Search Documents

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for O2, N2, H2, He, and Co2. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4/CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By F. L. Wideman

Materials handled at metal and non-metal mines in the United States increased 10 percent compared with those of 1965 as a result of expansions in output at existing mines and development of others to meet increasing demands for mineral products. The tonnage of commercial materials mined or quarried increased as did the quantity of waste handled. Crude material from which metal or nonmetal products were derived comprised 71 percent (75 percent in 1964) of the total materials handled. Great strides were made in mining technology and there were indications that, in the future, earth moving by the mining industry will involve materials-handling systems of increasing size and complexity. Materials Handled.-Output of ore and waste at metal and nonmetal mines and quarries in the United States in 1966 totaled 3,518 million tons (3.213 million tons in 1965). The quantity of materials handled has increased at an average annual rate of 5 percent since 1962. Ore production increased 4 percent over that of 1965, also comparable to the average annual rate of increase in the last 5 years. Waste removal in 1966 increased 25 percent over that of the previous year.

Jan 1, 1967

"Reports are sometimes heard of one ill effects of pneumatic tools on the hands of workmen. In consequence of such reports, Dr. Francis M. Barnes, Jr., M..D. of St. Louis, Missouri, was retained by the operators to make an investigation of conditions in the Bedford, Indiana, region, and the result of this investigation was published the Journal of the Missouri State Medical Association, Volume 16, February 1919. A brief review of this report may be of interest to all users of pneumatic tools, or operators of plants where such tools are employed.The investigation was made during December 1917, and involved an examination of general working conditions, and a careful physical examination of stoneworkers who had long used pneumatic tools. As the Bedford district is the most important structural limestone producing center in the country, the results of this investigation may be regarded as fairly conclusive as to the general effect of pneumatic tools on limestone workers."

Jan 1, 1920

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The usual run time errors occur when illegal mathematical operations are attempted by MFIRE For exam¬ple, if the user enters a negative value for the input variable HEAT to model a heat sink or cooling station, a run tame error will occur because an exponential function is employed to better model the changing temperature dis¬tribution in the airways. DATA FILE ERRORS Two types of data file errors can occur. 1 An error may occur because the input data file itself is invalid This may be caused by: The data file cannot be found due to incorrect spelling, drive, or path specification Check the spelling and path at the prompt for location of the data file. The data file contains non-ASCII symbols Check op¬eration of the text processor to insure that only ASCII characters are produced Delete all non-ASCII and/or all out of place characters. 2 Data are accepted by the program, but are incorrect for the data types or ranges or the combination causes a data inconsistency This may be due to. An invalid character is located where a numerical value is required The input data value is outside the reasonable range The input data is insufficient to build the model for simulation. The input data exceeds the capacity of the program. PROGRAM ERROR DETECTION When the program is running, tracing messages are given on the screen indicating the group and lines of data that have been read and the section of the program that is executing Program termination indicates that problems are caused by the subsequent (not read) data file section. For each detected error, descriptive message starting with * ERROR * is issued and the program terminates. When a possibly wrong value and/or its calculated intermediate result is detected, a descriptive message starting with * WARNING * is issued and the program continues. If a modification of input value or calculated intermediate result is automatically made by the program, descrip¬tive message starting with * ATTENTION * is issued and the program continues. LOCATING ERRORS If a message indicates that the error condition occurred due to the data input file, locate and correct the data item. If no error message is issued, but the simulation results are not as expected, carefully check the list of input data shown in the output file WARNING messages and ATTENTION messages may reveal an error in the input data even though the program continues to operate Insure that the default values or modifications adopted by the program run are acceptable. Anomalistic data, though not incorrect or impossible, may lead to an unusual simulation For example, making a fan unusually powerful may prevent a normal strength fire from affecting the airflow distribution in the system Much care must be employed before considering an ex¬treme case. If a message indicates that the accuracy criterion in the temperature section of the program was not satisfied, a table detailing the current parameters of airways which have large fluctuation in the average air temperature from iteration to iteration is produced If the pattern of the parameters is clearly cyclical, while the variation of natural ventilation pressure is stable or cyclical from iteration to iteration, then, most likely there is no single equilibrium stage for the event If the variation of natural ventilation pressure decreases steadily though slowly, increasing the value of data item variables MADJ or ITN (on control line number 1) may allow convergence.

