Search Documents

By M. M. Fine

A satisfactory mean: of beneficiating a Brazilian phosphate rock was developed in a mineral-dressing-research study by the Bureau of Mines. High-grade concentrates well ever the specified minimum grade of 70 percent tricalcium phosphate, were produced, with goad recoveries by agglomerate tabling and flotation. A lower gads but usable secondary product was recovered by sedimentation of the minus-200-mesh fraction of the ore. The ore wan representative of an extensive deposit recently discovered near Recife in the State of Pernambuco, Brazil, which will be exploited in a plant planned to eventually produce at the rate of 500,000 tons of concentrate annually. Although Brazil has been reported to Lave a substantial reserve of phosphate rock,3/ the country has never been more than a small producer of this commodity. From 1945 to 1950 the highest production of phosphate rock attained in Brazil amounted to 10,421 tons. Production in 1949, the most recent year for which figures are available, was 4,553 tons.4/

Jan 1, 1954

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By George J. Conroy

This Bureau of Mines publication describes several fault locators and methods, including time domain reflectometers, a frequency domain reflectometer, tone generators, an infrared method, the Murray loop method, and high-voltage "click" methods. The Bureau of Mines has been conducting research into these methods for several years, to improve mine safety and facilitate production through rapid, safe location of trailing-cable faults. The problems encountered in practical applications are discussed, and schematic diagrams of several instruments fabricated by the Bureau are presented. Since no present single method of locating trailing-cable faults is universally applicable, a kit composed of several of the more promising fault locators is advisable.

Jan 1, 1978

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By Raymond L. Carpenter

In connection with its continuing studies of the characteristics of alloys and alloying elements, the Bureau of Mines investigated the crystal structure of fused boron. This report describes how the structure of fused boron was found to be rhombohedral by the powder method for crystal-structure determinations by X-ray diffraction. The determinations of the crystal structure of boron reported in the literature were made on crystals prepared by various methods such as electrolysis, thermal decomposition of a boride, or by hydrogen reduction of boron tribromide. Table 1 summarizes the data found in the literature on the crystal structure of boron. The information shows the following: (1) Three structures have been reported for boron, (2) boron prepared by different processes--or even by varied conditions of a process--produces crystals of different structure, and (3) no information is given on the crystal structure of fused boron.

Jan 1, 1960

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By R. L. Montgomery

Electronegativities of the rare-earth elements were calculated from heats of formation. The values obtained from different compounds varied widely. The postulates of Pauling's electronegativity theory were interpreted for bonds that are primarily ionic; the study showed that many compounds obey rules of the form expected. Revised electronegativity values are given for the more electropositive elements, including the rare-earth metals (which are near magnesium in electronegativity). Estimates of un-known heats of formation are made from electronegativities and are compared with other estimates. INTRODUCTION Calculation of the electronegativities of the rare-earth elements is interesting to show how these metals stand relative to the other metals and to each other, and also possibly to systematize the thermochemical data on them.

Jan 1, 1960

By Robert C. Hickman

"INTRODUCTION The Cline mine has been worked intermittently for copper and gold since 1895. Scheelite has recently been detected with the aid of a ""Mineralite"" on the old waste dumps of the mine. Four diamond-drill holes were drilled by the Bureau of Mines from August 13 to September 25, 1946. Results of this drilling showed the vein to pinch at depth and to carry no mineralization of economic importance.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigation work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.Acknowledgment is due Dr. Jasper L. Stuckey, State geologist, for logging the drill core and to J. B. Zadra and associates, Metallurgical Branch, College Park, Md., for analytical determinations."

