Search Documents

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By J. H. Schuenemeyer

Uncertainty estimates on coal resources were computed as part of the U.S. Geological Survey’s National Coal Resource Assessment study of more than 60 coal beds and zones in the Appalachian Basin, the Colorado Plateau, the Gulf Coast, the Illinois Basin, and the Northern Rocky Mountains and Great Plains. The estimates were made to provide zone specific measures of uncertainty on the historical categories of geological assurance, namely measured, indicated, inferred and hypothetical. Previous estimates were based solely upon distance from a drill hole. These new estimates incorporate site-specific variability and spatial correlation and indicate that there is considerable difference in variability within and between regions. Uncertainty estimates for the measured category are discussed in this paper.

Jan 1, 2001

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

By M. Paul

"INTRODUCTION In 1990, the uranium production of SDAG Wismut in East Germany was stopped. 45 years of inconsiderate destructive exploitation had scarred both landscape and nature. With the “Wismut law” which came into force in December 1991, the Federal Republic took responsibility of the remediation of the legacies from former uranium ore mining and milling in Saxony and Thuringia. A unique opportunity turned out in order to remove environmental damage, to enhance the life quality of the local population, to shape new landscapes and to advance the economic restart. (1) The results of nearly 25 years of remediation activity are evidence that this opportunity was used at all former SDAG (Sowjetisch-Deutsche Aktien-gesellschaft) Wismut sites. The reference project “Wismut“ has evolved into a joint project of all parties involved and radiates beyond the affected regions. This is particularly reflected by the Know-how transfer starting from Wismut and the increasing activities for third parties abroad.WATER MANAGEMENT AT WISMUT REHABILITATION Within the Wismut project, water management and conventional technical water treatment are by far the most cost-intensive long-term tasks of the remediation programme. Over the medium term, there is no viable alternative to the operation of active systems to catch and treat contaminated mine waters at the Ronneburg, Schlema, Königstein, Pöhla, Seelingstädt and Helmsdorf sites. Based on the status quo, this paper outlines the key issues of the Wismut GmbH water management strategy over the medium and long term. It is focused primarily on achieving protection goals for potentially impacted water bodies in the surroundings of Wismut sites and on optimising associated remediation expenditures as well as on creating the prerequisites for achieving low post-remedial care and maintenance or walk-away system status over the long term. (2) The applied mining practices during the active SDAG Wismut period have not been up to the high standards of modern mining operations and their requirement to leave former production premises and deposited residues in a condition that was not only physically but also chemically stable. Rather the emission of mine and seepage waters laden with high acidity, metal and salt content is a frequent corollary and difficult legacy of historic mining and processing operations (4, 5). As a consequence, the control or mitigation, respectively, of environmental impacts associated with contaminated mine waters ties up enormous public resources worldwide (6, 7)."

Jan 1, 2016

By L. Harris

The Yanacocha project is the first foreign investment in Peruvian mining since Cuajone during 1976. Three years after the project began, it has become the largest producer of gold from heap-leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha SA (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits. And it has attracted the interest of foreign investors in Peru’s mineral resources. Construction began on Aug. 1, 1992. The first gold bar was poured on Aug. 7, 1993 from ore from the Carachugo Mine. During 1993, Minera Yanacocha produced 2.5 t (81,000 oz) of gold and 9.4 t (304,000 oz) during1994 (40% above budget). Production was expected to exceed 15.5 t (500,000oz) during 1995 with the start-up the Maqui Maqui Mine.

Jan 1, 1996

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By S. Dixon

The Phelps Dodge - PD/PERI Heap2D Model is a phenomenological stockpile leaching model that has been used to investigate the best operating practices for leaching chalcocite. The model was used to investigate the interrelationships of raffinate application rate, aeration rate, raffinate iron grade, acid cures, lift height, crush size, bulk density, air injection spacing and raffinate drip emitter spacing.

Jan 1, 2006

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By S. Hardcastle

Tele-remote operation of production equipment from surface will change the design criteria for underground mines. And for ventilation, with machine operators on surface, conventional planning to dilute and remove pollutants can become redundant. Natural Resources Canada with industrial partners are investigating what will be the new environmental design criteria. Additional complications include new mining equipment being designed without standard services and mines’ desire to eliminate conventional auxiliary ventilation. Findings to date show the cooling of equipment’s hydraulic systems to be the most demanding element, especially in dead-ends and when stationary. Consequently, revised ventilation based heat control strategies for equipment are being developed for the automated mine of the future.

Jan 1, 2001

By E. M. Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the disabling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article. Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety.

