Search Documents

By J. A. M. Cano

Pot Grate tests were carried out in the pilot plant at Samarco producing pellets containing SiO2 between 2.0% and 2.2% in a wide range of basicity to be used in blast furnace. These pellets were submitted to tests in Samarco's laboratory and another laboratory in Germany to evaluate the metallurgical properties. The pellets in the binary basicity range (CaO/SiO2) from 0,87 to 0,95 were those that presented the best results in the Pot Grate tests. Based on the results, these pellets are being routinely produced?on industrial-scale confirming the results observed in laboratory tests.?

Jan 1, 1994

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By HONGWEI YANG, Lili Zhang

The oxidation behavior of copper smelting slag under non-isothermal conditions was studied by thermal analysis. The results indicate that the copper slag is mainly composed of fayalite ( Fe2SiO4) and magnetite ( Fe3O4). The oxidation behavior can be divided into two reaction stages with the increase in temperature; the first stage is the oxidation of fayalite to magnetite, and the second stage is the oxidation of magnetite to hematite. The two reaction stages cannot be strictly separated; that is, the reaction of fayalite is not complete, and magnetite has begun to transform into hematite. Based on the TG (thermogravimetric) curves, the ABS (Achar–Brindley–Sharp–Wendworth) differential and the Coats–Redfern integral methods were employed to investigate the oxidation kinetics of copper slag during the continuous heating process. The oxidation of fayalite into magnetite and amorphous silica phases occurs mainly in the temperature range of 673 to 1083 K. The activation energies calculated by the two methods are 193.69 and 195.52 kJ mol− 1, respectively. The reaction is consistent with Avrami–Erofeev equation, and the mechanism of oxidation is random nucleation and growth. The oxidation of magnetite to hematite occurs at 1083–1303 K. The activation energies are 308.79 and 328.77 kJ mol− 1, respectively. The mechanism conforms to the Jander equation and is controlled by the two-dimensional diffusion.

May 16, 2022

By Jens Classen

"GENERAL PROJECT DATA The Sparvo Tunnel belongs to “Variante di Valico” project, a new 65 km highway link between Bologna and Florence, designed to renew the existing A1 route and to connect in a faster way Bologna and Flor-ence. It is composed of a 2,5 km twin tunnel excavated in a complex geological context, characterized by the presence of a series of surface landslides and methane gas. The gradient is 2.6 % and the minimum radius is 1’400 m. The internal diameter of the precast seg-ment lining, equivalent to the final section of the tunnel, is 13.6 m. MAIN TBM SPECIFICATIONS TBM Earth Pressure Balanced S-574 “Martina”, manufactured by Herrenknecht, has a theoretical excava-tion diameter of 15’615 mm. It is equipped with a conical shield 12.2 m long and four back-up gantries. The total length of the machine is approximately 130 m, weighing approximately 4’500 tons. The total installed power is 16’800 kW. The main drive has a diameter of 8’700 mm and has a triple axis roller type bearing equipped with a labyrinth system including 4 sealing lips. TIME SCHEDULE OF INITIAL TBM DRIVE A time schedule of the initial TBM drive is presented in the following list: •,August 25, 2011: start of the excavation of the 1st drive of the Sparvo tunnel •,October 29,2011: stop of the advance of the TBM for gear oil contamination and clogging •,October 29 to December 20, 2011: repair works on the main drive system and modifications on the conditioning system •,December 20,2011 to July 25, 2012: restart excavation of the 1st drive (north tunnel) and its breakthrough •,July 25 to November 29, 2012: 180° turning of the TBM, detailed check of the main drive seal-ing system and fixing problems on gear boxes, race ring, clamping ring and cutting wheel •,November 29,2012 to July 24, 2013: excavation of the 2nd drive (south tunnel) and its break-through •,August 2013 to July 31, 2014: disassembly of the TBM (first 4 months) and standstill of the jobsite for structural issues on precast concrete lining of the tunnel •,July 31, 2014 to March 10, 2015: inspection, dismantling and packaging of each part of the main drive (flange ring, gear box housing and main bearing). The various phases are described hereafter in detail."

