Search Documents

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola's De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v' at this point is given by IIn this equation p' is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v' (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

By S. S. Mauney

Natural and synthetic colors are used in almost every facet of our daily lives as a means of communication and expression. Natural ochres, umbers, hematites, and magnetites were once used in their crude or semi-processed state for their pigment value in construction products and low-end coatings applications, while yielding, in recent years, to synthetically produced iron oxides for more sophisticated products. Today, through innovative mining, processing, and marketing techniques, natural iron oxide pigments are once again gaining strong inroads into products and markets requiring precise chemical and physical characteristics. With our focus on environmental consciousness and resource conservation, value added natural iron oxides provide an economical and responsible alternative to our color needs.

Jan 1, 1993

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968

By Quispe Mamani, Mayra Casas Azañero

The research is located within Asuncion and Cospan districts, which according to their geological features in contrast with previous studies pointing out Au, Mo and Pb anomalies create an environment of prospective interest. The objective is to use ASTER Satellite Images to identify ore-bearing hydrothermal alteration zones. To do this, processing techniques such as the combination of bands by RGB 943 and 461, band ratio 4/6, 4/5, 5/8 and 2/1 to identify advanced argillic, argillic to phyllic and propylitic alterations. In addition, indices defined by Ninomiya were used as a third technique in order to reinforce the data obtained from the previous techniques. The results in the study area are confirmed by the SAM spectral mapping technique using spectral signatures from the USGS library. Identifying kaolinite, alunite and pyrophyllite, assemblages of the advanced argillic alteration. Concluding in 3 areas of interest with the band ratios, 5 areas with the Ninomiya indexes and 9 areas validated with SAM, which were contrasted in 13 areas of prospective interest with well-marked argillic alteration.

Feb 1, 2025

By B. K. Cantrell, K. L. Rubow

The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8- µm aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 µm diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.

Jan 1, 1992

By C. B. Manula

This paper presents the results of an application of the PSU/USBM Open Pit Materials Handling Simulator (1) to a large stripping mine in the Southwestern Coalfield. The specific objective of the study was to demonstrate the application of the simulator to a complex multi-pit operation, with emphasis on simulating short term and long term production plans recommended for the mine by Theodore Barry Associates (2). Mine Description The mine is located in the Southwestern Coalfield, which encompasses parts of the states of Utah, Arizona and New Mexico. The lease area presently covers 121500 x 103 m2 (30000 acres) in a strip 37.007 x 103 m (23 miles) from north to south and up to 1609 m (1 mile) in width, located at an elevation above 1525 m (5000 ft). Three gently dipping coal seams are present, of which the upper seam (#3) averages 0-5.5 m (0-18 ft); the intermediate seam (#2) averages 0-1.2 m (0-4 ft); and the lower seam (#1) averages 0-2.4 m (0-8 ft). Overburden is mixed sand, gravel, calcareous clay, caliche and sandstone, with calcareous shale and sandstone burden between seams. Where the seams are covered by less than 6.1 m (20 ft) of overburden, they are generally weathered and oxidized and are not extracted. Stripping ratios have ranged from 3.5 to 6.0 with an average of 5.4. All future plans were based on a stripping ratio of 5.3.

Jan 1, 1979

By A. Cecala, J. Noll, J. Hummer

The National Institute for Occupational Safety and Health has observed that many control rooms and operator compartments in the U.S. mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room that had no cleaning system for intake air, a filtration and pressurization system originally designed for enclosed cabs was modified and installed. This system was composed of two filtering units: one to filter outside air and one to filter and recirculate the air inside the control room. Eighty-seven percent of submicrometer particles were reduced by the system under static conditions. This means that greater than 87 percent of respirable dust particles should be reduced as the particle-size distribution of respirable dust particles is greater than that of submicrometer particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced, which is an important component of an effective system and minimizes the entry of particles, such as dust, into the room. The intake airflow was around 118 cfm, greater than the airflow suggested by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) for acceptable indoor air quality. After one year, the loading of the filter caused the airflow to decrease to 80 cfm, which still produces acceptable indoor air quality. Due to the loading of the filters, the reduction efficiency for submicrometer particles under static conditions increased to 94 percent from 87 percent.

