Search Documents

By Orville L. Lantto, Bruce K. Cantrell, Keith S. Olson

Approximately 10 to 20 pct of exhaust aerosol mass from diesel equipped vehicles operating without exhaust controls is attributable to particles in the 1.0-10 µm size range. Recent in-mine measurements suggest that, in addition to reducing overall exhaust aerosol mass concentrations, the use of waterbath exhaust conditioners (water scrubbers) may significantly reduce the concentration of diesel exhaust particles larger than approximately 0.5 µm aerodynamic diameter. This implies that a measurement system that discriminates between diesel and mineral dust aerosols on the basis of aerosol size would have different accuracies depending on use of a water scrubber. To test this hypothesis, laboratory measurements were made by the Bureau of Mines to determine diesel exhaust aerosol penetration efficiency through a water scrubber as a function of size and engine operating conditions. Size distributions were determined using a Micro-Orifice, Uniform Deposit Impactor. Concentrations of CO, CO2, NO x, O2 and gas-phase hydrocarbon concentrations were also measured. No significant effect was found for these gases other than a slight decrease in NOx emissions. The water scrubber served as a moderate aerosol control with reductions in mass concentrations of about 29±9 pct under most conditions. This reduction occurred for particles less than 0.2 µm and greater than 0.6 µm aerodynamic diameter. Coal dust aerosols are mostly larger than 0.8 µm aerodynamic diameter. With use of a water scrubber, separating the aerosol into two parts, greater and less than about 0.8 µm aerodynamic diameter during sampling, results in collection of diesel and coal dust aerosol accurate to within 10 pct. Without a water scrubber in operation, such a sampling protocol would only be accurate to approximately 15 pct.

Jan 1, 1991

By Ross W. Smith

Many studies have been made of the microflotation of quartz (1,2,3,4,5,6) and alumina (3,5,6, 7,8) using various anionic and cationic hetero- polar hydrocarbon surfactants as collectors. A few studies have been made on these minerals using amphoteric hydrocarbon collectors ( 9,10, 11,12) and only a few studies have been made on the use of fluorocarbon surfactants as flotation collectors (13,14). The present investigation compares microflotation response of the two minerals in hydocarbon and fluorocarbon collector systems of the anionic, cationic and amphoteric types. An attempt is made to relate flotation response of the minerals to their electrokinetic behavior and the pKa values of the collectors.

Jan 1, 1979

By S. R. Bryan, J. D. Stephens, D. R. Rothbard

The distributions of gold and associated elements in mineral grains from a pyritic gold ore were studied by optical microscopy, and by SEM and SIMS imagery. Products studied were a sulfide flotation concentrate, a calcined sulfide concentrate, a cyanide leached calcine, and a cyanide leached pressure oxidation residue. Individual pyrite grains are compositionally zoned and solid solution gold occurs in some, but not all zones. Most of the gold in calcined products is present as metallic coalesced grains that are smaller than 100 angstroms. Gold lost into cyanide leached residues from the calcines tends to be in “semi-dense” grains that cannot be distinguished from gold-free grains except by SIMS analysis. The gold in cyanide leached pressure oxidation residues occurs as solid solution gold in unoxidized pyrite remnants.

Jan 1, 1990

By Louis Schaarschmidt, Helmut Mischo, Ibrahim Alsalamin

In order to store high-level radioactive waste underground, the German repository concept considers clay, crystalline and salt formations as suitable host rock materials (National Citizens’ Oversight Committee, 2024). The current research projects of the Chair Underground Mining Methods at TUBAF (Technical University Bergakademie Freiberg) in nuclear waste repositories mainly focus on storage within salt formations. In this scenario, the high-level radioactive waste is supposed to be packed into specifically designed containers and then transported underground and emplaced in horizontal storage drifts. The residual temperature of the radioactive waste leads to the question if there are optimization possibilities for waste handling, the storage and the long-term emplacement of such high temperature level waste. A deeper understanding of the heat transmission from the container into the host rock might lead both towards possibly shorter surface interim storage times as well as size optimization possibilities of the repository itself. TUBAF has conducted research that successfully proved that an optimized container positioning yields more favorable thermal patterns and can be achieved with conventional mining equipment.

Feb 1, 2025

By W. G. Willson

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture re-absorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid fuel.

