Search Documents

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By F. M. C. C. Vieira

The DEEPMINE Research Programme sought to develop the technology and competence to mine gold safely and profitably at depths of 3 to 5 km. Among the many issues addressed was the stability and support of rockpasses at ultra-depth. It was found that high virgin and mining-induced stresses could cause the walls of rockpasses to spall, leading to the deterioration and failure. A comprehensive programme of numerical modelling was conducted to investigate alternative mining layouts and sequences to ameliorate the problem.

Jan 1, 2005

By K. Schwerdtfeger

Data are presented on the effect of iron oxide on the electrical conductivity of CaO-SiO2-FeO-Fe2O3melts, and on limiting current and impedance in direct current or alternating current charge transfer at iron electrodes. The strong influence of iron oxide content can be utilized for in situ determination of total iron oxide content and Fe3+/Fe2+ratio. The possible probe designs are presented and the principles and procedures of the measurements are explained. Keywords: in situ probe for iron oxide determination in steelmaking slags, electrical conductivity of CaO-SiO2-FeO-Fe2O3slags, direct current over voltage and alternating current impedance at iron/slag electrodes.

Jan 1, 2004

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

By P. G. Gresse

The Orange-Vaal River system is known to be the primary secondary source for alluvial diamond deposits in the northern Cape and along the west coast of Namaqualand. The higher order sources for diamonds contained within this system are still not defined entirely to satisfaction, but certainly include kimberlite pipes exposed in the catchment regions of these rivers. The focus of alluvial diamond mining along the Orange-Vaal system recently changed from the traditional areas in the upper catchment regions?the Barkly West, Christiana, Bloemhof, Wolmaranstad, Schweizer-Reineke region, and the lower regions near the mouth of the Orange River at Baken, Alexander Bay and Oranjemund, to the area between Douglas and Prieska?the so-called mid-Orange region (Figure 1).

Jan 1, 2003

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By A. Ebrahimabadi

Roadheaders are very versatile excavation machines used in tunnelling, mine development, and mine production for soft to medium strength rock formations. Performance prediction is an important factor for successful roadheader application and generally deals with machine selection, production rate and bit consumption. Among many different parameters, brittleness is also one of the material properties related to breakage characteristics and can be used as a cuttability parameter from a mechanical excavation point of view. The main objective of the research study is to contribute the brittleness of rock excavated to construct a new empirical equation for predicting the performance of roadheaders in different material and operational conditions. In this regard, a new performance prediction model for medium duty roadheaders based on a brittleness index (BI) is presented. In this study, rock mass brittleness index (RMBI) is defined in order to investigate the influence of BI on roadheader performance. RMBI is an index which can be used to relate the intact and rock mass characteristics to machine performance. Results demonstrated that RMBI is highly correlated to instantaneous cutting rate (ICR) (R²=0.94). Moreover, through the further analysis and normalization, the pick consumption index (PCI) was introduced as a parameter having a good relation with pick or bit consumption rates (PCR) (R²=0.79). Finally, the new predictive models for ICR and PCR showed very good correlations with the actual measured values. Keywords Performance prediction, roadheader, brittleness index, mechanical excavation.

Jan 1, 2011

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

By J. P. Gous, J. J. Sutherland

"Transalloys is a silicomanganese (SiMn) producer located in South Africa, and uses only local manganese ores to produce SiMn alloy. The plant operates five open submerged arc furnaces (SAFs) with an annual capacity of 180 000 t of saleable SiMn.Maintaining tap-holes is critical for effective furnace operation, allowing proper drainage of the furnace with minimal operator interference. Using a claygun and drill arrangement installed at each furnace, tapping occurs every four hours. Tap-holes are maintained through mickey replacement and brick repairs. Three furnaces have SiC tap-holes and two have graphite tap-holes.This paper gives a review of SAF operation, furnace and tap-hole design, daily tapping operation, and maintenance practices for repairing tap-holes.IntroductionDefining tap-hole life cycle, Steenkamp et al., (2016) highlighted four main steps: installation during furnace relines, day-to-day operations, tap-hole maintenance, and tap-hole repair. The authors argued that the design of the tap-hole area should allow for all four stages in the tap-hole life-cycle. Design principles for each stage were presented using silicomanganese (SiMn) production as a case study. Here we present a further analysis of the case study by providing practical examples of how the tap-hole life-cycle is managed at Transalloys during the design, operation, and maintenance of submerged arc furnaces (SAFs) applied in the production of SiMn.BackgroundTransalloys is the largest producer of SiMn in Africa. Its smelter complex is based outside the town of eMalahleni, in the Mpumalanga Province of South Africa. Transalloys was commissioned in the mid- 1960s as a high- and low-carbon ferrochromium plant based on the Perrin process. In 1967 the plant was converted to SiMn production because of constraints in the ferrochrome market (Basson, Curr, and Gericke, 2007; Bezemer, 1995). Today, the installed production capacity is 180 000 t of SiMn annually. Plant operations consists of five SAFs (see ratings in Table I), operating 24 hours a day, 365 days a year (including maintenance), involving 280 permanent employees, with up to 120 contract employees on site at any given time."