Jan 1, 2016

By J. L. Ellenberger, T. Miller

"A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor extensometers were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.To an area-wide failure (Zipf, 2001). In that case, it appears that the pillars had actually remained intact. However, moisture-related yield of the weak floor caused deformations which passed through pillars and into the roof, triggering roof collapse around the intact pillars (Esterhuizen et al., 2011). This previous case and the case presented in this study, while not identical, both demonstrate that weak floor and/or bands within pillars can be a significant factor leading to instability."

Jan 1, 2015

By Siqing Liu

A low-grade cassiterite-magnetite ore from Sichuan province, China, is finely disseminated, assaying 0.39% Sn and 23.20% Fe, respectively. Mineralogy studies show that the fine-sized cassiterite is mainly disseminated in iron minerals and gangue. Moreover, the embedded size of cassiterite is very fine and must be ground to -0.01 mm to achieve a degree of liberation of about 90%. Therefore, fine grinding needs to be conducted to get a high quality tin concentrate and a great loss of tin cannot be avoided when treating the ore by gravity concentration. Based on the above facts, a two-stage separation, with a low intensity magnetic separator and a shaking table, was selected to test the ore. Compared with other similar plants, a relatively good separation has been achieved. Three acceptable products for smelters were obtained as following: iron concentrate assaying 61.69% Fe with a recovery of 75.09%, tin concentrate assaying 27.21% Sn with a recovery of 56.97% and a sulfur concentrate assaying 40.86% S with a recovery of 32.03%, respectively.

Jan 1, 2011

By James E. Jones

The coal mining industry is being called upon to vastly increase production in the coming years. Many mining operations will have to prepare an environmental impact report of some kind and all will have to comply with various types of environ- mental regulations. Therefore there is a great need within the industry for access to environmental data, information, and literature. This paper discusses the informational resources available, the current lack of access to these resources, and the Environmental Data, Information and Literature (EDIL) Bank of the Kentucky Institute for Mining and Minerals Research. The bank's major emphasis concerns the environmental, social and economic aspects of producing clean solid, liquid, and gaseous fuels from coal. The data bank promotes information interchange between other related governmental and private projects and the energy development community.

Jan 1, 1976

By Edward Holloway

The basis for the selection of the ultimate pit for an open-pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau while the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-mak-ing range is significantly reduced and the process for select-ing the ultimate pit becomes more consistent, replicable and defensible. The technique outlined in this paper provides an approach to including risk in the process used to select the ultimate pit.

Jun 1, 2024

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.

By K. Bunney

A high-pressure laboratory elution rig was commissioned to simulate industrial Zadra and AARL elution conditions for the stripping of gold, silver and mercury from loaded activated carbon. It was found that cyanide was essential for the efficient elution of both mercury and silver, while gold was found to elute most effectively in hot, low-ionic strength solutions. Therefore, the standard AARL-type elution, which implements a cyanide soak and water elution, results in a lower recovery of mercury and silver from the carbon. No single set of conditions was found whereby gold, silver and mercury can all be effectively eluted in a single step. However, sequential elution conditions can efficiently recover all metals and provide a potential approach for separating these metals.

Jan 1, 2010

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By Sunfangze Liu, Xumeng Chen, Yongjun Peng

Efficient separation of naturally hydrophobic gangue, such as talc and carbonaceous materials, from sulphide minerals in flotation is becoming a significant challenge in many processing plants due to the need to process lower grade and more complex ores. Considering the hydrophobic nature of these gangue minerals, prefloating them at the beginning of the flotation circuit in the absence of collectors and rejecting the concentrate is a common practice to remove these gangue minerals. However, sulphide minerals, such as chalcopyrite, can become naturally floatable due to surface oxidation and therefore may float together with naturally hydrophobic gangue. In this study, a new approach was developed to maximize the prefloat of hydrophobic gangue while minimizing the loss of sulphide minerals. The new approach introduced a prefloat cleaner stage where sulphide minerals recovered to the prefloat concentrate was depressed and separated from other hydrophobic gangue minerals at a low pulp potential with the prefloat cleaner tailing fed back to the main sulphide flotation circuit. Flotation tests were conducted using chalcopyrite and organic carbon. The results show that the proposed approach can significantly reduce the loss of valuable minerals in the prefloat flotation without affecting the reject of naturally hydrophobic gangue. Applying pulp potential control at the prefloat cleaner flotation stage also reduces the consumption of reducing agents while minimizing the effect of reducing agents on downstream rougher flotation.

Nov 23, 2020

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971