Search Documents

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire injuries that occurred in underground metal/nonmetal and stone mines by state during 1990-2001. Table 1 also shows the injury risk rates, employees' working hours, and lost workdays. Overall, 65 fires occurred in 20 states; these include 2 fires and no injuries for contractors. Six of the fires caused nine injuries. The yearly average was 5.4 fires and 0.75 injury. Forty-one fires with 2 injuries occurred in metal mines, 14 fires with 7 injuries occurred in nonmetal mines, and 10 fires with no injuries occurred in stone mines. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations. The Ewhr value was 260 x 10° hr (Irr = 0.007), and the LWD value was 83. Idaho had the most fires (eight fires and no injuries), followed by Louisiana (seven fires and two injuries), Michigan (six fires and six injuries), and Missouri (six fires and no injuries). Of these states, Michigan had the highest injury risk rate value (Irr = 0.146). Table 2, partly illustrated in figure 2, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires during the six time periods show an increase during the fourth period followed by a sharp decrease during the fifth period and a sharp increase in the last period. The number of fire injuries show an increase followed by a decrease during most of the periods, accompanied by a decline in employees' working hours during most of the periods; an increase is seen during the third and fourth periods. The In values follow patterns similar to those shown by the injury values. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables related to fires for 1990-2001. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Irving Hartmann, Bernard Lewis, John Nagy, H. P. Greenwald, H. C. Howarth

"ORIGIN OF INVESTIGATIONThe Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States, July 24J 1946, contains the following provisions with regard to rock dusting: Article VI. - Section 2. Rock dusting.(a) All mines, except those mines or those locations in a mine which are too wet or too high in incombustible content to propagate an explosion, shall be rock-dusted to within 80 feet of the faces of rooms and entries; however, if the mine or any part of it is wet but becomes dry, the mine or portion of the mine so affected shall be rock-dusted as ·soon as it becomes dry. (b) In mines partially rock-dusted or in mines that are required to start rock dusting, haulageways and parallel entries connected thereto by open crosscuts shall be rock-dusted. Back entries shall be rock-dusted for at least 1,000 feet outby the junction with the first active entry. Inby this junction, the rooms, entries, and crosscuts shall be rock-dusted by generalized rock dusting as provided for in section 2(a).(c) Where rock dust is applied, it shall be distributed upon the top, floor, and sides of all open places and maintained in such quantity that the incombustible content of the mine dust will not be less than 65 percent. In trackless entries and air courses, protection in lieu of generalized rock dusting may be had by using bags filled with rock dust, if they are placed at regular intervals and staggered as described in Bureau of Mines Report of Investigations 3411."

Feb 1, 1948

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

The National Institute of Occupational Safety and Health has classified diesel exhaust as a potential human carcinogen. Though standards for diesel particulate matter (DPM) in the work place have not been established, concern for the health of miners is prompting mine operators to consider methods for reducing worker exposure to diesel exhaust. Approach One of many methods for reducing DPM being investigated by the Bureau of Mines is the use of additives in diesel fuel to improve combustion. Research Results Three fuel additives have been tested in Caterpillar and Deutz diesel engines which are similar to types used in underground mines. One iron-based additive containing ferrous picrate had no effect on emissions. A second iron-based additive containing ferrocene reduced DPM between 5 and 45 pet depending on engine operating conditions. The 37-pct reduction for an 8-minute duty cycle, which includes a wide range of transient loads and speeds, is considered to represent in-mine performance.

Jan 1, 1990

By Fred R. Biggs

This report was prepared by the U.S. Bureau of Mines to present a brief history of the listing of Iron Mountain Mine as a Superfund site on the National Priorities List (NPL) and subsequent remedial actions. The mine area is located on 4,400 acres near Redding, CA, and includes underground workings, an open-pit area, waste rock dumps, and tailings piles. This property involves multiple sources of acid mine drainage (AMD) that are high in copper, zinc, and cadmium. The selected remedial actions, based on the Record of Decision of 1986, would partially cap the Richmond mineralized zone to reduce infiltration of clean water, divert clean surface waters away from contaminated areas, fill surface subsidence areas, and enlarge the Spring Creek debris dam to provide increased surge capacity. Site remediation efforts at Iron Mountain are well into the remedial design-remedial action phase. Costs to date for remedial action are $7.5 million. Details of activities and designs of remedial elements are presented and future activities discussed.

Jan 1, 1991

Because surface mining removes the original plant cover from the land and exposes the soil, special care is needed. Until the mined land is stabilized by revegetation, snowmelt and rainfall can pick up sediment and erode mined lands much faster than undisturbed areas. Sediment control is an important aspect of protecting the environment during mining and reclamation because without it, large amounts of sediment can clog streams, increase the risk of flooding, damage irrigation systems, harm aquatic habitat, and limit the use of water for other purposes. Stream quality can be affected many miles downstream from the mine. Before SMCRA was implemented many streams were degraded by uncontrolled sediment from mining. Sediment is controlled through careful planning and a design that incorporates a variety of measures that work together to reduce soil erosion at the mine. Disturbed areas are graded, and some areas terraced, to achieve stable slopes, reduce runoff water velocity, increase infiltration, and divert runoff into drainage channels so that it flows away from unvegetated, erodible areas. Grading along the slope contour and scarify in gun vegetated slopes with bulldozer track marks help prevent erosion by slowing down the flow of water. Runoff from haul roads is controlled by culverts and roadside ditches. Sedimentation ponds or other forms of sediment control are required at all mines to minimize the amount of sediment leaving the site.