Jun 1, 2019

By L. Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pinpoint the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable temperature readings and gas analyses could have verified satisfactory activity. Hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: good record keeping is a necessity for collection of representative catalyst samples; reliable operating data is an inevitable starting point for all analysis; and trending of operating data is a must for plant optimization and troubleshooting. In addition, these catalyst management tools will give continuous updated knowledge of the catalyst status in each bed, providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking operating data, temperature optimization and good record keeping.

Jan 1, 2009

By R. P. Singh

A mine fire model gallery has been designed and constructed on the premises of the Central Mining Research Institute, Dhanbad, India to perform systematic in-depth studies on various aspects of mine fires. The gallery is 65.5 m long and 5.86 m2in cross-section and it is divided into firing and non-firing zones. It is equipped with a computer-aided online telemonitoring system that has 130 sensors, two data loggers and computer peripherals for continuous recording of various fire parameters. A fan to generate airflow through the gallery has been installed at its end. Two sliding doors and one rolling shutter were also provided for sealing and regulation of airflow. Two sets of experiments have been carried out in the model gallery maintaining air velocity of 1 and 1.5 m/s through it. In the experiments, the inner sides of the firing zone, 22 m in length, were lined with a thin layer (8?10 cm thick) of coal slabs. Two fire suppression techniques viz. flushing of liquid nitrogen (LN2) and infusion of high pressure high stability (HPHS) nitrogen foam were tried to quantify their effectiveness under dynamic fire conditions. The paper addresses important design features of the gallery, its instrumentation system, the experimental procedure adopted and important findings from the experiments. It has been observed that the intensity of the fire was very high after one hour of its initiation and continued for 3?4 hours. During the period, frequent backlash with smoke and flame was noticed. The efficacy of the fire suppression techniques has been assessed interms of reduction in temperature, generation rate of CO2and CO, and heat release rate. The study reveals that high pressure high stability (HPHS) nitrogen foam is more effective in controlling open fires than liquid nitrogen is. Keywords: Model gallery, telemonitoring system, velocity, temperature, pressure, gas concentration, intensity, liquid nitrogen, high pressure high stability nitrogen foam.

Jan 1, 2004

By A. Patri, D. S. Nimaje

Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before implementation of any wireless system, the variable path loss indices for different workplaces should be determined. This helps in better signal reception and sensor node localization, and also improves the method by which miners carrying the wireless devices are tracked. This paper proposes a novel method for determining the parameters of a suitable radio propagation model, which is illustrated with the results of a practical experiment carried out in an underground coal mine in southern India. The path loss indices, along with other essential parameters for accurate localization, have been determined using the XBee modules and ZigBee protocol at 2.4 GHz frequency.

Jan 1, 2015

By A. M. Hefny, F. P. Siew, P. G. Ranjith

Fracture initiation and propagation, being one of the most intensive subjects in rock mechanics; contribute significantly to the deformation of jointed rock masses. An experimental study on fractured granitic rock was carried out to determine the peak strength of specimen under triaxial loading conditions. The commonly observed failure mode for rock specimens in this study was found to be the shearing of the plane of weakness. The minimum peak strength of fractured rock is observed when the joint orientation is approximately 70° to the horizontal axis. Based on experimental test data, an empirical expression was developed to accommodate the effect of joint orientation and joint trace length in estimating the peak strength of fractured rocks. The predicted values of peak strength using the proposed equation well agree with the experimental results carried out on singly fractured specimens under triaxial loading conditions. The threshold stress values of crack initiation and propagation depend on joint geometrical parameters, their degree of interconnectivity, as well as surrounding stresses on the fracture plane.

Jan 1, 2003

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

By M. Abdellatif

The production of a 40% Al-Ti alloy was successfully proven at the lab scale, using pure TiO2, aluminium, and lime. These tests were conducted in an induction furnace maintained at 1600?16250C. The introduction of rutile into the feed recipe resulted in an alloy containing between 0.35 and 1.10% Zr, depending on rutile to TiO2 ratio. DC arc production of the alloy was largely accomplished at 40 and then 200kW scale. These tests evaluated various metallurgical and operational factors including target slag composition, Ti-content in the alloy, co-feeding versus sequential, furnace bath depth, and rutile as part of the Ti containing feedstock. Overall, an alloy containing 24?33% Ti was consistently produced with co-feeding of the reactants and with lower taphole tapping. When rutile was added, the zirconium analysis in the alloy remained below 0.2%. The main impurity elements were iron, silicon, carbon, nitrogen, and oxygen.

Jan 1, 2009

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012