Search Documents

By V. E. Ross

A computer program was developed that incorporates a novel analysis of the behaviour of the froth in full-scale cells to predict the performance of the froth over a wide range of operating conditions. The program has the distinct advantage that it can be easily implemented on a microcomputer, which allows rapid computation and processing of the results. The program utilizes experimental data obtained in flotation-plant and laboratory testwork to provide parameters for the froth model under an initial set of operating conditions. These parameters can then be used in conjunction with a model describing the transfer of material from the pulp to the froth to predict the performance of the cell when its dimensions and operating variables are changed during scale-up.

Jan 1, 1987

By K. Forsberg, Ş. Kaya, C. Dittrich, M. Svärd, E. M. Peters

Scandium can be recovered from waste streams of other metallurgical processes such as red mud from the Bayer process and titanium dioxide acid waste. This is accomplished by an integrated process comprising leaching using acidic media, solvent extraction using organic solvents and stripping of Sc from the organic phase using NH4F solutions. The precipitation of scandium as (NH4)3ScF6 from NH4F strip liquors has been demonstrated at lab-scale with recoveries and purities greater than 98% and 98.3%, respectively. It is desired to assess the possibility of recovering the solvents for re-use in the process to improve its economy and environmental friendliness. Investigations have been conducted to recover alcohol by simple distillation from strip liquor-alcohol mixtures containing about 50 v/v% alcohol. The mixtures were obtained after anti-solvent precipitation of (NH4)3ScF6 using an alcohol to strip liquor volumetric ratio of 1:1. The starting strip liquor contained about 2000 mg/L scandium in 3 mol/L NH4F solution. In the recovery of methanol, the first distillate product collected had a purity of about 87 v/v% and this decreased slightly with time over two hours. The methanol distillate collected in the first 30 minutes with a purity of ca. 85 v/v% was re-used in anti-solvent crystallisation of (NH4)3ScF6 from the initial strip liquor, and the scandium recovery attained was about 98.6 w/w%, almost similar to that of 99.2 w/w% obtained using 100 v/v% methanol. For ethanol recovery, the first distillate product collected was approx. 84 v/v% pure and the distillate collected in the first 30 minutes with a purity of about 75 v/v% achieved a scandium recovery of about 97.2 w/w% in comparison to 98.5 w/w% obtained using 100 v/v% ethanol during anti-solvent crystallisation. Keywords: Alcohol recovery, methanol, ethanol, anti-solvent crystallisation, (NH4)3ScF6

Jan 1, 2020

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By El-Sayed M. Sherif, J. D. Comins, Erasmus R. M.

Corrosion of copper in aerated acidic chloride pickling (0.5 M HCl) solutions and its inhibition by 3-amino-1,2,4-triazole-5-thiol (ATT) have been investigated using electrochemical techniques and weight-loss measurements, along with Raman spectroscopy. Electrochemical measurements for copper after varied immersion periods of 0, 24 and 48h showed that the presence of ATT and the increase of its concentration significantly decrease cathodic, anodic, corrosion (jCorr) currents and corrosion rates (KCorr), as well as the dissolution currents at 300 mV vs. Ag/AgCl, while increase polarization resistance (Rp), degree of surface coverage (?) and inhibition efficiency (IE%) to a great extent. Weight-loss measurements after different immersion periods of 6 ~ 48h revealed that the dissolution of copper decreased to a minimum and the corresponding IE% increased with ATT concentration increases. The detection of ATT molecules on the copper surface by Raman spectroscopy indicated that inhibition of copper corrosion is achieved by strong adsorption of ATT molecules onto the copper surface. Aerated acidic pickling solutions; 3-Amino-1,2,4-triazole-5-thiol; Copper corrosion; Corrosion inhibition; Raman spectroscopy

Jan 1, 2006

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By K. F. Lane

Mine planning is a complex function and also a vital one. The quality of the planning has a profound effect on the efficiency and the economics of every mining operation. It is therefore important that the function should not be reliant upon only a few techniques but should have command of an orchestra of them. Then the most appropriate can be selected for each application or, if it is advantageous, a group can be employed in concert. This paper introduces peripheral algebra as a set of techniques which should be included in the mine planning orchestra. Its objective is primarily to stimulate more development not only of these techniques but also others of a similar kind which will increase the effectiveness of mine planning.

