Search Documents

By D. G. Krige

Some basic considerations in the application of geostatistics to the valuation of ore in South African gold mines by D. G. KRIGE, Pr. Eng., D.Se. (Eng.) Rand (Fellow) There is much room for improvement in the statistical procedures that have been used by gold mines over the past decade in the valuation of their ore reserves. Improvement depends on the establishment of the extent to which the patterns of frequency distributions and the directional variograms for the gold values vary from area to area within each section of a mine. The application of the lognormal distribution and of the De Wijsian variogram model for routine ore-reserve valuations requires detailed study before some of the reservations still held by mathematical statisticians can be met. This paper provides some preliminary evidence of the extent to which these models can be used with confidence, as well as suggesting how they can be applied to their full potential.

Jan 4, 1976

By J. J. Geldenhuys

Premier of the North-West Province, Mr Molefe, foreign dignitaries and guests, ladies and gentlemen. It is a pleasure and also a special honour for me to have been invited here this morning to make this address. The xv Congress of the Council of Mining and Metallurgical Institutions is, by its very nature, an extremely important event for the international minerals industry. But I believe that this specific Congress assumes an even greater significance because of the profound and far-reaching changes that have taken place in South Africa this year. These are exhilarating times, a period when so much in our country has altered and when so much has to be done so quickly to build positively on our bold political decisions.

Jan 1, 1994

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, J. M. A. Geldenhuis

The successful application of solid electrolytes in electrochemical cells for high-temperature thermodynamic studies depends to a large extent on an accurate knowledge of the P. value of the electrolyte (the oxygen partial pressure at which the ionic conductivity and n-type electronic conductivity of the electrolyte are equal). Consequently, the P. value of an electrolyte must be determined prior to its use in electrochemical cells. This paper describes the successful application of a coulometric titration technique in the quantitative assessment of the P. values of a commercially available ytria-stabilized zirconia electrolyte that has been used extensively by local investigators. The experimentally determined P. values of the electrolyte are reported and compared with P. values reported in the literature for a similar electrolyte.

Jan 1, 1988

By B. H. Sandelowsky

Prehistoric metal-working in South West Africa by B. H. SANDELOWSKY*, Ph.D. (Visitor) This paper describes a three-hundred year old metal-working site at Rehoboth, and makes a plea for information on such sites elsewhere in South West Africa so that they can be investigated. The technique of ore smelting that was used at Rehoboth appears to be different from that practised elsewhere by Bantu peoples before the modern era.

Jan 5, 1974

British Mining Fields, by J. E. Metcalf. Published by the Institution of Mining and Metallurgy, London, 1969. Price 50s. (Students, 30s.). A 100 years or so ago Britain's mining industry led the world in the production of coal and base metals. Although she still maintains a sizeable-and, under the circumstances, remarkably progressive-coal mining industry, her production of most other base minerals has long since been dwarfed by mining fields in the Americas Africa, Australia and the U.S.S.R. Nevertheless the story of mining in Britain is of wider interest than the present scale of operations there might suggest, if only because the domestic British mining industry has in terms of finance, technology and manpower been the fons et origo of many highly productive mining fields outside Britain, including the Witwatersrand goldfields. British Mining Fields was published by the Institute of Mining and Metallurgy to give delegates attending the Ninth Commonwealth Mining and Metallurgical Conference a succinct account of mining in Britain. The main emphasis is on underground mining of base minerals-treated regionally-with separate chapters on coal and gypsum. The author strikes an admirable balance between historical aspects, geological origin and environment of ore deposits, mining methods and economic factors, and provides a few key references for those who wish to make deeper studies. This is exactly the sort of booklet one often wishes were available on South African mining.

By H. A. D. Kirsten

The paper reports on loading tests conducted on shotcrete reinforced with mesh and various types of steel fibre, and compares the results with the energy absorbing capabilities of 16 mm rebar shepherd's crooks. It is concluded that mesh-reit1forced shotcrete has sufficient energy-absorbing capabilities to contain rockbursts of significant magnitude, having greater energy absorbing capabilities, even at a thickness of 50 mm, than 16 mm rebar shepherd's crooks. Fibre-reinforced shotcrete has energy absorbing capabilities of the same order as, or better than, those of 16 mm rebar shepherd's crooks, but its performance is erratic.

