Search Documents

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971

By Basar Arioglu, Jaeung Kim, Mehmet Öztürk, Jinmoo Lee, Dongho Lee, Taek-Kon Kim

"Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) includes 3.34 km of a bored double-deck tunnel under the Bosphorus Strait, at a maximum depth of 106 m from the sea level, and 1 km of twin NATM tunnels on the Asian side. The region’s variable geology, hydrology and propensity for seismic activity, combined with high water pressure and large-diameter/double-deck tunnel configuration, make the Eurasia Tunnel one of today’s most challenging and complex projects under construction. Due to the site’s proximity to the active North Anatolian Fault, the tunnel is designed to withstand a 7.5 magnitude earthquake. The tunnel penetrates through both the Trakya bedrock (on both European and Asian sides) and the alluvial sediments at the bottom of the channel. The tunnel is designed to accommodate differential displacements by introducing seismic/flexible joints at proper locations at the transition zones between rock and soft soils. Tunnel fire is also a significant design consideration for undersea tunnel due to that the rubber protecting it in close proximity of the seismic joint should resist a fire for long term safety and durability. This paper mainly focuses on the design for method of tunnel response analysis in transverse and longitudinal direction against seismic demands relating with the seismic joints. INTRODUCTION Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) will build and operate a roadway tunnel under the Borphorus connecting Kazlicesme on the European side and Goztepe on the Asian side, to provide additional road-access across the Strait and consist of three main parts as shown in Figure 1."

Jan 1, 2016

By Paul J. A. Lever, Robert H. King

Human operators, geological conditions, equipment changes, mining sequences, and roof conditions are some of the continually changing operating conditions that drive a dynamic mining environment. These dynamic characteristics make it difficult to automatically analyze mining data because attributes change as the mining environment changes. Mine monitoring systems could provide mine managers with much more useful information than they do presently, if automatic analysis were possible. Automatic analysis of sensor data is also key to autonomous mining systems. This paper describes artificial intelligence (AI) and sensor fusion based sensor data analysis techniques developed over the past four years. These techniques were used to classify machine operating events by continuously monitoring machine power usage in a continuous miner section at an under- ground coal mine. The result is a report similar to an industrial engineering time study. First, numerical pattern classification techniques broadly identify operating events. However, domain knowledge about inter-machine and intra-machine interactions is necessary to identify and refine dynamic event boundaries. By implementing AI and sensor fusion based techniques we are able to classify machine events more accurately and recognize more specific events. These techniques could easily be applied to many different mining sensor data applications

Jan 1, 1993

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By S. E. Phillipson, S. Romberger

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. The geology of the deposit is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks and an extensive crystal-lithic tuff debris apron. The orebody is hosted by intracauldron sedimentary rocks and breccias. Fluid inclusion data suggest that silver, lead and zinc were transported as chloride complexes and precipitated by cooling in veins from <5% (by weight) NaCl eq. fluids at 170° to 215°C. Silver spatially and perhaps temporally associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2002

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By I. H. Warren

Hydrometallurgy has a well-known and established role in the production of manganese metal (1) and manganese compounds, including battery grade manganese dioxide (2). Also, several leaching processes have been developed and applied at various times for the recovery of manganese from low grade ores (3). Recently, interest in the hydrometallurgy of manganese has been stimulated by the problems presented in the processing of sea nodules (4). Fumes and dusts from the ferro-manganese furnaces also offer a potential field for the application of manganese leaching techniques (5). In treating low grade manganese ores a major requirement of the leaching process is that it should dissolve manganese from a mixture of manganese and iron oxides. The most selective reagent for this purpose is ammonium carbamate applied after preliminary pyrometallurgical reduction of the ore (6). Since soluble carbamate complexes of the postulated type (7) are formed by both manganous and ferrous, but by neither manganic nor ferric, ions, selectivety of manganese leaching is achieved by control of the reduction operation to yield, essentially MnO and Fe304? A potential improvement to this two step process would be to simultaneously reduce and selectively leach the manganese in one hydrometallurgical operation. This possibility has been experimentally studied and the results are described below. During the preliminary study of the stability of solutions of ammonium, ferrous and manganous carbamates at elevated temperatures, it was observed, contrary to the observation of Welsh (8) at lower temperatures, that