Jan 1, 1987

By More-O&apos, R. C. Ferrall, J. W. Wilson

SYNOPSIS The theory of elasticity has been shown to provide a means of determining the stresses and displacements induced by mining in deep level hard rock mines. This theory has been incorporated into an electrical resistance analogue on which the plane of a reef or ore-body can be modelled to enable the rapid determination of stresses and displacements at points in the plane of the reef. This electrical analogue has been used to determine energy release rates caused by scattered mining, which, to some extent, is a measure of the degree of hangingwall fracture. A correlation between predicted energy release rates and actual underground conditions in stopes in the O.F.S. goldfields has been encouraging enough to define parameters on which future stoping layouts can be based. The use of the elastic theory through the analogue has been extended to the assessment of the influence of stoping operations on off-reef excavations. Underground conditions at damaged and undamaged areas have been compared with predicted elastic stresses at the positions under review, resulting in the derivation of design parameters for use in siting off-reef excavations in the prevailing geological conditions in the O.F.S. and Klerksdorp goldfields. The analogue has also been used to assess the vulnerability of certain un mined dykes to bursting. Correlations between stresses induced on dykes by stoping and dyke behaviour underground has enabled critical stress levels to be determined for several persistent dykes occurring in the O.F.S. and Klerksdorp goldfields. A number of long and short term planning projects at mines operating in the Anglo American Corporation and General Mining and Finance Groups are described, where the data derived from the electrical resistance analogue is processed by computer programmes and assessed on the strength of the design factors derived from the correlation of field work and the elastic theory.

Jan 1, 1970

By J. W. Oberholzer

The use of computers in the South African coal mining industry has increased during the 1980s. Applications at mine level commenced in the financial and personnel areas of payroll systems, mine accounting procedures and staff record keeping. More use is made now on mines of technical programs for purposes such as mine planning and mine survey calculations. The Coal Mining Laboratory of the Chamber of Mines Research Organization has provided, for a number of years, a service to Chamber member collieries in regard to the application of technical computer programs. Programs presently in use for simulating production procedures and conveyor belt transport systems are described. In addition, reference is made to the collection, storage and analysis of data concerning the performance of continuous miners over a period of eight years. More recently a computer program for the simulation of the cutting action of continuous miner cutting drums has been developed. The use of this program to assist with drum design is explained. The fact that many requests to make use of the programs are received from collieries is an indication of their acceptance by industry. Their interest in running the programs themselves on their own desktop computers has led to the need to convert the software for microcomputers.

Jan 1, 1987

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 23rd August, 1978. Mr P. A. von Wielligh (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : T. K. Prentice and W. E. Gooday, Honorary Life Fellows and Past Presidents; B. S. Allen, J. A. Becking, L. H. Mellor, C. A. Pratt and W. T. Stobart, Life Fellows; J. P. Burls, E. Cameron, M. L. Fitzgerald, C. G. Hinds, A. J. Patrick, H. O. Reisener, N. D. Shuttleworth, N. Soldan and J. Whitehouse, Fellows; T. Gemmell, J. S. A. Oelofse, W. D. Rowe, R. L. J. Shearman and G. M. Thain, Associates. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. Welcome The President: It is now my very pleasant duty to welcome our distinguished guests and visitors. We are pleased to have with us Mr D. A. Etheredge, Vice¬President of the Chamber of Mines of South Africa, and Mrs Etheredge. Mr Etheredge this afternoon represents the mining industry at our meeting. The importance of the close link that over the years has been maintained between the industry and our Institute speaks for itself. We are, therefore, grateful that he and Mrs Etheredge have managed to find the time to be with us this after¬noon.

