Search Documents

By W. M. Snoddy

The Montana Tunnels diatreme is a low-grade polymetallic ore body containing economically mineable quantities of gold, silver, lead, and zinc. Widely varying gold grades combined with the general erratic nature of the mineralization create a complex sampling, assaying, and ore control problem. In order to maximize productivity and profitability, a variety of procedures have been used. These include differing sample size, frequency and method. In addition, assay techniques have been adjusted and refined to fit specific requirements, the result of which is an accurate, functional sampling and ore control system.

Jan 1, 1991

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By Joseph Cervik

The mined coal bed and surrounding strata are both sources of methane which must be control led during mining. During developmental mining, the mined coalbed is the primary methane source; during retreat longwall mining, the primary methane source is the overlying strata. Underground technology is being developed to control both sources. This technology involves drilling long horizontal drainage holes into the mined coal bed and relatively short holes (less than 152 m or 500 feet) into the overlying strata. Because of the large volumes of methane that flow from such drainage holes and the limited ventilation available for in-mine dilution, underground pipelines are used to transport the drained gas to the surface. Large- scale in-mine degasification demonstrations showed reductions in methane flow of up to 70% during developmental mining.

Jan 1, 1981

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

High-quality sample selection for metallurgical test work is essential to a geometallurgy study, but the large multidimensional dataset makes sample selection a daunting task, as classifying the dataset while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, utilizing custom-built tools in Python to standardize the methodology, saving time and costs. This approach uses the cumulative sum method, principal component analysis, and k-means clustering method to elegantly cluster the data and select representative samples. A case study is used to demonstrate the effectiveness of the methodology by selecting 40 samples for flotation test work.

Feb 1, 2024

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By Rameshwar Sah, L. R. Singh, SIVALINGARAJU BARISETTY, SHYAM YADAV, P. K. Ghorui

Fly ash is a by-product generated from combustion of coal in thermal power plant. Disposal of fly ash is a major environmental concern for the power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, substantial quantity remains unutilized. Silica and alumina are the major constituents in fly ash along with lime. Aluminosilicates and unhydrated lime present in fly ash, in presence of water, undergo a pozzolanic reaction and form cementitious bond which holds the particles together. Bentonite is commonly used as binder in micropelletization of process waste to attain the mechanical strength required for handling and transportation. The bonding of particles by bentonite is a physical mechanism, while fly ash bonding is a chemical mechanism. The present paper deals with the partial replacement of bentonite with fly ash in micropelletization without affecting the quality of micropellets.

Jul 30, 2021

By Nomuqhele N. Nkosi, Yasuo Yabe, Musa D. Manzi, Raymond J. Durrheim, Siyanda B. Mngadi

This study examined rock failure in brittle rocks hosting the deep gold-bearing ore bodies on scales between millimeters and kilometres. This research study is part of the International Continental scientific Drilling Program (ICDP) project, “Drilling into Seismogenic Zones of M2.0-M5.5 earthquakes in deep South African gold mines” (DSeis). The broader ICDP-DSeis project aims include the examination of the extent of damage, the stress state around the fringes of the earthquake, and the potential existence of living organisms associated with deep-level earthquakes. Nevertheless, this study focused on two seismogenic zones – the Cooke 4 mine and Moab Khotsong mine. At Cooke 4 mine, the study examined the evolution of mining-induced fractures (M1-4) occurring ahead of the stope face during the extraction of the remnant shaft pillar. These fractures were monitored and delineated by a dense array of acoustic emission sensors that allowed hypocentres to be located with decimeter accuracy. Using this acoustic emission data, the DSeis team drilled and recovered the fractures, rock breccia and gouge using a sophisticated triple-tube drilling rig.

