Search Documents

A survey of roof and pillar conditions in underground limestone mines in the United States has revealed that bench mining of the floor between pillars can cause instability in the pillars at the perimeter of the benched area. Increased loading of these pillars was observed at several mines. Large inclined geological structures that are exposed in pillar ribs were observed to contribute to pillar instability. The paper describes a study that was carried out using numerical models to assess the effects of bench mining on pillar load and stability. It was found that the benched pillars shed load onto the surrounding pillars owing to their reduced stiffness. The pillars at the perimeter of the benching area will start shedding load as soon as benching increases the height of one side of the pillar. A case study is described which shows the effects of bench mining on limestone mine pillars.

Jan 1, 2007

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

6. Computer Simulation of Mine Evacuation Analysis of mine evacuation involves manipulating a large number of interacting variables, such as mine passages, hoist movements, miner position etc. , which makes the problem very difficult to solve without use of a digital computer. Therefore, under this contract, a computer program is written to simulate evacuation of a mine under different configurations. The simulation input variables include characteristics of the mine, expressed in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self-rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i. e , fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effect of the fire on ventilation or on the miners is not considered. The simulation output includes the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure time of the miners. Details of the mine evacuation program are summarized in Appendices A and B Appendix A describes structure of the program and its capabilities. The flexibility of the program and its suggested uses are demostrated by a number of illustrative examples Appendix B is a user' s manual for the program which includes instructions for program use and explanation of the logic employed in the program. A computer listing and printout of a typical output are also included in the Appendix B The ten illustrative examples summarized in Section A 4 (Appendix A) provide proof of validity of the program and help make certain inferences about mine evacuation. The first example, which is simulation of an actual mine fire drill conducted in a mine, has predicted evacuation time within 5 percent of the actual evacuation time in the fire drill, demonstrating thereby, the ability of the program to make accurate predictions.

Jan 1, 1976

By Kenneth J. Miller

The Bureau of Mines conducted an investigation to improve the flotation response of coals that are difficult to wash by froth flotation. A literature survey and experimentation showed that, for the most part, refractory coals can be floated with oily collectors and frothers. Collector reagent consumption can be minimized and the selectivity of the flotation enhanced by assuring adequate, but not prolonged, reagent conditioning. Where flotation selectivity is especially poor, two-stage rougher-cleaner flotation is recommended. It was concluded that a major problem with refractory coals is predicting when they will appear in a flotation circuit so that supplementary flotation collectors can be added. Coal losses due to variation in the floatability of the feed might be reduced if a nonpolar collector such as kerosine or fuel oil is used along with a frother as general coal flotation practice.

Jan 1, 1977

By Ben A. Kornhauser

The mineral industry consisted primarily of natural gas production and of urea fertilizer, which was manufactured for domestic agriculture. Copper and iron deposits were being developed. Information regarding the mineral industry of Afghanistan was sparse. The Government continued to emphasize the development of mineral resources that could benefit the economy of the U.S.S.R. and repay Soviet grants. The northern half of the country, north of the Hindu Kush mountain range and adjacent to the U.S.S.R., received considerable Soviet aid to develop mineral resources.

Jan 1, 1986

Table B-1. Summary of respirable coal mine dust samples collected under 30 CFR 90 by MSHA inspectors for underground occupations, 1988-92* [ ]