Jan 1, 1971

By T. W. Peterson

There are two approaches to developing a minicomputer based application for an industrial grinding circuit. Usually, the control program is coded and compilation-debugged on a large-scale scientific computing system or the minicomputer itself if the machine is available. Final debugging and testing must wait for installation and checkout of the entire minicomputer system. Two immediate disadvantages of this approach are the need to obtain, install and check out the hardware before the final debugging stages of program development can begin, and interference with normal mill operation during such final testing. This work reports on an alternative to the usual procedure. Here both compilation and execution bugs are eliminated from the application program before hardware installation by testing the control program against a reasonable dynamic simulation of the entire process. Thus, software development can be completed before the target mini is installed. Such off-line development requires a reasonably accurate mathematical model for the entire process system as well as a suitable simulation package for communication between the simulated environment and the minicomputer application program. Specific data describing the design configurations and dimensions of the mills, cyclones, sumps, pump characteristics and analog controller configuration were supplied by ANAMAX for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure. Steady state ANAMAX data on particle size analysis at various points in the circuit and corresponding values of flow rates, pump speeds, sump heights and slurry densities were used for model parameterization. The preferred operating control strategy - "best grind at operator-set rod mill feed rate" - was set by ANAMAX. An inferential particle size analysis technique using the cyclone cluster as an on-line particle size sensor was used in a novel control strategy_ to achieve the stated objective. Two disturbances common in the ANAMAX circuits - rod mill scoop pluggage and shut down/start up of one of the ball mills - were studied in detail. This report out- lines the steps in system development and testing and the results obtained.

Jan 1, 1974

By Lech Bolinski, Joe Shirley

Over two dozen Resin-in-Pulp (RIP) plants have been in operation in the fonner Soviet Union since the beginning of 1970. Currently approximately 50% of the gold produced in Russia, Uzbekistan and Kazakhstan, which equates roughly to 10% of the total world output, is recovered using the RIP technology. An alternative to activated carbon, ion-exchange resin has several advantages for the recovery of gold. Resins are less prone to clay or organic foul­ing and do not require thennal regeneration. They also have poten­tially higher loading capacities, faster adsorption kinetics, and are more resistant to abrasion. The original Russian RIP process was based on engineering expertise developed for uranium ore pro­cessing and has a few major drawbacks. The biggest problem is an 18-30 day resin stripping process, which results in a huge gold lock-up. The problem was recently overcome by the development of a new stripping technology which cuts the time to 12-24 hours. Currently, there is rather limited practical knowledge of the Russian RIP process in the West, but often Western mining com­panies developing gold mines in the fonner Soviet Union are hard pressed by their local joint venture partners to take a serious look into RIP. It is probably only a matter of time before one of these companies will cross Soviet technology with Western engineering and develop a modem RIP process as an attractive option to the current CIP and CIL technologies.

Jan 1, 1996

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

This study aims to investigate the reduction thermodynamics of ilmenite and pre-oxidized ilmenite, and reveals the isothermal reduction kinetics of pre-oxidized ilmenite concentrate by carbon monoxide. The results indicate that the ilmenite concentrate and pre-oxidized ilmenite concentrate can be selectively reduced by controlling the temperature. The pre-oxidation process leads to the breakage of complex mineral structure, and the formation of porous simple oxides, which is an effective method to increase the reduction and leaching rate. 

By Q. Xu

The adsorption behavior of gold in ammoniacal solutions on to activated carbon has been studied. The gold loading capacity of the activated carbon used in the system and the recovery efficiency by the adsorption were examined. The parameters affecting the adsorption of gold on to activated carbon included temperature, agitation speed, concentration of &apos;cation and anion as well as that of ammonia. It was found that the maximum gold loading on activated carbon used was about 10 kg of gold per ton of carbon. The recovery of gold by the adsorption from ammoniacal solutions was dependent upon the initial gold concentration in the solution. A recovery of 98% of gold was obtained on to the activated carbon under experimental conditions after 120 hour adsorption. It was also found that the initial adsorption rate was relatively fast compared to the whole period of the adsorption. The apparent activation energy for the adsorption was measured to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on activated carbon was controlled by pore diffusion.