Jan 1, 2015

By Brian H. Zelenko, Patricia M. Perry

INTRODUCTION The environmental requirements of the next section of Washington, D.C. METRO subway tunnels present unique challenges to the Contractor. The 14th Street Tunnels contract includes twin 975 m (3200 linear ft) soft ground tunnels. A stringent environmental soil and groundwater monitoring and free product recovery program was specified by the owner. A project-wide dewatering program hinges on satisfactory completion of the environmental requirements. Implementation of the Contractor's environmental program is discussed, including the pros and cons of the program, as they relate to progress of the project. Environmental issues on tunneling projects have become an important part of the urban tunnel construction process. Delays associated with environmental issues can have a major cost impact on tunneling projects. This paper will discuss the first of five Washington Metropolitan Area Transit Authority (WMATA) tunnel and station contracts awarded in 1994. These contracts are part of WMATA's Fast Track Plan to complete the original 166 km (103 mile) system by 2001. As such, stringent environmental requirements have been specified as a part of these contracts to limit delays associated with local regulators in order that the tunnels may be constructed on schedule.

Jan 1, 1995

By Valcana Stoyanova

The distribution pattern, abundance variations and types of polymetallic nodules and associated megabenthic communities in area covers more than 60 000 km2 laid out in the eastern Clarion-Clipperton Zone (CCZ) is presented. Our observations are based on data from 158 boxcore stations collected during the cruise of the Interoceanmetal (IOM) in 2004 on board of RV Yuzhmorgeologiya. Although those polymetallic nodules for two decades been subject to prospecting and exploration studies carried out by IOM, the knowledge of megabenthic communities and their distribution pattern within nodule field was extremely limited. With purpose to evaluate the relationship between polymetallic nodules and associated benthic megafauna, an comparison analyze was carried out in respect to their composition, types, abundance across the studied area owing into account the local particular feature of bottom topography. It is suggested that the nodule-bearing seafloor supported more diverse fauna (higher number of morphotypes) than the nodule-free areas. Moreover, based on correlation between types of nodules and associated faunal morphotypes frequency the apparent relationship is considered. The most abundant megafaunal taxa (between 68 ? 92%) is essentially associated with the occurrence of the diagenetically growth nodules type (D-type and its D1-subtype); the role of the H and HD nodule-types was variable. In respect to the bottom topography, the highest diversity in the structure of megafaunal communities was recorded in the gently undulating plains and on the horst slopes, thus the highest nodule abundance occur on the topographic slopes.

Jan 1, 2008

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By Gerald W. Cormick

In a complex society such as ours, the range of "negotiating" relationships is constantly increasing. These negotiating relationships have emerged as a direct result of the diffusion of power or influence to new sectors and emerging concerns. Even within organizations, the myth of the authority-based heirarchical structure has given way to the reality of constant negotiations between superior and subordinate and with peers in the organizational structure. In the broader context, the corporate organization finds it necessary to reckon and often negotiate with organized employees, suppliers, buyers, government agencies and a range of organized private interests ranging from minority groups to environmental organizations. In response to this diffusion of power and the conflicts which it has engendered, a variety of conflict avoidance, conflict managing or conflict resolution techniques has developed. The purpose of this paper is to attempt to differentiate between some of the conflict intervention approaches which have appeared "on the market", and to suggest three bases for selecting among them: 1. The "role" of the conflict intervenor; 2. How far the conflict has developed; and 3. The breadth and impact of the issues involved.