Jan 1, 1995

By S. W. Evans, G. Pienaar

Weldable steel plate with a good combination of strength and toughness is currently produced from 0,12 to 0,28 per cent carbon low-alloy steel heat-treated by roller quenching and tempering. Alternatively, steel plate of the same strength can be produced at a lower production cost by the use of very-low-carbon steel (0,03 to 0,08 per cent carbon) processed by in-line quenching without tempering. This paper reports the results of experimental work on these steels, and compares them with the properties of conventional steel. On thinner sections, it was found that the properties of the experimental steels compare favourably with those of conventional grades.

Jan 1, 1989

By M. P. Mohring

A School on the Total Utilization of Coal Resources, which was organized by the Technical Programme Commitee of The South African Institute of Mining and Metallurgy in conjunction with the South African Coal Processing Society, was held in the Civic Theatre at Witbank from 30th October to 2nd November, 1989.

Jan 1, 1990

The 90th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 19th August, 1987. Dr H. Wagner (President) was in the Chair and declared the meeting open at 16h00. Obituaries The President read out the names of the departed Members as follows: N.M. Airey, F.J. Kisbey-Green, Dr R.A. Pelletier, C.B. Anderson, A.R. Cator, J. van Heerden, P.J. Burman, C.C. Crosson, M. Livingstone¬Blevins, S.T. Firman, V.E. Kisbey-Green, and A.L. Corna. All stood and observed a moment of silence as a mark of respect. Minutes The minutes of the 89th Meeting of the SAIMM, which was held on 20th of August, 1986, were confirmed.

Jan 1, 1987

Sedimentary Ores-Ancient and Modern (Revised), edited by C. H. James. Proceedings of the 15th Inter-University Geological Congress. University of Leicester, December, 1967. Special Publication No.1, Department of Geology, University of Leicester, February, 1969. Obtainable from: Leicester University Bookshop, May's Walk, Leicester LE 17 RD. Price: 42s. Postage and packing, 3s. 6d. This volume should be of interest to economic geologists and students in this field. A number of illustrated papers on the genesis of ores in sediments are presented; the authors include experts such as Prof G. C. Amstutz, Dr K. C. Dunham, Prof D. Williams and W. G. GarIick. The papers deal mainly with sulphide deposits, but the late Prof J. H. Taylor's contribution concerns ores of iron and manganese. Brief references to the Witwatersrand ores represent the only discussion of South African deposits. With the notable exception of W. G. Garlick's paper on Zambian copper deposits, the Abstracts given are inadequate, necessitating thorough reading of the papers to extract the important matter.

By G. R. Marchant, B. K. Loveday

A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation. Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression. The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficial.

By L. A. Cornish, B. Eatwell

Austempered ductile iron (ADI) is a ductile iron which has had its matrix toughened by an austempering process. The alloy exhibits remarkable properties, which it owes to a unique microstructure comprising graphite nodules embedded in a matrix of acicular ferrite and carbon-enriched austenite. The properties include high strength combined with high toughness and ductility. Excellent wear resistance is also exhibited because, under strain, the austenite is transformed locally to martensite. Samples of ductile iron were austempered to produce grades I and IV AD!, and were tested at various strain rates. The grade IV ADI exhibited higher strengths and lower difficulties, and the strengths were found to be more dependent on strain rate. Transformation to martensite was more prevalent at the lower strain rates. A mechanism of increased flow stress and work hardening in the austenite of the matrix is proposed to explain the higher strength of the samples at high strain rates, where significantly less martensite is formed in the matrix.