Feb 1, 1948

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

By Ryron O. Pickard

"The Berkeley safety station of the U. S. Bureau of Mines was recently informed that a geologist was killed through entering an abandoned 90-foot exploratory shaft without making a preliminary test of the shaft atmosphere. He was one of a geological party which was investigating coal lands in California. The only light that he carried into the shaft was an electric flash light. After he had descended a short distance, one of his associates on the surface heard him exclaim, ""This place is full of gas, I am coming up"", He had no more than finished the remark when he was seen to lose his grip on the ladder and fall down the shaft. He was apparently weakened from impure air in the shaft, and could no longer suppers himself on the ladder. When his body was recovered, it was found that his neck had been broken by the fall.This is the ;second recent accident that has been called to the writer's attention where a life has been lost in abandoned exploratory workings; the other fatality being in Minnesota where a mining engineer was overcome while sampling a shallow pit in iron-ore formations. This engineer was on the bottom of the shallow pit and died before help could reach him. It was generally supposed that each of these deaths were due to poisonous gases, but the writer believes, after reviewing the information available, that death in both instances may have been directly caused by deficiency in oxygen.Frequently in the daily press there are items relative to lives being lost through cleaning out old wells, and as a general rule such accidents are also caused by impure atmospheres.In every abandoned shaft or pit, or in fact, any old working where the air has been stagnant for a considerable time, there is always danger of oxygen deficiency, as the oxygen which originally comprised one-fifth of the atmosphere may be appreciably replaced by gases that do not support life, usually by carbon dioxide (black damp) or methane (fire damp). Much valuable information on the subject of mine atmospheres, mine gases, and the effect of oxygen deficiency onthe human system is contained in Miners' Circular 14, ""Gases Found in Coal Mines"" by G.F. Burrell and F. M. Seibert; Technical Paper 122, ""Effects of Oxygen Deficincy on Small Animals and Men"", by G. A. Burrell and G. G. Oberfell; and ''Chit of Properties of Mine Gees"" by G. A. Burrell. These publications of the Bureau of Mines should be rent by all who are interested in the subject of this paper."

Nov 1, 1921

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

By R. B. Schluter

The Bureau of Mines investigated the flotation responses of two copper-nickel ore samples from the Duluth Complex with the objective of recovering bulk sulfide concentrates. One of the ores studied was taken from a test pit; the other was taken from a test shaft. The samples were quite similar except that the pit sample analyzed 0.35 pct Cu and 0.11 pct Ni and the shaft sample analyzed 0.69 pct Cu and 0.14 pct Ni. Flotation responses were studied in both laboratory and pilot plant tests. Pilot plant flotation responses were similar for both samples resulting in grades of 12.2 pct Cu and 2.5 pct Ni for the pit sample and 12.2 pct Cu and 2.1 pct Ni for the shaft sample. Weight recoveries were 2.5 pct for the pit sample and 5.2 pct for the shaft sample. Copper and nickel recoveries for the pit sample were 87 and 62 pct, respectively, and 92 and 73 pct for the shaft sample. Both concentrates contained small but significant values of cobalt and precious metals. Cobalt recoveries were low--less than 40 pct for both concentrates. Precious metals contents of the concentrates were 1.59 oz/ton for the pit sample and 0.99 oz/ton for the shaft sample. Silver was the predominant precious metal by weight, but platinum and palladium represented the highest values.

Jan 1, 1980

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By E. G. Valdez

Iron foundries that melt automobile scrap produce flue dusts averaging about 32 percent zinc and 6 percent lead. Some is sold to smelters, but because of the meager return and difficulty in handling, most of the dust is discarded. As part of the Bureau of Mines program to find uses for mineral wastes, research was initiated to develop an economical process to recover zinc and lead from the flue dust. Research encompassed the extraction of zinc and lead by fuming, leaching, and agglomeration. Controlled vacuum fuming of zinc to produce Prime Western zinc and a lead-rich residue was the most effective method for treating the dust. This process involved two distillations, or fumings, with carbon and methane as reductants, and resulted in recovery of 91.4 percent of the zinc in a Prime Western grade product, and 98 percent of the lead. Hydrometallurgical techniques involved several leaching methods, but the simultaneous extraction of iron, manganese, and copper resulted in contamination of the solution and made the zinc recovery processes too complicated. Agglomeration was done by pelletizing or briquetting the dust for possible use as feed to a zinc smelter.

Jan 1, 1975