Jan 1, 1979

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By R. M. Balderrama

Bench-scale laboratory flotation and gravity separation tests were conducted on tailings samples to remove the sulfidic material, mainly pyrite, the source of acid generation. A combination of xanthate collectors, promoters, and frothers were used during flotation. Pyrite recoveries were in the range of 42 to 97%, depending on the tailings being treated. Sulfide sulfur contents of 12.8 to 0.37% in the feeds were reduced to 8.68 to 0.01% in the treated tails. Flotation tests were conducted to evaluate the ARD potential as a function of percent pyrite remaining in the tails. Standard ARD predictive tests were used to evaluate the success of the treatment. In some cases, removal of only 50 to 55% of the pyritic fraction was required, thereby demonstrating the conversion of the waste material from acidic to non-acidic. A laboratory vanning table was used to evaluate the amenability of sulfide-bearing tailings samples to gravity separation. The pyrite recoveries varied from 38 to 86%. The sulfide sulfur content of 12.8 to 0.37% in the feeds was reduced to 6.0 to 0.14% in the treated tails. Predictive ARD tests performed on tailings before and after the gravity removal of pyrite showed that most samples changed from "probably" acid producing to the "uncertain" range. Data reported and analyzed in this paper demonstrate source control for ARD prevention through the removal of metal sulfides from sulfide-bearing wastes using conventional flotation and gravity separation techniques.

Jan 1, 1995

By R. W. Culbertson

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past twenty-five (25) years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated by the Glen-Gery Corporation which is located in eastern Pennsylvania; the National Lime and Stone Company which is located at Carey Ohio; and Holston Defense Corporation which is located at Kingsport, Tennessee. There are, however, numerous operating gasifiers in other parts of the world. Recent events indicate that this situation is changing. The quantity of domestic natural gas available to the interstate market has been declining at the same time that demand for all forms of energy has been increasing. The current potential market for gas with a heating value ranging from 100 to 500 Btu per cubic feet has been estimated at sixteen (16) quads (16 x 1015 Btu) per year. This is expected to grow to twenty (20) quads by the year 2000.

Jan 1, 1978

By D. A. Gulley, L. J. MacDonnell, William A. Vogely

INTRODUCTION Environmental impacts are most commonly associated with air and water pollution. Not- withstanding this fact, to many people the primary disruption caused by mineral extraction is the change in the character of the locale. That is, the environmental impact of mining includes, but is not limited to, the generation of residuals. The dramatic transformation of wilderness or rural land often creates strong reactions to mineral development. Thus, the basic issues of land use management are a useful addition to environmental discussion. In this section, we take up a discussion of federal, state, and local land use management regimes, along with a brief introduction to the potential role of economic analysis. Elsewhere in this volume, land management issues are discussed from other orientations, and the interested reader may wish to look there as well. Locatable Minerals on Federal Lands Legislation and Administration: Access to hard-rock minerals on the public lands is governed by the General Mining Law of 1872. This law declares that "valuable mineral deposits in land belonging to the United States . . . are hereby declared to be free and open to exploration and purchase . . . ." In order to initiate rights, prospectors are required to physically stake claims of specified sizes and shapes following basic procedures set by federal law which may be supplemented by the individual states. Rights to these claims are protected at the exploration stage so long as actual possession is maintained and diligent exploration activity is underway. If a valuable mineral deposit is discovered on the claim, the claimholder earns the exclusive right of possession as against private parties so long as the claim is properly maintained. To maintain this exclusive right the claimholder must per- form $100 worth of labor or improvements, known as assessment work, on each claim every year and make related annual filings with the U. S. Department of the Interior. If the existence of a valuable mineral deposit can be demonstrated, and other legal requirements are met, the claimholder may receive a patent giving full title to the claimed land, including the surface in most cases. The purchase price is either $2.50 or $5 .OO per acre. The Mining Law has remained largely un- changed by legislative amendment during its now more than 100-vear existence. However, while the law itself has not changed, its interpretation and administration have changed considerably. Written at a time of rapid western expansion of the U.S. following the Civil War, the intent of the law was to promote mineral development by inviting unrestricted prospecting and by selling the lands containing mineral deposits at a minimal charge. As federal land policy shifted from one of rapid disposal into private ownership to one of retention and management for a number of uses, mineral patenting requirements have been administered more strictly. The most critical issue concerns what must be demonstrated to establish the existence of a valuable mineral deposit. The so-called "prudent man" standard was established in the case of Castle v. Womble (19 L.D. 455 (1894)):