Apr 26, 2022

By Thomas L. Mell

Continuous processing plants handling liquids have achieved a high degree of centralized automatic control. Many chemical plants are operated from one room, with automatic control of the various process flow rates. These plants know from experience that automatic control can produce higher through-put, better uniformity of product, decreased operating costs and reduction of storage capacity, Plants which process materials in the form of bulk solids have not been able to use control to as great an extent, primarily due to the lack of measuring equipment capable of providing the same types of continuous automatic control available with liquid flow meters. This paper will describe a scale for measuring flows of bulk materials on conveyor belts which is particularly adaptable to remote centralized instrumentation and automatic control, and will also describe some typical control applications. Fig. 1 illustrates the basic method of measurement of this scale. A conveyor belt idler is supported on a rigid carriage which in turn is mounted in two anti- friction bearings on the conveyor stringers. The pivoted carriage is prevented from rotating about the pivot shaft by an electric strain gauge load cell connected between the carriage and a cross support. Increasing load on the conveyor belt increases the moment of the carriage frame about the pivot shaft, and proportionally increases the tension in the load cell. The belt speed is measured by a conventional d. c. tachometer generator driven from a pulley, usually on the return belt. The speed signal from the tachometer generator and the load signal from the load cell are combined to produce a signal proportional to the flow rate of material in tons per hour, or lbs. per foot, or equivalent units, It will be important to remember, in considering various control applications, that the flow rate of material on the belt is composed of these two component signals, namely the weight of material and the speed at which it is moving. The feed rate is then indicated and recorded by a self-balancing potentiometer of the type used for measuring temperature by means of thermocouples. These instruments may also be equipped with integrating mechanisms reading the totalized tonnage over a period of time.

Jan 1, 1958

The estimation of local recoveries, such as the local recovered tonnage of ore and its corresponding grade at a given cutoff grade, is an important problem in a selective mining operation. Multigaussian kriging provides a simple solution to this specific problem. The solution is also complete in the sense that local recoveries are estimated together with their estimation variances. It is thus possible to assess confidence limit intervals on the estimated recoveries. Multigaussian kriging has been applied to the Jerritt Canyon deposit in a most realistic situation. The various steps of the estimation procedure are presented in detail and the potential of the method is demonstrated in view of the results. The obtained results show that the estimated recoveries are in good agreement with the actual recoveries and the actual estimation errors are correctly predicted by the estimation variances. Multigaussian kriging thus appears as a useful and fully operationable tool for the mining industry.

Jan 1, 1986

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By F. F. Aplan, T. H. Wentzler

Limestone is potentially a low cost material for the neutralization of acid mine drainage and other acidic waters such as steel pickling liquor. Unfortunately, when limestone is reacted wit9 these waters containing large amounts of Fe , Fe+3, and SO4-2 , a coating of gypsum and iron hydroxides form on the surface of the limestone inhibiting further neutralization reactions. The nature of these coatings, their morphology, composition and thickness were evaluated using the scanning electron microscope and microprobe, and the kinetics of limestone dissolution was studied both in the presence and in the absence of the reaction-inhibiting coatings. These data were then correlated with the solution chemistry.

Jan 1, 1992

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By James Crosby

The Urad property had been worked intermittently for over 50 years before American Metal Climax (AMAX) started an extensive exploration program on this property in 1961. The detailed studies of the property proved a large ore body of low grade molybdenum ore that could be mined by modified panel caving methods. Mine development and mill construction for a 5000 TPD operation was completed in July 1967. The Urad mine and plant site is located 55 miles west of Denver near Berthoud Pass. The plant elevation is 10,200 feet. The crushing plant is located underground because available surface area is re¬stricted by snow slide hazards. Crushing plant layout and ventilation system design for the Urad mine was based on our operating experience at similar crushing facilities located at the Climax operations. Low speed conveyors of generous width, adequate exhaust volumes at all ore transfer locations, large hoods and good conveyor skirting have made the Urad underground crusher dust control operations very satisfactory. Good maintenance and cleanup of the crusher facilities have made a clean working area with very low dust exposure. The ore from the mine is dropped approximately 1000 feet through ore passes to scraping drifts above the crusher and then transferred to the coarse ore bin by 150 h.p. slusher hoists. A reciprocating plate feeder under the coarse ore bin feeds a 48 x 60 jaw crusher. Ore from under the crusher is conveyed on a 48 in. belt to a vibrating screen where oversize passes through a 7 ft. Standard cone crusher. The crushed ore along with the screen undersize is conveyed on a 42 in. belt to a 1000 ton surge bin.

Jan 1, 1971

By Unto Paakkinen

The testing of different kinds of process flow configurations and cell volumes in industrial scale flotation processes is in general difficult to accomplish and even expensive to perform.1 Also the lack of suitable measuring and analyzing devices often prevents effective comparison of results. Nowadays, the existing flotation processes contain, almost with exception, several return loads which result in difficult control of the process. There exist two good reasons for testing different kinds of flotation circuits at the Outokumpu Oy Kotalahti mine. Firstly it is easy to change the process flow configuration without any additional installation work and secondly, the concentrator is highly automated with magnetic flow meters, on-line analyzer and process computers. In this presentation, open circuit flotation is compared with the classical closed circuit flotation which contains return loads. In additional, the effectiveness of computer control in both cases is estimated and also the effect of cell volume on flotation results is examined.