Jan 1, 1997

Several years ago, North American mining companies began to realize they needed to expand their spheres to remain viable. This strategy has been successful, according to Robert W. Schafer. Today, companies from other continents have also recognized the need for an international view for long-term growth and viability, he said. Schafer is vice president for exploration with Kinross Gold. He was the program chairman and moderator of the keynote session at the 1997 SME annual meeting, held in Denver, CO, Feb. 23-27. The theme of the meeting was "Minerals - Serving the Global Community." A record attendance of more than 6,000 people participated in the meeting, which featured 415 exhibitors occupying 582 booths. The title of the keynote session was "Corporate Perspectives on a Global Minerals Industry." Each of the three keynote speakers discussed a different perspective of a global minerals industry.

Jan 1, 1997

By John E. Miller

Unit Rig & Equipment Co., manufacturer of Lectra Haul Trucks, is continually studying methods of reducing the operating costs of large haulage trucks. Reduction of haulage system operating costs is an important goal that equipment operators and equipment manufacturers constantly try to improve on. One of the most variable and important factors affecting operating costs is actual truck operating practices. An examination was centered on methods to optimize truck utilizaion. It was found that a very effective method of accomplishing this goal would be an Automatic Truck Control (ATC) system to automatically control a fleet of haulage trucks in a predetermined pattern. Economic studies were conducted which showed a very favorable reduction in mine operating costs by use of an ATC system. In 1970, Unit Rig & Equipment Company, in conjunction with SAAB-SCANIA began preliminary development of adapting for truck use a proven automated control system previously used for train systems, small trucks, and military target vehicles.

Jan 1, 1979

By A. Juganda, H. PINHEIRO, J. Brune, N. SANDOVAL, G. Bogin, K. Gallagher, F Wilson

The present work discusses the nuances of scaling and flow similarity to develop a 1/40th scale version of a longwall coal mine. Details on the geometric, kinematic, and dynamic scaling of the physical model are presented and discussed. This works also discusses using a 30% CO2 – 70% He gas mixture as a surrogate for methane. It also presents the implications of various Reynolds numbers (ranging from 7,000 to 140,000) and rotation of the shearer drums in the dynamic representation of the airflow and gas mixtures in the physical scaled model.

Mar 19, 2022

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (IIW) integrates various sets of geophysical and geological data to form a network of information which is stored in a database. Computer models are generated from known drillhole information and later correlated with the processed seismic data. Seismic color processing adds another dimension to the interpretation process. Complex trace attributes provide better definition of subtle features not easily observed from black and white sections. Utilizing the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1989

By Earl Parker

The mining/mineral processing industry constantly faces the challenges of handling tons of material in a variety of processes such as crushing, milling, drying, belt transfer and loadout. These processes result in the production of high volumes of dust. A variety of dust detection and collection equipment is needed to properly manage these emissions to remain compliant with stringent air quality and safety requirements. Dust monitoring and bag leak detection can provide ways to reduce air pollutants, make work environments safer and remain compliant with requirements from the U.S. Environmental Protection Agency (EPA), U.S. Mine Safety and Health Administration (MSHA) and U.S. Occupational Safety and Health Administration (OSHA). There are several approaches to monitoring particulate emissions from dust collection equipment. These can include visual inspections, differential pressure gauges or bag leak detection systems. Bag leak detection and monitoring systems can be optical, light based or electrostatic/triboelectric. Recent developments have advanced the efficiency and reliability of electrostatic/triboelectric style monitors. New technological improvements have been developed that are based upon the principal of unifying dc (impaction) and ac (induction) signals and incorporating other proprietary circuit innovations. This higher signal resolution technology results in a more robust and stable measurement for detecting the presence of particulate in a dust collector emission duct or a flow process pipe.

By Bo Hyun Kim, Mark K. Larson

Although techniques and practices of mining are highly advanced, coal pillar bursts or bumps continue to occur. Many uncertainties remain because of the highly anisotropic characteristics of coal seams that are associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous efforts are required to better understand the catastrophic failure mechanisms in coal mines. In this study, 3DEC modeling in conjunction with the Discrete Fracture Networks (DFNs) technique was performed to better understand the true anisotropic behavior of the specimens acquired from a bump-prone underground coal mine. The spatial characteristics of the dis- continuities (i.e., cleats and bedding planes) as input data for the 3DEC model are estimated based on the results of the laboratory tests and field observations. The DFNs explicitly generated the coal seam that was poorly or well cleated, indicating the different spacing between cleat apertures using the probability distribution functions for fracture density (or frequency) and size. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) are also considered by Monte Carlo simulations. Simulation results of laboratory tests using the 3DEC model and DFNs technique agreed well with the results of the laboratory tests. These calibrated results can be used as we seek to evaluate bump risk by modeling at field scale.