Jan 1, 1997

By Sean Gallagher, Rhys Llewellyn, Jay Mattos

This paper contains the results of an examination of accident, injury, employment, and production information reported to the U.S. Department of Labor's Mine Safety and Health Administration (MSHA) and provides information on some of the measures longwall mine operators are using to prevent accidents In all industries, technological advances play a key role in determining those who will survive as competitive participants in an increasingly global marketplace. While mining is among the most basic of industries, technological change is neither unfamiliar nor unwelcome to miners. Historically, technological advances in mining, particularly coal mining, have tracked closely with fluctuations in demand. In the early 1900's, coal accounted for more than three quarters of all the fuel consumed in the U.S. To meet this tremendous demand, underground cuffing machines were introduced, resulting in faster, more efficient coal extraction. Transporting coal to the surface, however, remained labor intensive. In the 1920's, nearly all underground coal was still being hand loaded. Demand for coal then declined as the price of oil, natural gas, and electricity became competitive. In the late 1930's and throughout the duration of World War II, coal demand and production was high. By 1940, more than half the coal mined was being mechanically conveyed to the surface. In 1948, the continuous mining method was introduced in the U.S., further accelerating the extraction process. By the 1950's and 1960's, however, coal production again declined as railroads converted to diesel fuel and gas and oil provided a larger share of the home heating market. Underground coal mines required even more mechanization to remain competitive as an energy source. The first longwall system was introduced in 1960. By 1995, longwalls were producing more than 189 million tons of clean coal annually, surpassing continuous mining production for the second straight year. The mining of coal and other materials has not come without a huge loss of life and considerable human suffering. More than 103,000 workers died from injuries in U.S. mines in the last 85 years. Between two and three thousand miners died each year from the turn of the century until 1931, many from underground fires and explosions. The U.S. has witnessed a tremendous drop in fatalities in underground coal mines. Credit for that is due to safety inspections and enforcement activities, better safety awareness and practices among management and labor, improved ventilation, the use of safer equipment, and increased mechanization which removed many miners from the hazards at the face and also reduced the size of the mining work force. There is little doubt that longwall mining has greatly increased underground coal mine productivity. The degree to which longwall mining has contributed to a safer work environment for underground miners is more difficult to ascertain.

By R. D. Currie

The practicability and dependability of two permissible methane-indicat- in detectors recently developed were proved conclusively by extensive tests in the return airways of all mines operating in the anthracite region in most of which samples and readings were taken with one or the other of the two in- dicating detectors. These detectors roved dependable and accurate within practical limits, and their general use should be encouraged as an aid to bet ter ventilation, more accurate control of air currents, and greater safety in mines.

Feb 1, 1936

By C. M. Mason

Mechanical mining produces large quantities of very fine coal dust called float dust. The associated increase in hazard requires a reexamination of the Bureau of Mines method of evaluating the incendivity of explosives in coal dust-gas-air mixtures. A technique recently developed by Bureau of Mines laboratories for evaluating the incendivity of explosives in coal dust-air mixtures was applied, with modifications, to coal dust-air-natural gas mixtures. A series of permissible explosives were evaluated by this modified technique. Results indicate that the modified technique could be the basis of a more discriminatory procedure than that presently in use.

Jan 1, 1968

By H. R. Shell

Variations between laboratories on the silica and alumina content of calcined kyanite led to this Bureau of Mines study of the extent and nature of the differences. In particular, Bureau scientists hoped the study would lead to correction of the causes of the dissimilarities. A sample of calcined Kenya kyanite was analyzed by seven different laboratories familiar with silicate analysis. The compiled data indicated differences originating from lack of recovery of silica after two acidic dehydrations, from high alumina caused by several factors, from loss or gain of iron during sample fusion, and from indifference regarding the accurate determination of minor constituents.

Jan 1, 1959

By Steven M. Shope

The Bureau of Mines electromagnetic trapped miner location and communications system requires a thorough understanding of through-the-earth electromagnetic wave propagation. An earth model incorporating a magnetic dipole buried in a three-layered earth has been developed. The dipole source is located in the second subsurface layer. By application of proper limiting values, the three-layered model is reduced to two different two-layered models and eventually to the homogeneous half-space model. The solutions are in the form of infinite integrals. A numerical analysis was carried out and a computer program written to evaluate the surface magnetic fields. Numerical values for the magnet- ic field at the point above the source are presented in a variety of models.

Jan 1, 1982

By A. R. Rule

Laboratory tests were conducted to study removal of magnesium impurities from western phosphate rock concentrates by selective leaching. The systems evaluated included leaching with dilute sulfuric acid, with ammonium sulfate, and in an aqueous medium with sulfur dioxide gas. Set standards for the magnesium impurity level of phosphate rock concentrates are not available, but industrial practice has indicated that magnesium in excess of 0.3 percent MgO causes problems in phosphoric acid manufacture. Removal of magnesium was accomplished with all three systems. With dilute H2S04 the magnesium level was reduced to less than 0.1 percent MgO with an accompanying P205 loss of 6 percent. Magnesium oxide levels from 0.3 to 0.2 percent were obtainable with ammonium sulfate. However, the system requires concentrate roasting at temperatures of 900° C or higher, heated pulps (100° C), and large quantities of ammonium sulfate. Selective leaching was obtained using S02 gas in an aqueous concentrate slurry. Magnesium oxide content was reduced to less than 0.1 percent without loss of phosphate.