Jan 1, 1977

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"BACKGROUND The design, development, fabrication, and test of a cryogenic supply for a refuge alternative is part of a larger effort funded by the National Institute for Occupational Safety and Health and managed through a Space Act Agreement with the National Aeronautics and Space Administration at the Kennedy Space Center, FL to create cryogenically based life support equipment responsive to the needs of miners as required by the Miner Act of 2008. This work is done by a joint contractor/NASA team. In particular, the Cryogenic Refuge Alternative Supply System (CryoRASS) serves to provide a respirable air source to miners confined for 96 hours in a mine refuge alternative. This system stores liquid air in a zero-loss cryogenic reservoir (Dewar) until an emergency requires use. The system does not require electric power when in use by miners. Because of the very cold nature of the liquid air, considerable heat stress relief and reduction of humidity is provided in addition to the required replenishment of oxygen. Moderate dilution of CO2 also occurs.INTRODUCTION The design of this new cryogenic refuge alternative supply system (CryoRASS) uses NASA/Kennedy Space Center technology as a development baseline. The design stores cryogenic (liquid) air that is warmed in an air handler box and the resulting gaseous air is introduced to the chamber that not only causes air circulation, but relies upon environmental and human heat to expand the liquid air to a gaseous state. Therefore, the primary benefits of the liquid air source, besides atmosphere maintenance (oxygen), is refuge cooling and dehumidification. This results in reduction of human heat stress and this occurs without the need for electrical power in the refuge chamber. This reduction is a major factor in ""apparent heat"" and the human perception of comfort. Another benefit with introduction of ""air"" vs only ""oxygen"" is the dilution of carbon dioxide. The volume of new air will displace existing refuge air and this air laden with humidity/CO2/low O2 passes out of the refuge relief valves. These RVs should be strategically placed to vent stagnant air preferentially. An initial system test was conducted in our Florida facility in a production 10-person hard chamber for 96 hours. Last year (2014) the system was tested with a 23 person inflatable refuge alternative in Bruceton. For this test, the CryoRASS air handler was redesigned to offer superior characteristics when installed in a Built-in-Place refuge alternative. This report describes the results of the modified system being tested in the Pittsburgh Experimental Mine while attached to a 30 person refuge for 96 (+/-) hours."

Jan 1, 2016

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By Joseph B. Gillenwater

Miss Gertrude Carey lived next to us in Martinsburg, West Virginia for several years. She was a retired school teacher. She was also a cousin to Messers Dan and Joe Baker who owned and operated Standard Lime and Stone Company, a predecessor of Martin Marietta Corporation. She-was well acquainted with the Baker family and their history. Here is one of the legends she told my wife, Jean, and me. The Bakers were originally Tanners. They had a tannery near Frederick, Maryland. There were several boys in the family and when they were grown each man had specified responsibilities. Will Baker was assigned the duty of locating, buying, and transporting tanbark and lime. As he traveled through Maryland, Virginia, Pennsylvania, and West Virginia to locate and buy tanbark, he also talked the farmers out of some pieces of lime, which the farmers had produced in holes dug and filled with layers of limestone and wood. Will Baker took the lime and soaked a piece of hide in the milk of lime. If the lime did not spot the hide, Will Baker would get the farmer to burn some lime for him, and further tests would be made. If these tests were good - the Bakers bought the land. They eventually discovered that the limestone that would make lime that wouldn't spot the hide would also be suitable for producing steel. They began producing lime just outside Harpers Ferry, West Virginia in pots and upright kilns. That stone too small for the kilns was just perfect for railroad ballast. Now you know how "Baltimore Blue Bloods" got together!!

Jan 1, 1979

By R. K. Dunham

It has been estimated that 30% of the United States coal reserves occur in the Western States at depths which would preclude exploitation by surface techniques. Much of this coal occurs in seams considerably thicker than those presently mined in other parts of the country. Recognizing the lack of technology and experience in exploiting the thicker seam range the Interior Department's Bureau of Mines is implementing a major "Mining System for Western Coal," research program which has as its ultimate objective the development and demonstration of underground mining methods and technology for extracting these seams. One investigation, being carried out by D'Appolonia Consulting engieers, under contract to the Bureau of Mines, is concerned with design of an entry system for longwall top slicing of thick western coal seams. This presentation presents an overview of some of the problems which have to be faced in designing such layouts.

Jan 1, 1977