Jan 1, 1979

By J. J. Cilliers, I. K. Craig, J. D. le Roux, K. Hadler

An analysis of the state-observability characteristics of a dynamic tank-to-tank model of a flotation bank indicates that the concentrate-flow rate of each tank can be estimated from accurate measurements of the pulp height in each tank and the final tailings flow-rate exiting the final tank. Therefore, there is an opportunity to construct an observer (model-based soft-sensor) which can estimate the concentrate flow-rate of tanks in a flotation bank. The concentrate flow-rate, i.e. mass pull, is generally measured by means of froth image analysers on industrial plants. A model-based soft-sensor will not only provide a means to validate froth image analyser results, but could potentially substitute them as they are less expensive to implement and maintain. Keywords: Concentrate flow-rate, estimation, flotation, modelling, observability, soft-sensor

Jan 1, 2020

By N. J. Alderman, D. J. Clowes, N. I. Heywood

The effects were studied of the presence of comminuted flint on the rheological characteristics of chalk slurry pumped through a 92-km long pipeline from Kensworth Quarry to Rugby Cement Works in the UK, and their impact on the pipe flow conditions. Flow curves were measured for 63different chalk slurry samples; these were described by the Bingham plastic model. In addition to observing trends in the yield stress parameter and plastic viscosity in the model with variations in both flint concentration and dispersant additive, use was also made of slurry viscosity values at a reference shear rate of 60 s-1for the pipe flow. It was found that chalk slurry viscosity decreases with increasing flint content up to 10% by weight for a given additive concentration, and increases with increasing additive concentration from 0.7 to 1.0%, for a given flint content. The pipeline flow regimes were identified using the critical value of the Bingham Reynolds number for laminar flow breakdown. For Bench 11 (quarry bottom) chalk slurries, it was observed that all sections of the pipeline operate in the turbulent flow regime for the nine different formulations and for the three pipe diameters used along the pipeline. However, this was not always the case for Bench 1(quarry top) slurries. It was therefore recommended that chalk slurries prepared from Bench 1 should not be used because of the strong likelihood that laminar flow conditions will occur owing to the presence of higher clay concentrations within this bench. This, in turn, will lead to an unsafe operation of the pipeline because of the potential for coarse particle settling. Likewise, blending of chalk from Bench 1 with the lower benches such as Bench 11 could be problematic and this requires further experimentation.

Jan 1, 2007

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By A. J. Reynolds

In recent years, rapid depletion of the higher grade reserves, allied to decreases in paylimits, has led to the exploitation of secondary, erratically mineralized placer horizons on various marginal and low grade gold mines. On Blyvooruitzicht Mine, the rich Carbon Leader Reef has limited reserves, necessitating exploration of the lower grade Middelvlei Reef. This placer has always presented evaluation and exploration problems, to such an extent that it was, at one stage, considered uneconomic. Despite an extensive underground drilling programme no ore reserve targets of reasonable size were apparent. However, when a certain degree of parallelism between sedimentological trends in the Middelvlei Reef and the underlying Carbon Leader was recognized, a meaningful exploration model could be developed. Firstly, all historical sampling records for the Carbon Leader were entered into a computerized system; the database comprised in excess of 340 000 data points. Variables captured consisted of gold value, uranium value, con- glomerate thickness and total reef thickness. The raw data were then averaged into blocks, and plots of different variables were computer-generated for further analysis. This enabled the Carbon Leader to be modelled sedimentologically and, thereby, exploration targets for the Middelvlei Reef were generated, based on the Carbon Leader facies trends. Geostatistical analysis of sampling data in exposed areas of the Middelvlei Reef underground has confirmed the sedimentological breakdown of the placer into distinct facies areas. A facies model relating value distribution patterns to depositional trends, both for the Carbon Leader and the Middelvlei Reef, has thus been incorporated into a mine planning strategy.

