Search Documents

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By John Nagy

Limited experiments in the laboratory with specimens of mine rock from a Virginia bituminous coal mine indicate that natural gas-air mixtures can be ignited by sparks generated by rubbing friction of sandstone against sand-stone, shale against sandstone, sandstone against (roof-bolt) steel, and shale against steel. Such sparks, generated during a roof fall, may have initiated a recent gas explosion in this Virginia mine, although this cannot be stated with certainty. No ignitions of gas were produced by sparks or heat generated by impact friction between mine rocks or steel, during tension breaks of roof bolts, or by pull tests of roof bolts through their washers and roof plate. However, this negative result of limited experiments does not preclude the possibility of gas being ignited by these conditions.

Jan 1, 1960

By C. W. Owning

"The Bureau of Mines has repeatedly emphasized the necessity of completely ""rock-dusting all coal mines, except anthracite mines, in every part whether in damp or dry condition."" Every open accessible part of, the, mine without exception should be thoroughly rock-dusted, including parallel entries, air courses, trackless entries, crosscuts, and rooms to within at least 40 feet of every coal face. Very few mines have followed this recommendation and warning, with the result that there have been explosions not only in mines which have not used rock dust but also in so-called rock-dusted mines. Following a number of mine explosions it has been reported that the mine was rock-dusted,"" whereas it is probable that only some of the haulage roads had been given a hurried application of rock dust and in most instances not as much as 5 per cent of the mine was really rock-dusted. That is not rock-dusting.Some conscientious, well-meaning mining men have felt that rock-dusting of haulage roads would effectively stop an explosion; however, when shown, through widespread explosions in mines ""well rock-dusted"" according to the above method, that leaving large areas undusted, furnishes paths through which a violent explosion may travel, these mining men have realized the necessity of thorough rock-dusting and have adopted this explosion-prevention method.The Mather Collieries mine, Pickands, Mather and Co., operators, at Mather, Pa., was the first mine in Pennsylvania to receive, full credit for rock-dusting under the new 'stringent ruling of the Pennsylvania Compensation Rating Bureau, the provisions of which require that:"

Feb 1, 1931

Provide an environmentally compatible means of producing lead from galena concentrates that replaces the current high-temperature pyrometallurgical primary lead smelting process and supplies pure lead metal within present and proposed Environmental Protection Agency (FPA) and Occupational Safety and Health Administration (OSHA) lead emission standards. Approach The U.S. Bureau of Mines developed an energy efficient and pollution-free leach-electrowinning method for use in recovering pure lead metal and byproducts from lead sulfide concentrates.

Jan 1, 1989

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By Walter W. Fisher

Cement copper was flash roasted in a vertical tube furnace to convert the copper to acid-soluble oxides as part of a postulated process for refining cement copper by oxidation roasting, acid leaching, and electrowinning. The results of the study showed that the oxidation was a linear function of oxygen concentration between 0 and 20 percent, but above 20 percent oxygen there was no further increase in oxidation. Therefore, air was the optimum oxidizing atmosphere in this flash roasting system. The oxidation followed a parabolic rate law as the roasting temperature was increased from 400° to 800° C. Extrapolation of the data, based on the parabolic law, indicated that at 400°, 500°,600°,700°, and 800° C, the roasting times required for complete conversion to soluble oxides were 75, 37, 21, 7.7, and 4.6 seconds, respectively. Cyclic-roasting test results did not substantiate the predictions obtained through data extrapolation.

Jan 1, 1973

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By L. C. IlsLey

"According to accident statistics, issued from time to time by the Department of the Interior, Bureau of Mines covering fatalities in coal mines, between the years 1870 and 1921 there were 4,897 deaths caused by explosives. The legislatures and safety commissions of the various mining States have Elected and formulated many excellent regulations in regard to the handling and use of explosives in an endeavor to keep this class of accidents as low as possible. An analysis or comparison of the explosive, regulations issued by over thirty States would make a very long paper, however, by subdividing according to phases and issuing several papers it is believed that the material will be more readily available. The first phase was treated in Serial No. 2405 of the Bureau of Mines (""State and Federal Electrical Shot-Firing Regulations,"" issued in October 1922) which gave a compilation of such regulations as apply strictly to electric shot-firing. The second phase under consideration is ""Who may set off blasts in coal mines.""In some States, the person who does the firing must be an ""authorized shotfirer,"" while in other States he must have proved his ability to do this work, and again in other States he is ""any person."" The present paper covers rules and regulations relating to this phase of shotfiring, and those States having similar regulations have been grouped as follows."