Jan 1, 1990

The following additional studies are recommended: 1. Future development of the magnetic sludge process should involve optimization of the process variables; these include stirring rate, sludge heating time, aeration rate, method of preliminary sludge dewatering, and the effects of magnetic separation for final sludge processing. In addition, the matter of amenability of coal mine waters to treatment should be considered more thoroughly by means of a more comprehensive literature review as well as actual tests on mine drainage samples. 2. The technique of sludge freezing should be explored further. Emphasis should be given to conservation of energy in the process, and the filtration characteristics of the resulting sludges should be evaluated. 3. Further studies should be conducted on the feasibility of the CO2-addition approach to mine drainage sludge densification. The filtration characteristics of product sludges should be evaluated, and the possibility of recovering and recycling the residual alkalinity of the sludge, either directly as CaCO3 or as CaO plus CO2 after calcination, should also be explored further. 4. Efforts should be made to develop cost data for the conceptual processes involving magnetic sludge formation, sludge freezing, and C02 pretreatment, with the purpose of selecting at least one of these processes for further testing at a field site. 5. The use of inexpensive waste materials (e.g. fly ash, "red dog," slag) as sludge additives, possibly in conjunction with coagulant aids, should be considered further. Results of the present studies have indicated that such materials, employed in relatively large amounts, increase the density and enhance the filterability of sludges from lime neutralization of coal mine drainage. The use of pulverized blast furnace slag in this regard appears particularly promising, and studies should be made to ascertain its availability, relative cost, residual alkalinity, and behavior as an additive in conventional mine drainage treatment processes involving lime neutralization and aeration.

Jan 1, 1971

By Launa Mallett

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.

Jan 1, 1999

By Launa Mallett, PhD, Charles Vaught, PhD

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.

By D. Harrington, B. W. Dyer

"One of the products of the activities of the United States Chemical Warfare Service is a simple device and method for nearly instantaneous determination of small quantities of carbon monoxide in air. Since the war, this device has been diverted to commercial uses, and is now being marketed in connection with rapid determination of the comparatively small but dangerous quantities of CO, which may be found in garages, in sewers, about blast furnaces, etc. Also, it probably has a definite field of use in both coal and metal mines in connection with fires and explosions, as well as in confined places after firing of explosives) the latter applica-tion being of especial importance in metal mining.The device as marketed is readily portable, being small and light enough to carry in a coat pocket of medium size. In operation, a sample of the air mixture is drawn into a small rubber bulb, then forced through a small glass tube filled with certain chemicals upon which CO has the effect of changing the original color from gray or white to shades of green, the deepness of the green determining the percentage of CO in the air. A color scale is attached for purpose of comparison and determination of CO percentage. Only a few minutes are consumed in obtaining the result, all work being done on the ground.The exact effect of minute quantities (up to 1/10 of 1 percent) of CO on the human system is somewhat uncertain, and much research has been and is being done to obtain definite data on this point. It is, however, definitely known that in air containing more than 1/10 of 1 percent CO men doing hard work are quickly and seriously affected. As the gas is tasteless, colorless and odorless, methods of determining the presence of both small and large quantities have been of much importance. Technical Paper 11 of the U. S. Bureau of Mines gives much data as to effect of CO on mice and canaries. It was found that mice show very little distress until the CO content is about 0.20 percent, but quickly succumb when that percentage is exceeded; canaries are somewhat more susceptible; they quickly show distress in as little as 0.15 percent 00, and soon collapse when that percentage is exceeded."