Jan 1, 1995

By L. Cheng

Almost all modern cutting bits use a cemented tungsten carbide tip to provide adequate hit life against wear. Laboratory tests by the US Bureau of Mines have indicated that the number of strikes for ignition increased by a factor of three with a new non-rotating bit impacting a sandstone block when the clearance angle was increased by 10°, and that carbide-tipped bits allowed more strikes before ignition than steel-tipped bits by a factor of 7 to 10. Recent field tests in an operating coal mine indicate a dramatic reduction in the frequency of frictional ignitions and improvement in hit life by using a mushroom-shaped hit cap and a larger initial clearance angle. The latter was achieved by increasing the hit attack angle. Improved hit performance through selection of the grade of tungsten-carbide is a com¬promise between fracture resistance and wear resistance. A large clearance angle should he maintained by various techniques, such as a variable attack angle holder, or a reusable hit that can he reground.

Jan 1, 1990

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

By Broderick E. Davis

Each year, about 45 Mt (50 million st) of flotation tailings are discarded in Florida phosphate operations. These tailings only contain about 4% of the phosphate in the ore. However, more than half of the phosphate in the tailings is concentrated in the +600 µm (+28 mesh) size fraction at grades of up to 20% P205. Many phosphate producers have attempted to solve this problem by floating the +425 µm (+35 mesh) flotation feed separately. However, phosphate recoveries in these circuits are typically only 60%. For seven sampled phosphate operations, the phosphate content of the +600 µm (+28 mesh) fatty acid tailings ranged from 15% to 25% P205. In every case, the +600 µm (+28 mesh) fatty acid tailings was higher in grade than the overall flotation feed. Attempts to efficiently recover this coarse phosphate have apparently been unsuccessful at these seven phosphate operations. Recovery of this coarse phosphate would provide an additional 900 kt to 2.5 Mt (I to 2.7 million st) of phosphate annually and add an additional year to the reserves of these important deposits. A typical central Florida phosphate matrix is composed of three different mixtures of minerals. The +1.18 mm (+ 16 mesh) portion is chiefly phosphate pebbles and is beneficiated by sizing. The -106 µm (-150 mesh) portion contains virtually all of the clay minerals and is discarded in the hydrocyclone overflow. The -l mm +106 µm (-16 +150 mesh) material is a mixture of quartz and phosphate minerals.

Jan 1, 1993

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By J. Groff

The Getchell and Twin Creeks mines are located along a north-northeast trending structural zone in Humboldt county, Nevada approximately 40 miles northeast of the town of Winnemucca. Gold mineralization at the Getchell mine is represented principally by sulfide-rich ores, which contain significant amounts of realgar and\ orpiment, with the gold being recovered through processes which involve pressure oxidation. In contrast, oxide ores are currently being mined and processed at the Twin Creeks mine although large reserves of sulfide ores, some of which contain orpiment-realgar-stibnite, have been defined (Bloomstein et al., 1990). The Getchell and Twin Creeks mines represent major gold orebodies but very little has been published pertaining to mineral paragenesis and the characteristics of ore-forming fluids for these deposits.

Jan 1, 1994

By C. W. Hoffman

A fairly recent development in the field of particle separation is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing as such is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages to be gained by the use of probability sizing vs. conventional screening methods are: reduced space requirements for a high capacity unit, fewer moving parts, more versatile product sizing selection, reduced maintenance requirements and lower power consumption.

Jan 1, 1968

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013

By S. S. Szoke

The concrete masonry industry, represented by the National Concrete Masonry Association has significantly expanded its markets since the industry&apos;s inception. The concrete masonry industry has developed and refined concrete masonry units by producing a variety of quality products on automated machines. In the sixties, architectural concrete masonry units gained popularity. In the seventies, the concrete paver market expanded. In the eighties, segmental retaining wall units became popular. The industry continues to research and develop new products and applications for concrete masonry to satisfy the needs of designers, specifiers, installers and owners. Both existing and innovative technologies in the concrete masonry industry are discussed.

Jan 1, 1993