Jan 1, 1992

By H. Kenworthy

The objective of this research was to develop methods and determine conditions under which metallic sulfides with lower boiling points than sphalerite may be removed from zinc sulfide concentrates by volatilization. A higher percentage of extraction of lead, cadmium, and germanium than is common in current practice was sought. The investigation, conducted by the Metallurgical Branch of the Minerals Technology Division, Region VI, showed that, under proper conditions, it is possible to remove over 90 percent of the lead, cadmium and germanium as an enriched sublimate. The uses of lead, and cadmium to a lesser extent, are well-known. Although germanium was discovered in 1886 by C. Winkler, commercial use has been achieved only in recent years. The amount consumed per manufacturer unit is so small that the price of germanium may still be quoted by the gram. The electronic industries have been the chief consumer of this semiconductor. Germanium is sold largely to the fabricator as a dioxide for reduction to metal and subsequent processing into wafers for use in diode and triode electronic tubes. Extensive research at Purdue University during World War II led to the first practical use of germanium.

Jan 1, 1952

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By W. H. Young

THE BITUMINOUS coal and lignite industry declined slightly in 1961, compared with the 1960 figures. All of the major items, production, consumption, average value, exports, and employment, declined. Even the steady upward trend in mechanization failed to materialize; the percentages of total tonnages mechanically loaded and cleaned remained the same as in the preceding year. However, tonnage per man per day increased from 12.83 tons in 1960 to 13.87 tons in 1961, owing partly to the increased tonnage produced by continuous mining machines. Also, the percentage of total production mined by stripping and by augers increased slightly. Production.-The output of bituminous coal and lignite in the United States in 1961-403 million tons-was 3 percent less than the 416 million tons produced in 1960. Production was retarded in 1961, owing largely to the business recession and reduced exports.

Jan 1, 1962

By R. B. Corbett

"INTRODUCTION Aluminum and manganese bronzes as a group, may be separated readily from other copper-base alloys by experienced sorters. However, separation of aluminum bronze from manganese bronze is generally a matter of guesswork, so that accurate separation presents a difficult salvage problem.Attempts at separation by the thermoelectric tester. 3/ which had proved successful in solving other sorting problems, showed in this instance that the desired separation was uncertain because of the wide range of composition allowable in each kind of bronze. If only one composition of each kind of bronze were used in industry, separation by the thermoelectric method probably would be simple. However; the variability in composition observed in commercial alloys is so great that the thermoelectric power of the one type frequently overlaps the range of values found for the other. As a result, specimens frequently are classified in the' wrong group.Separation of the two types of bronzes on the basis of measurements of magnetic properties on filings from the various samples also proved unsuccessful because the test results overlapped to such an extent that no clear-cut division could be obtained.Electrode potential measurements were made also on the aluminum and manganese bronzes in the hope of distinguishing between them. A drop of saturated potassium chloride solution was placed on the fresh surface of the metal and the tip of a calomel electrode introduced therein. The voltage generated was measured by connecting the electrode and the bronze part to a research-type potentiometer. Although the voltages generated by the manganese bronze parts were greater than those generated by the aluminum parts, the difference in the closest two sets of readings was not sufficient to warrant a good separation. When a concentrated potassium alum solution was used instead of the potassium chloride solution, a wider divergence of voltage was produced by the various bronzes, but unfortunately readings overlapped in several instances."

Nov 1, 1944

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees' working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By A. Bartkowiak

The lower flammability limit of methane at 0 p.s.i.g. and ambient temperatures is 5.6 volume percent in chlorine, 5.2 in oxygen, and 5.0 in air. The corresponding upper limit values are 70, 60.5, and 15 volume percent, respectively, so that the range of flammable mixtures is greater in chlorine than in oxygen or air. The lower flammability limit of ethane at 0 p.s.i.g. and ambient temperatures is 6.1 volume percent in chlorine, 3.0 in oxygen, and 2.9 in air. The corresponding upper limits are 58, 66, and 12.5 volume percent, respectively. In this instance the range of flammable mixtures is greater in oxygen than in chlorine or air. Generally, the limits of flammability for both methane-chlorine mixtures and ethane-chlorine mixtures widen with increases in temperature and pressure.

Jan 1, 1960

By H. H. Fields, Stephen Krickovic, M. G. Zabetakis, Albert Sainato

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot -deep vertical borehole. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the corresponding values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

ESTABLISHMENT of an effective inspection system has been held essen¬tial to any international agreement that may be designed primarily to curb the testing of nuclear weapons. A number of reports and papers already have described basic inspection concepts and appraised various pro¬cedures, techniques, and methods as to their probable effectiveness in detecting and identifying violations under such agreement. This report results from a study of only one part of the contemplated inspection system, specifically the final phases embracing onsite investigations and mine examination techniques. The results and reports of earlier work were reviewed in detail, and subjects that were found to have been exhaus¬tively evaluated are recognized by reference and not redescribed here. In other instances, previously described techniques, methods, and clues were revaluated to define more clearly their practical value to the final objective of an onsite inspection. Previous documentation does not refer to a number of subjects, techniques, tools, clues, and methods considered by the study; this report treats these in detail, even though when applied singly or collectively their practical value may be questionable.

Jan 1, 1962

By James R. FitzSimmons

This report describes an instrument developed by the Bureau of Mines as an improved device for examining roof rock in bolt holes. The unit consists of a commercially available fiberoptic unit adapted for use as a flexible stratascope. Field testing in both metal and coal mines has shown the instrument can be easily transported and used by a single operator. The size and flexibility of the instrument eliminate the need for specially drilled holes.

Jan 1, 1979