Jun 25, 2024

By S. P. Singh

In order to understand the intricate nature of blast damage mechanism and to counter the associated problems, small scale blasting experiments were performed on hydrostone, concrete and granite. This was followed by a 2.4 m x 2.7 m (8'x 9') drifting operation in a quartzite quarry. Interior as well as exterior damage was assessed by different techniques. On the basis of the experimental results, the effect of explosive characteristics on the damage was examined.

Jan 1, 1992

By Lisa Shevenell

Three pits at the Getchell Mine contained water during a hiatus in mining activity (1968-1983). For this period, expected concentrations of As, C1, SO4 and TDS resulting solely 16om evaporative concentration were computed. Computed values are 1.6 to 2.3 times greater than those measured in local groundwaters. However, computed values fix As, SO4 and TDS are lower than measured values in the pit lakes. In some cases, the computed values are only 8% of the measured pit lake values, indicating a major control on water quality via water-rock interactions. In contrast, computed C1 values exceed measured pit lake concentrations.

Jan 1, 2000

By E. Manev

Thin aqueous equilibrium film studies and surface tension measurements on a mixed surfactant system consisting of polyethylene oxide (a model frother) and potassium ethyl xanthate (a model collector) enable the interaction between the two surfactants at the air/solution interface to be elucidated. For the film containing the non-ionic frother, the interface was charged and addition of low concentrations of xanthate acted as a common electrolyte and reduced the thickness of the film inducing rupture. However, at high xanthate collector concentrations, the negative charge xanthate was found to interact with the non-ionic and caused a build-up of negative charge at the air/solution. Higher frother concentrations were necessary to produce non-rupturing thin films upon increasing the xanthate concentration.

Jan 1, 1992

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By Alizeibek Saleimen Nader

The intensive use of computers for mineral application at Serrana's phosphate mine in Jacupiranga, State of Sao Paulo, Brazil, began in the late seventies. The early hardware and software available are described in sufficient detail to allow comparisons between that solution and the new one, based on a personal computer and a new software package - PC MINE SYSTEM from GEMCOM SERVICES INC - that provides full color graphics capabilities plus mine design and planning tools. The process needed for adaptation to the new technology' and its impact on SERRANA S.A. DE MINERACAO are described. Finally, future enhancements to the System and mine control and planning are focused.

Jan 1, 1989

By J. F. Rakszawski, Robert P. D'Orazio

The use of cyanide in the processing of gold has been documented for over a century. It is still one of the more effective methods of isolating gold, as witnessed by the fact that in 1987 cyanidation was used in the processing of 91.5% of the gold produced in the United States.

Jan 1, 1990

By S. W. Mao

Hydrologic and economic criteria figure in many obvious ways in water resources development, but they are rarely linked quantitatively, and most of the applications are pertinent only to the case-in-point. In the preparation of the Regional Plan for the massive program of ground water development in the Punjab, situations have arisen where the choice among two or more alternatives was made by analyzing the economic implications of critical hydrologic parameters. Two of these situations which are of more-or-less general interest are described herein. The first involves basic development policy -- whether ground water development should be based on the demand of the economy, or the conservation concept of safe-yield. The analysis demonstrated that mining of ground water is clearly indicated for areas where alternative supplies are unavailable. The second problem involves integrating hydrologic data into an economic model to determine optimum well design, From an analysis of all pertinent factors, a simple nomograph was derived which can be used to determine well specifications on-site during construction. The nomograph can be modified for use in any alluvial terrain.

Jan 1, 1967

By B. Das, B. K. Mohapatra, K. S. Narasimhan, S. K. Bhaumik

The iron ore slimes (d80 ~ 50 µm) generated at Noamundi iron ore washing plant (TISCO), assaying 57% Fe, 4% Si02 and 8.3% A1203, have been subjected to hydrocyclone studies. The effects of different design and operating parameters have been studied to get a product suitable for subsequent use in the sinter mix. The studies indicate that it is possible to obtain a product containing 64% Fe, 1.4% Si02 and 3.5% A1203 with a recovery of 49% iron. The process involves classification followed by separation in a hydrocyclone. By this method, the overall yield of iron ore production in the plant is expected to increase by 8%. Microscopic examinations and X-ray diffraction studies were conducted to elucidate the mineralogy and liberation characteristics of Noamundi iron ore slimes. This paper deals with the findings of the investigations.

Jan 1, 1993

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975