Search Documents

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By Michael F. Gleason

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek Mine In northern Nevada. After the long negotiations reached an impass over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position.

Jan 1, 1990

By Robert E. Baker

Cortez Gold Mines, the United States' third largest primary producer of gold, commenced continuous operations on January 10, 1969. The decision to proceed to production was made in March of 1968 and construction of the mill and stripping operations for the pit began in April and July, respectively. Anomalous conditions on the slope of Mt. Tenabo along the Roberts Mountain thrust fault zone were discovered by the U.S.G.S. while conducting geochemical surveys in the old Cortez silver district. Following the discovery of gold an intensive program of drilling was organized. Drilling outlined an orebody with 3.5 million tons of ore averaging 0.28 ounces of gold per ton. It was on the basis of this reserve that a 1700 t. p.d. cyanide plant was designed. Needless to say, with such a limited ore reserve, economies in design and construction would have to be observed. Cortez Gold Mines is a joint venture with American Exploration & Mining Co., The Bunker Hill Company, Vernon F. Taylor, Jr., and Webb Resources, Inc. , as partners. American Exploration & Mining Co. is the operating partner.

Jan 1, 1969

By M. L. Mellish

In 1989, for the third consecutive year, both the production and consumption of coal in the United States reached record levels. Domestic coal consumption totaled 806.5 Mt (889 million st) in 1989, a 5.4 Mt (6 million st) increase from the year before (Table 1). US coal exporters also had a banner year. For the first time since 1982, exports ex¬ceeded 91 Mt (100 million st). US coal production in 1989 rose by a surprising 27.3 Mt (30 million st), reaching 889 Mt (980 million st) for the year. To a certain extent, the sizable difference between production and demand growth was due to smaller consumer stock withdrawals. Coal consumers withdrew only 12.7 Mt (14 million st) of coal from their stocks in 1989, com¬pared to 22.7 Mt (25 million st) in 1988. Despite strengthening coal consumption, exports, and production, coal prices to all domestic sectors declined slightly during the year. That essentially continued the trend of the past several years. On the labor front, the United Mine Workers of America struck the Pittston Coal Group in 1989. It was a bitter work stoppage that was not settled until February of 1990. This was the first major coal strike since 1985. The strike also precipitated a series of wildcat outages by UMWA members in June and July. At their peak, more than 40,000 UMWA members participated in the wildcat strikes. Except at Pittston, however, most miners were back to work by August. It is estimated that perhaps 4.5 to 9.1 Mt (5 to 10 million st) of coal production was lost due to the Pittston and associated wildcat strikes. However, some of this production may have been recouped by other coal companies not affected by the wildcat strikes, and by the affected companies after the strikes ended.

Jan 1, 1990

By Terry I. Mudder

Metal complexed cyanides in wastewaters form as a result of interactions of free cyanide with metals present in the wastewater and exhibit varying degrees of stability, toxicity, and treatability. Thiocyanate, a pollutant commonly found in cyanide bearing wastewaters, is formed through the interaction of free cyanide with sulfur containing species (i. e. pyrrhotite) both present in the wastewater. In certain industrial processes, such as the beneficiation of gold and silver, cyanide is an essential reagent. Since free cyanide, complexed cyanides, and thiocyanate are potentially toxic to humans and aquatic organisms, these compounds must be removed from wastewaters prior to their discharge into surface or ground waters serving as potential potable water sources, marine or fresh water habitats

Jan 1, 1984

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By J. Y. Kim

Lead ions originating from galena during processing of complex sulphide ores migrate to "cover" the surface of sphalerite and iron sulphide mineral particles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead-activated minerals float in the Cu/Pb rougher circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead-activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide particles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.

Jan 1, 1995

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By Enrique Levy

Central America is graduating this year into large scale mining with the start up of Inco's multi-million dollar nickel laterite processing plant in Guatemala. In the other extreme of the Isthmus in Panama Texas Gulf Sulphur is doing check diamond drilling and foundation test drilling at the Cerro Colorado copper porphyry. The higher price of gold and silver has spurred development and exploration of several small precious metal mines. The purpose of this presentation is to make a brief resumé of the most important mines operating in the area and a list of significant exploration projects. Also, tables will be shown to compare mining codes and taxes. Unfortunately these tables lack information on Panama. Before starting I like to express my appreciation to Kennecott Copper who permitted the use of some of the data compiled by the author on their behalf during the year 1975. Other persons which did not want to be named also have my gratitude.

Jan 1, 1977

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By Kenneth N. Han

The effect of anions such as sulfate, chloride and nitrate on the solubility of rare earth element (REE)-bearing phosphates and fluoro-carbonates was examined using relevant thermodynamic data. The study found that these anions have significant influences on the overall dissolution of REEs from various sources in the aqueous media.

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By Clark B. Risler

Conveyors constitute a critical artery, essential to the successful operation of most ore processing plants. Technological progress is permitting the recovery of metal from low grade ores which previously could not be worked economically. Significant in this progress are improved material handling techniques highlighted by the frequent and successful application of conveyors. From the standpoint of the plant manager the successful conveyors are those he never hears about. They continue to economically transport the loads applied to them, requiring only routine maintenance attention. When such conveyors are subjected to closer scrutiny you will find that they have been carefully selected and engineered to perform the required function under the anticipated conditions. Among the primary elements in a conveyor drive are the electrical motor and the speed reducer. The selection of these elements can be aided by the systematic consideration of several factors. These factors which focus attention on the critical operating conditions, will be individually evaluated and their effect upon the selection of the electrical drive system and speed reducer analyzed.

Jan 1, 1958

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011

By I. Martinez-Dominguez

In September 1992, mining in Mexico was opened again to foreign investment by President Salinas-de Gortari, after thirty years of "Mexicanization" of mining industry which limited foreign participation up to a 49 % (or 34 % in case of national reserves) on a Mexican mining corporation. During said period mining in Mexico was controlled by four or five big mining companies and besides mining production was focused mainly on silver, lead, zinc, copper and fluorspar. Suddenly in middle of a big crisis on Mexican mining industry due to low prices of minerals in the world and also in a period on which it seems that mining industry in the United States and Canada has been condemned to die for environmental reasons, it appears a new Mexican Mining Law to permit foreigners to participate in mining in Mexico' trough Mexican mining corporations that they may control up to 100 %

Jan 1, 1994