Jan 1, 1985

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By C. D. Ashley, X. P. Garzon-Villalba, R. M. Lopez, T. E. Bernard

Federal standards for refuge alternatives (RAs) mandate that they not exceed a Steadman apparent temperature (AT) of 95 °F (35 °C) at an assumed metabolic rate of 325 W, a limit that appears to be arbitrary. Occupants in an RA spend most of their time at rest (a metabolic rate less than 325 W), and thermal equilibrium can likely be maintained at an AT > 35 °C. The purpose of this study was to examine the upper limit of sustainable heat stress during 4- and 8-h exposures at rest. Five men underwent five 4-h trials (phase 1: AT range 39 to 49 °C, 90% rh) and five 8-h trials (phase 2: AT range 46 to 56 °C, 90% rh) in a semi-recumbent position. Descriptive statistics for gastrointestinal temperature (Tgi), heart rate (HR), systolic and diastolic blood pressure (SBP and DBP), sweat rate, fluid intake, urine color, urine specific gravity (USG), and changes in body mass are reported. Mean Tgi for all trials ranged from 36.9 to 37.3 °C, and mean HR for all trials ranged from 61 to 75 bpm. To determine the effects of increased heat exposure, differences in heat strain between 4- and 8-h trials were examined via repeated measures analysis of variance (ANOVA). As AT increased, there were no significant changes in ΔTgi and ΔHR from 1 to 4 h in the 4-h and 8-h trials. During the 8-h trials, as AT increased, there was a difference in ΔTgi between 4 and 8 h. In conclusion, there was support for sustainable exposures resulting in no significant increase in physiological strain at an AT greater than 35 °C AT, with a sustainable limit (no increases in Tgi due to increases in AT) below 46 °C AT. Although the participants were not representative of coal miners, the results provide support for sustainable exposures greater than 35 °C AT at an average metabolic rate of 155 W.

By H. I. Meyer

The mine is a large open-pit copper mine located near Tucson, AZ. Mining operations involve shovels digging at relatively fixed locations and haul trucks moving the muck to a primary ore crusher, a primary waste crusher, and directly to waste dumps. The total investment in shovels and trucks is some $100 million. Fig. l is a schematic drawing of the operation. A static method of truck assignment is used; i.e., each driver is given one particular shovel to serve until reassigned by the dispatcher. A dynamic system is one where trucks are reassigned after each trip. The problem is to compute a near optimum assignment of trucks for efficient operation.

Jan 1, 1979

By John G. Viets, J. Robert Clark

A multielement extraction system is being used successfully to provide essentially interference-free geochemical analyses to aid in gold exploration. The Methyl isobutyl ketone-Amine synerGistic Iodide Complex (MAGIC) extraction system separates Ag, As, Au, Bi, Cd, Cu, Ga, Hg, In, Mo, Pb, Pd, Pt, Sb, Se, Sn, Te, T1, and Zn from interfering geological matrices. Quantitative extraction of these elements is accomplished over a broad range of acid normality, making it possible to economically determine all 19 elements from a single digestion or leach solution. The resulting organic extracts are amenable to analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES) and flame atomic absorption spectroscopy (FAAS). For many years the principal shortcoming of ICP-AES was the complex spectral and stray-light interferences that were caused by the extreme variability of components such as Fe. Na, and Ca in common geological matrices. The MAGIC extraction allows determination of the extracted elements with enhanced sensitivity, from a virtually uniform matrix, by ICP-AES and FAAS. Because of its simultaneous multichannel capabilities, ICP-AES is the ideal instrumental technique for determining these 19 extracted elements. Ultratrace (sub-part-per-billion) determinations of Au and many of the other extracted elements can be made by graphite furnace atomic absorption spectroscopy (GFAAS), following back stripping of the extracts. The combination of the extraction followed by stripping of the organic phase eliminates 99.999% of potential interferences for Au. Gold determination by GFAAS from these extracts under the specified conditions yields a fourfold improvement in sensitivity over conventional GFAAS methods. This sensitivity enhancement and the interference-free matrix allow highly reliable determinations well into the parts-per-trillion range.

Jan 1, 1990