Jan 1, 1921

By Wils L. Cooley, Herman W. Hill

'The electrical behavior of ground beds is often quite different from what would be expected based on experience with electric circuits. An explanation for this unique behavior is given, through means of an analogy, which should promote intuitive understanding of ground beds. The nonmathematical development of the text is complemented by an extensive appendix which describes the details of ground bed calculations. This work was supported by U.S. Bureau of Mines contract G0144138.

Jan 1, 1979

By William A. Hoffman

In This Chapter [MSHA regulations for coal mines MSHA regulations for metal/nonmetal mines OSHA regulations for tunnel construction Types of respirators used in mines and tunnels Filter materials and filter efficiencies Donning, seal checking, and maintenance Filter service life and Respirator information resources] In many cases, engineering controls are not adequate to achieve satisfactory dust levels, so respirators must be used. This chapter explains the Federal regulations governing the use of dust respirators in mines and tunnels and describes the most common dust respirators used. Filter materials and filter efficiencies for respirators are discussed. This chapter also gives some guide-lines for respirator use and recommends sources for more dust respirator information. Respirator effectiveness in reducing dust exposure usually exceeds the effectiveness of most engineering control methods. RESPIRATOR REGULATIONS [Different regulations govern respirator use in coal mines, metal/nonmetal mines, and tunnels under construction.] Coal mines under Mine Safety and Health Administration (MSHA) jurisdiction. Coal mine operators are required to meet dust standards using only engineering control methods. Typical engineering control methods include ventilation and water sprays. Respirators are not regarded as an engineering control method, so respirators cannot be used in lieu of engineering controls.

Jan 6, 2003

By an Slo, J. J. Forbes

"INTRODUCTION This is the first of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal. These circulars are being published to focus attention of the coal-mining industry on this most prevalent source of fatalities and injuries and to present factual information that should be helpful in reducing loss from these causes.Records of fatal accidents in the coal mines of the United States, from all causes, have been kept since 1906; during this period approximately 30,000 men have been killed by falls of rock and coal in the bituminous-coal mines, and more than 7,000 men have lost their lives in the Pennsylvania anthracite mines from the same causes. From 1906 to 1930, about 900 men were killed annually by falls of rock and coal in bituminous-coal mines, and about 200 men were killed annually in anthracite mines during the same 25-year period. From 1931 to the present time, the number killed annually from falls of rock and coal has averaged more than 500 men in bituminous-coal mines and about 125 men in Pennsylvania anthracite mines.Numerically the record of accidents from falls of rock and coal shows improvement, but on a percentage basis and on a million-man-hours-of-exposure basis little, if any, improvement has been made during the past 40 years. The cold fact is that, year after year, about 50 percent of all those killed in coal mines in the United States lose their lives from falls of rock and coal."

Apr 1, 1948

By Richard J. Mainiero, Eric S. Weiss

This project investigates the behavior of blast waves from the detonation of high explosives in an underground mine. A series of explosive tests was conducted in the underground and surface facilities at the Bureau of Mines' Lake Lynn Laboratory to evaluate the potentially dangerous effects of blast waves produced by open shooting, blown out holes, or accidental detonations of explosives. Shots of C4 and TNT were fired at the dead end of a 6 ft high by 20 ft wide entry, at the intersection of two entries, and on the surface. C4 and TNT were chosen for this research because they exhibit very consistent performance. Behavior of the blast wave was evaluated through recording of the pressure as a function of distance from the explosive detonation. For both explosives, C4 and TNT, peak pressure decay with travel down the entry was inversely proportional to distance to the 0.9 power. When comparing pressure measurements at 200 versus 100 feet from the detonation; at 200 feet the pressure would be 1/2 0.9 or 54 percent of that measured at 100 feet. By comparison, peak pressure for a surface shot exhibits a decay with distance to the -1.6 power, yielding a pressure at 200 feet 1/2 16 or 33 percent of that measured at 100 feet. This result confirms that the blast wave from detonation of an explosive in an underground mine maintains its force for a greater distance than would be the case on the surface. Table and figures follow the text.

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958