Jan 1, 1987

By M. Pötsch, W. Schubert, A. Goricki

Geological and geotechnical data are essential for the design of tunnels. To determine the rock mass behavior and the support of a planned tunnel excavation a consistent method for rock mass characterization and excavation and support determination has been developed. Probabilistic data processing with analytical methods is used for the quantification of the procedure and allows an evaluation of the applicability and the technical risk of different excavation and support methods. The sensitivity of the procedure on selected input parameters is highlighted in a parametric study. Finally an application of the procedure illustrates the use of the described method of probabilistic excavation and support determination for tunnels. Des données géologiques et géotechniques sont décisives pour la planification d’un tunnel. Pour la détermination du comportement des strates, le choix du soutènement et de la méthode de progression une description compréhensible de la montagne a été développée. À l'aide d'un traitement de données probabiliste, la procédure proposée est transposée quantitative sur une base de méthodes analytiques. De cette manière l'évaluation des méthodes de construction et la détermination du risque technique deviennent possibles. La sensitivité de la procédure de différents paramètres d'entrée est représentée dans une étude de paramètre. Pour finir, l'application de la procédure décrite est montrée à l’aide d'un cas pratique. Geologische und geotechnische Daten sind entscheidend für die Planung von Tunnels. Für die Ermittlung des Gebirgsverhaltens und der Festlegung von Ausbruch und Stützung wurde ein nachvollziehbarer Ablauf der Gebirgsbeschreibung entwickelt. Mit Hilfe von probabilistischer Datenverarbeitung auf Grundlage analytischer Methoden wird die vorgeschlagene Prozedur quantiativ umgesetzt. Dadurch werden die Bewertung von Baumethoden und die Ermittlung des technischen Risikos ermöglicht. Die Sensitivität des Verfahrens von einzelnen Eingangsparametern wird in einer Parameterstudie dargestellt. Abschließend wird anhand eines Beispiels die Anwendung des beschriebenen Verfahrens gezeigt.

Jan 1, 2003

By M. Splaine, C. E. Dohm, S. J. Browner

As the grade of the gold (head grade) in the ore supplied to a reduction plants falls, the efficiency of recovery of the metal drops. This is not simply due to a fixed grade lost in the residue, since the residue grade is itself a function of the head grade. A multi-disciplinary approach was used in the construction of a model to represent the relationship between head grade and recovery efficiency. The model is a physicochemical one based on (i) the reaction characteristics of cyanidation, (ii) the milled-ore selection characteristics of gravity concentration, and (iii) the nearly log normal distribution of gold grades and particle sizes in ore reserves. The model was used to set sound target levels for recovery efficiency for a given head grade at a given plant, against which the performances of the plant equipment can be judged for control purposes.

Jan 1, 1982

Brigadier R. S. G. Stokes of Sherborne, Dorset, is the oldest surviving member of the South African Institute of Mining and Metallurgy. He joined in 1904 and has been a member for 77 years. Book review Sittig, M. Hand book of catalyst manufacture. Park Ridge (U.S.A.), Noyes Data Corporation, 1978. The detailed information in this book is based on patents issued in the U.S.A. that deal with catalysts and their commercial technology. Project management The South African Institute of Mining and Metallurgy is to hold a Colloquium on Project Management in the Metallurgical Industry in March 1980. Ingenieurs-in-opleiding in die weermag Op 'n onlangse vergadering van die Suid-Afrikaanse Raad vir Professionele Ingenieurs is daar besluit om kwytskelding van jaargeld aan geregistreerde ingenieursin- opleiding wat tans met hulle tweejaar nasionale diensplig besig is, te verleen met dien verstande dat.... Engineers-in-training in the army At a recent meeting of the South African Council for Professional Engineers it was resolved that a remission of annual fees would be granted to registered engineers in- training who are doing compulsory two-year national service, provided that.... Processing of fine particles The Society of Mining Engineers of AIME is organizing an International Symposium on Fine Particles Processing, which is to be held in Las Vegas from 24th to 28th February, 1980. Economics of precious metals International Precious Metals Institute announces a Special Course for all interested in economic aspects of today's precious metals.

