efforts to reduce costs. Major attention is being given to the problems of labor utilization and productivity. Raw materials suppliers are being asked to renegotiate contracts which more appropriately reflect conditions in an industry operating at about 50% of capacity. Achievements in these and other areas will allow the producers to continue operating until longer term benefits materialize. `

Jan 1, 1986

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By G. H. Schnakenberg

In 1986, the US Bureau of Mines (USBM) embarked on a major research effort to develop technology that could substantially reduce worker exposure to face hazards by simply relocating the equipment operators to an area of relative safety. This reduced-exposure mining system (REMS) research effort enhances the USBM&apos;s ongoing health and safety efforts aimed at reducing and controlling dust and noise and reducing accidents through training and better mining practices. This paper reports on the progress made on the developing research and demonstrates the technologies required for the computer-assisted teleremote operation of continuous mining machines, haulage systems and roof bolting machines.

Jan 1, 1998

By R. J. Gary

Why would a company in its right management mind risk a fuel conversion program on a fuel that can&apos;t burn if it&apos;s too wet or too dry, too hot or too cold, too coarse or too fine, or doesn&apos;t have enough Btu&apos;s to supplement good combustion? On December 23, 1981, two months ago, we finished our first ten years of burning lignite -- this unconventional coal. It is from that experience that I am qualified to address you today. As some of you here probably already know, my company, Texas Utilities Generating Company, has pioneered the utilization of Texas lignite for electric power generation on a large scale, and I think it is fair to say that we have done this pioneering work largely on our own. Some of us feel like Noah did when he built the arc! I have titled this presentation "The First Lignite Decision" because our company was the first to make this major decision in Texas in the mid-1960&apos;s. It was a big decision, and at the time, perhaps a bold one. When you look at the conditions that existed in the mid-1960&apos;s, you can see why.

Jan 1, 1982

By S. C. Sun

The grinding of coals for coal preparation has been studied extensively by previous investigators, but no similar work has been done on coal lithotypes (l-4). However, the different natural breakage characteristics of coal lithotypes have been recognized and utilized by the coal industry (5,6) to develop the Longway Burstlein process (7) for the concentration of macerals(8). The specific objective of this research was to determine the relative grindability of lithotypes, obtained from both anthracite and bituminous coals. An attempt was made to relate the findings, wherever possible, to the chemical and physical properties of the tested lithotypes. Another aspect of this research was to ascertain the size distribution and grindability of lithotypes ground at a various number of revolutions in a Hardgrove mill.

Jan 1, 1970

By T. Janke

When Homestake Mining Company&apos;s Mclaughlin Gold Project was being evaluated for development, it was apparent that recovery of gold from mined ore would be difficult and relatively expensive. The ore was refractory, averaging less than 50% recovery in conventional direct cyanidation milling tests. Extensive testing narrowed the processing choices to either autoclave or roaster oxidation before cyanidation. Roasting was ruled out due to higher capital and operating costs --the Mclaughlin mill would be the first large-scale application of autoclave oxidation of a refractory gold ore.

Jan 1, 1989

By Jürg Künzle

The use of the underground space has been a recurring issue in human history, whereas the reasons for building subsurface structures have changed over time. In the decades to come, the world will be marked by a variety of underground projects never before seen. This paper describes a series of characteristic challenges of designing and building underground freight transportation systems, with reference to the example of Cargo sous terrain, a privately funded underground logistics project in Switzerland. It provides an overview of contracting practices that allow these challenges to be addressed with success.

Jun 13, 2021