Jan 1, 1970

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967

Miners, like everyone else, must be able to see well in order to work well. But simply hauling bigger and brighter lights into the mines does not necessarily produce better mine illumination. This chapter tells why. Increasing the power of the light source can create problems of portability, glare, adaptation and contrast. This chapter also discusses some ways to increase illumination by Improving the reflectability of walls, roofs and other exposed surfaces. In Chapter IV you learned that the "brightness" of a room or work area was really a matter of how much light was reflected from the walls, roof, and other surfaces. Therefore, if you want to Improve visibility you should increase the amount of reflected illumination. O HOW DOES ONE DO THAT? One way of Increasing reflected illumination would be to increase the power of the light source.

Jan 1, 1976

In the past, mine management has been concerned with removing water from active mining sections primarily because it hampered the movement of mining equipment and aggravated the working condition of the miners. Pumping water to sumps and gravity drainage by ditching have proven successful in mines for minimizing section down time due to water influx. However, with the advent of more strict pollution laws the mining engineer must now be concerned with keeping water out of the section and also with preventing it from causing pollution. A review of the handbooks and textbooks used in the mining engineering curricula reveals that little has been written concerning acid mine water prevention or control in underground coal mines. Additionally, the review of the curricula of mining schools indicates they are not teaching the engineering students the necessary techniques of mine water management as they relate to the abatement of mine water pollution.

Jan 1, 1970

By F. C. Gregory

"The ""safety bonus"" in metal mining is a sum in addition to the regular wage, paid to foremen or bosses for keeping the accident rate down to a specified minimum. It has been used with success for some time by certain companies as a regular part of their safety work. It is desirable from the employer's point of view in that the desired results in accident reduction must be accomplished before the bonus is earned; and from the standpoint of the recipient, in that he receives a reward for the additional effort which he has put forth in order to earn the bonus.While this paper relates to the safety bonus as applied in the metal mining industry, the bonus system discussed herein will apply equal well to coal mining, oil-field work, and other mineral industries.Various estimates have been made as to the percentage of accidents that can be prevented through physical safeguards, adoption of safe working methods, and other safety measures which can be initiated and carried out wholly through the management or the safety department. This percentage will always be a vari¬able according to the local plant and conditions. But all who have been engaged in accident prevention agree that such work alone cannot bring the accident fre¬quency down to where it should be, and that it is very necessary to work directly with the workmen, in an effort to make each individual do his share in making the work safe. In this latter phase of the work, the boss who has immediate super¬vision of the men is the one who can do the most, since he is in daily and frequent contact with the men while they are at work. In the metal mines, the shift and stope bosses are the key men; in the oil fields, the ""tool-pushers"" or sub-foremen, and the same applies to all industries. So it becomes necessary to keep these sub-foremen constantly interested in accident prevention, both because they are in personal touch with the men and because they are responsible for production and hostile to any plan which they think will interfere with their output. In large organizations it is the shift boss who represents the company and its policies to the man on the job."

Jun 1, 1924

By J. E. Pahlman

The Bureau of Mines conducted re-search to determine the resistance of basic refractories to corrosion by ash slags that would result from the burning of coal and lignite in metallurgical operations. Basic refractories are of economic interest because they are from one-third to one-half as expensive as 90-to 99-pct-alumina refractories. Static tests were performed at 1,300° C and dynamic tests at 1,400° to 1,650° C to investigate the stability of refractory specimens in a slag environment. In alkali-containing lignite ash slags, in order of decreasing resistance, magnesite, magnesite-chrome, and chrome-magnesite refractories all had corrosion resistances equal to or better than 90-to 99-pct-alumina refractories. These basic refractories formed slag penetration layers in dynamic tests, which helped protect them from further attack. Chemically bonded basic refractories in general did not have as good a resistance to slag attack as did burned refractories of the same composition. In very acidic coal ash slag, a chrome-magnesite refractory containing 30 pct MgO plus a slag inhibitor and direct-bonded magnesite-chrome refractories with 60 pct MgO had good resistance to attack. Chrome-magnesite refractories (30 to 40 pct MgO) were moderately to severely attacked, and refractories with greater than 70 pct MgO were severely attacked by this same slag.

Jan 1, 1982

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By C. E. Brechtel

Cooperative research efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, used a one-dimensional, finite-element computer model to simulate turbulent mass transfer in face ventilation of oil shale mines. The objective was to study the dilution of methane released by rubbled oil shale during blasting. A methane release rate function was developed from the back-analysis of field measurements, and the finite-element model was calibrated using tracer gas characterization data from tests of full-scale face ventilation systems.

Jan 1, 1989