Jan 1, 1995

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By Y. P. Shoupletsov

ABSTRACT. A retrospective analysis of some geomechanical classifications for rock masses is presented. It is shown that estimates of rock mass strength according to geomechanical classifications developed, e.g., for construction of tunnels and for ore mines can differ very much. Development of specifically oriented classifications for rock masses with certain geomechanical properties is required. ZUSAMMENFASSUNG. Es wurde eine retrospektive Analyse einiger geomechanoschen Klassifikationen von Gesteinsmassiven durchgefuhrt. Es idt aufgezeigt worden, dass die Bes-timmung der Festigkeit des Massivs nach geomechanischen Klassifikationen, die z.B. fur den Bau von Tunnelen und fur Erzbergwerke entwickelt wurden, sich um etliche Male unterscheiden kann. Es ist eine Entwicklung von spezialisierten Klassifikationen fur Gesteinsmassive mit bestimmten geomechanischen Eigenschaften erforderlich. RESUME. Il a ete fait l’analyse retrospective de certaines classifications geomecaniques des massifs de roche. Il a ete montre que les estimations de solidite du massif suivant les classifications geomecaniques etudiees, par exemple, pour la construction des tunnels et pour les puits de minerai peuvent differer en quelques fois. Il est donc necessaire d’etudier les classifications specialisees pour les massifs aux proprietes geomecaniques particulieres.

Jan 1, 2003

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

By A. Morley

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

By P. J. D. Lloyd

The Witwatersrand reefs contain gold, uranium, and pyrite in the following average concentrations: 0,001 per cent, 0,02 per cent, and 1,7 per cent respectively. The paper discusses the flotation of pyrite to produce a s,ulphide concentrate, reviews work done on the production of gold concentrates, discusses attempts to produce maximum concentrates, and closes with a review of processes for the simultaneous flotation of these three species. It is concluded that high recoveries of all three species can be achieved only if a rougher concentrate of perhaps 20 per cent of the feed (by mass) IS produced, and it is suggested that reverse leaching (leaching before cyanidation) of this concentrate, followed by a cleaning flotation step for the recovery of the pyrite, would be more efficient than the routes employed at present.

Jan 1, 1981

By A. Whillier

Recommendations are given for the design of vertical cooling towers for use underground in mines and a method is given for predicting the entering and leaving water temperatures when a given amount of heat has to be dissipated.

One of the main bottlenecks in the carbon-in pulp process for the recovery qf gold is the elution procedure, which typically requires the heading of caustic cyanide eluants to high temperatures for 16 to 24 hours. The present work demonstrates that sodium sulphide solution as an alternative eluant can effect complete elution in about 4 hours at ambient temperatures. Elution efficiencies of around 100 per cent were obtained in 4 hours with a single pass of eluant containing 0,2 M Na2S and 0,4 NaOH about 10 bed-volumes of eluant The initial rate was slow over the first hour of elution, probably because the activated carbon catalysed the oxidation of sulphide to polysulphide. Elution efficiencies of around 100 per cent were also obtained in less than 4 hours during the batch elution of carbon at liquid-to-solid ratio of about 100. Lower liquid to solid ratio resulted in the re-adsorption of gold, probably owing to the oxidation of sulphide to polysulphide, with the resultant formation of gold complexes that were eluted less readily. Improved rates of elution were obtained at higher sulphide concentrations and pH values greater than about 13. Higher temperatures increased the initial elution rate, but lowered the overall extraction efficiency, probably because of the deposition of elemental gold on the carbon. Variation of the ionic strength by the addition of NaCl had no defect on the elution, which confirms that the elution mechanism in the case of sulphide is different from that when cyanide or I1)1droxide is used as the eluant. It is proposed that the elution of gold by sulphide solutions proceeds by means of an initial step that involves the reaction of polysulphide ions with the adsorbed aurocyanide speeds, forming AuCN on the carbon and thiocyanate in solution. This step is followed by the formation of poorly adsorbed complexes with sulphide ions, such as [AUS3-2]-The presence of polysulphides, whether generated in situ by the catalytic oxidation effect of activated carbon or by the addition of elemental sulphur, reduces the elution rate and efficiency dramatically. This is probably due to the formation of complexes such as AUS-3 and AUS-2 , which have a high adsorption affinity.

Jan 1, 1994

By H. E. Cross

The conversion of a uranium plant to the recovery of zinc by H. E. CROSS. B.Sc. (Eng.)(Hons.) Rand (Fellow) The conversion of the Vogelstruisbult Uranium Plant into a plant for the production of electrolytic zinc is described. The reasons for the conversion, the preliminary investigations. and the basic design principles are all outlined, and a brief account is given of operating experience.. during the commissioning of the plant, with equipment that had been put to a use for which it was not originally Intended.

Jan 11, 1973