Jan 6, 1986

By O. N. Sikazwe

The Nchanga Cu-Co ore deposit of the Zambian Copperbelt, is hosted in Neoproterozoic siliciclastic-carbonate sedimentary rocks, and it consists of two orebodies: the Lower Orebody (shale) and the Upper Orebody (arkose). Refractory Cu ores present in the Upper Orebody comprise 150 Mt with average 0.87% Cu, and are characterized by inadequate recovery of copper by leaching. This materials characterization study, conducted on refractory ore samples from the Upper Orebody using optical microscopy, QEMSCAN®, and microprobe, has shown that copper occurs mainly in biotite, phlogopite, malachite, pseudomalachite and goethite. QEMSCAN® has quantified the abundance of each phase and total Cu deportment in each phase.

Jan 1, 2008

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

The La Colosa, Colombia porphyry gold deposit is currently in the pre-feasibility stage. This large deposit has many types of gold mineralization: native gold, electrum, and tellurides. These variations in the gold mineralization lead to variability in the gold recovery. The final process flowsheet may include gravity concentration with cyanide leaching. Metallurgical testwork is utilized to identify the zones of ore that may be problematic to recover. To help select the samples that represent the fluctuating variability zones, geometallurgical models are constructed using mineralogy and geology data. These zones are then wireframed and compared to the geological and structural models for spatial correlation. Samples for the variability testwork will be selected from these different zones to identify and analyse the effect the different gold mineralization types have on the recovery. By using geometallurgy to aid in the sample selection for metallurgical testwork, the variability in the ore body can be understood and constrained to aid in process optimization.

Feb 27, 2013

By Dennis A. Swyt

In current post-industrial America, U.S. manufacturing is undergoing major changes both in the technology of its production and in the size and composition of its workforce. At the same time that computers and robotics move the shop floor toward becoming the unmanned "factory of the future" [1], they increase the need within the overall production enterprise for new types of technicians and engineering professionals [2]. Based on previous works which examined, first, the evolution of the technology of manufacturing toward the flexibly-automated factory of the future and, second, the technical- professionalization of U.S. manufacturing sectors [1,3], this paper looks briefly at the workforce of the U.S. metals industry.

Jan 1, 1989

By E. Iasillo, R. R. Carneiro

Independent of the method chosen to forecast production, an accurate method to project metal extraction is needed in order to accommodate leach cycles that exceed leach data on hand and thus be able to accurately forecast production. Metal extraction data must be developed for each ore type identified in the deposit in order to apply the correct rate of leaching when a specific ore is being treated. Curve fitting is used to model the rate of disengagement of metal into the pregnant solution. This paper provides a description of a curve fitting algorithm developed by Mr. John T. Bartlett, inventor of the METSIM™ process simulation program. A methodology is provided by which the metallurgical data developed is evaluated to determine if accurate projections may be made from the data. A criteria has been developed to help determine when a column experiment may be terminated.

Jan 1, 2001

By Hongjie Yang

The No. 10 metro line of Shanghai city is 36 kilometers in length and will pass through the operating airport runway by using tunnel boring machine with earth pres-sure balance mode. Although there are examples through world that tunnels pass through airport runway and tunnelling underground is not a difficult undertaking technically, there is rare experience in China for the similar projects especially in Shanghai saturated soft soil region. Shanghai soft earth is famous for its high compressibility, high rate of water content, weakness in strength, large deformation and different characteristics in earth strata. Besides, the whole construction process will be under ultra-large airplane dynamic load on the surface ground over the tunnel, which increases the risks of construction process. This paper evaluates the feasibility of building the metro tunnel under such an extremely serious condition, especially the subsidence of ground surface caused by advancing of tunnel boring machine, which also is the most important control target for the safe operating of the runway. Furthermore, this paper discusses the effective measures to keep the settlements in the permissible level during the whole working period for the tunnel from aspects of plan, design and construction.

By M. Menéndez

Enhanced gravity separation appears to be one of the most promising methods for processing all types of <200-µm coal feeds and tailings. Systems based on this technology are reviewed, and the results of investigations based on C900 Multi-Gravity Separator tests conducted to assess the treatment of <200-µm, extremely difficult-to-wash coal settling pond tailings are presented. Multi-Gravity Separator processing tests of ultra-fine tailings with a high clay particle size content (22.6% <10 µm and 60.1% <40 µm) and a 69.56% ash content show that this material can be effectively treated after desliming (<10 µm) of clay-size particles to produce a coal with a 20.6% ash at a separator combustible material recovery of 69.3%. Desliming is shown to be critical in reducing coal ash content and combustible material recovery. Similar improvements are anticipated in the recovery and separation pro-cesses for other enhanced gravity separation systems from the desliming of feeds. Although not a conventional form of treating Multi-Gravity Separator data, the existence of well-defined polynomial relationships based on the product of drum shake amplitude and shake frequency relative to product coal recovery, product ash content and yields at varying wash water flows is demonstrated. Low-amplitude and intermediate- to high-frequency bed agitation are shown to produce optimum ash reduction results.

Jan 1, 2007

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013