Jan 1, 1979

By H. M. Krieg, M. J. Ungerer, C. G. C. E. van Sittert, D. J. van der Westhuizen

"The transition metals tantalum (Ta) and niobium (Nb) are of significant importance, for example in the nuclear energy sector where they are used as cladding materials, as well as in capacitors and specialized materials. For these applications a high-purity metal is needed. The separation of Ta and Nb is always a challenge since they are found together in nature and have similar chemical and physical properties, resulting in costly and laborious separation processes. A technology that has been used successfully for the separation of these metals entails solvent extraction (SX)1. While separation was achieved in a previous SX study using a sulphuric acid (H2SO4) medium with the extractants diiso-octyl phosphinic acid (PA) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), due to the absence of speciation data for Ta and Nb it is not clear how the separation occurred.One method that might be suitable for determining the speciation of a reaction is molecular modelling. Calculations based on the densityfunctional theory (DFT) are now used not only for light elements and small molecules, but also metal complexes, heavy metals, and especially metal separation in SX2. In this study the aqueous phase used during SX was investigated by studying periodic systems of Ta, as a metal and in salt form, when it is in contact with H2O and H2SO4. The results were used to predict the reaction mechanism occurring during SX. Results showed that (i) in a 1:1 acid-water ratio, the deprotonation of H2SO4 was endothermic, (ii) in a 1:5 ratio deprotonation was exothermic forming HSO4 -, and (iii) in a 1:10 ratio double deprotonation occurred to form SO42- exothermically."

Jan 1, 2017

In many practical situations, the samples available to estimate a block of ore are not located on a regular grid. The sample sizes and orientations are not constant, and the number and relative position of the samples used for valuation of each block change from block to block. Estimation of a block W might be very complex and time consuming if each sample in the neighbourhood of the block were considered individually. A practical solution consists of grouping the samples in blocks Wi (i = 1, 2, . . . n) in the neighbourhood of W, and estimating µw as a weighted average of the mean xi of the samples in Wi. Possible ways of grouping the samples are illustrated in Fig. 1 1.1. More complex patterns can be found in the literature (Krige, 1966) To calculate the kriging estimator of pw, we must be able to calculate the variance of xi, the covariance of xi and xj, and the covariance of xi and pµw. The purpose of this chapter is to show how these quantities can be calculated when we ignore the position of the samples in the block Wi. We consider the samples to be randomly distributed in Wi; kriging with this assumption is known as random kriging.

Jan 1, 1978

By I. E. Teymenson, N Fedunets

Mining-metallurgical complex is the base of any economics and influences directly on practically all branches of world economics. Therefore the task of estimation and selection of investment decisions in mining industry adequate to modern market conditions and the task of decreasing multidimensional alternatives selection uncertainty are very actual. An uncertainty of investment alternatives is explained by a number of reasons, main of which are a presence of several investors types, an unstable situation on the market and an absence of evident relations between appraisal criteria used. Maximum increasing of formalization and objectivity of information technologies applied for an estimation permits to reduce the uncertainty of investment variants estimation. A number of principled innovations, allowing to solve the task of decreasing of multidimensional alternatives selection uncertainty, are introduced into the information technology of estimating and selecting investment decisions in mining-metallurgical branch, developed by us. In the article the necessity of including a cognitive model into developed selection mechanism, which allows to take into consideration inter-influences of used critera, has been grounded. Besides, the forecasting model considering interconnected time rows has been applied for increasing the world conjuncture forecast quality. Further in the article main metrics types have been characterized and application of weighted Chebyshev’s metrics as the most compromised from all studied metrics for variants selecting has been proved, and also the developed procedure of directional search of effective compromise decisions has been described. Brief characteristic of designed instrumental means of multi-criteria variants estimation and selection finalizes the article. In conclusion expedience and efficiency of using the developed information technology for reduction of multidimensional alternatives selection uncertainty have been grounded.

Jan 1, 2003