Jun 1, 1923

By Oliver Bowles

The exingencies of a world war have brought home to the American public, especially the people of the. Eastern States, the urgent need for conserving fuel. Transportation problems in the East have created an unprecedented situation wherein fuel-oil supplies are greatly restricted, and the consequent increase in demand for coal further complicates the problem of transporting and storing that commodity. People should awaken to the need for utilizing every possibly means of conserving to fuel, even to the extent of reducing the temperature in their homes.

Jan 1, 1942

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to January 1, 1925, was published in Bureau of Mines Technical Paper 3761. The present list includes all equipment tested and approved by the Bureau, up to and including January 1, 1926, and supersedes the list issued as Serial 27202 in November, 1925. It covers electric air compressors, coal drills, mining machines, mine pumps, room hoists, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamp, methane indicators and detectors, blasting units, storage battery loco- motives, power trucks, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manu- facturer, after his equipment has passed certain tests prescribed by the bureau, to mark his equipment with a seal showing that it has been "approv- ed" by the Bureau of Mines. The tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Feb 1, 1926

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

By William Eathorne

"INTRODUCTION Retsof mine, adjoining the village of Retsof, Livingston County, New York, is about 5 miles northwest of Geneseo and 55 miles (air-line distance) due east of Buffalo. It is a single-bed rock-salt mine having extensive horizontal workings as much as 2-1/2 miles long and 1 mile wide and has been in continuous operation since 1885. Retsof tine is the largest producing salt mine in North America and is reputed to be the largest active salt mine in the world.Retsof is one of three large salt mines operated by the International Salt Co., Scranton, Pa.; T. Forster Courthope is general manager of Retsof and also of the company's Detroit salt mine in Michigan and has held that position for 27 years. He is assisted by Stanley Martin, general superintendent; R. Goetz, Maintenance superintendent; and John Riordan, mine superin¬tendent. All are old-timers at Retsof and, according to Courthope, contri¬buted the ""lion's share in bringing the mine to its present standard of safety.ACKNOWLEDGEMENTThis circular was made possible by the generous cooperation of T. Forster Courthope and his assistants, Stanley Martin, R. Goetz, and John Riordan. The information and time generously given are gratefully acknowledged.GENERAL INFORMATIONThe rock salt as mined contains about 99 percent sodium chloride and requires only crushing and screening to prepare it for the market. With the exception of a large jaw crusher underground, all crushing is done in a mill building attached to the headframe of the main hoisting shaft (fig. 1).Five sizes of salt are produced, ranging from about 1/2 inch diameter down to minus seven mesh."

Sep 1, 1949

Water pollution has been an integral part of most mining operations in the past. Most mine planners had designed their mining operations with little or no regard for prevention of water pollution. The main planning element was always the economics of mineral recovery. Quite often the cheapest means of mineral recovery resulted in the largest water pollution problems. Recent water pollution laws have introduced a new economic element - water pollution control costs - to be considered in mine planning. Water pollution control costs can be extremely high. Foresighted planning can minimize these costs and provide better water pollution control. Effective pollution control preplanning can eliminate pollution from active mines and minimize pollution that may occur after completion of mining. Presently available technology can practically eliminate water pollution by treatment of the mine water. Use of water treatment during mining has no effect on the levels of water pollution after treatment ceases and the mine is abandoned. Therefore, this section of the report deals with preplanning to reduce water pollution, both present and future, by using at-source control techniques. Proper planning of mining and pollution control techniques should follow the concept of a complete, comprehensive reclamation plan. This plan should have control measures designed for all phases of mining from initiation through completion. Preplanning involves acquiring complete information concerning the future mine site, defining the reasons why mining could cause pollution from the site, and determination of available techniques to prevent or minimize formation or transportation of pollutants. Location of haulage and access roads and other mine related facilities should be included in preplanning for water pollution control. Mine site planning is the primary step in establishing any new mining area and is the key to a successful, non-polluting and economical

Jan 1, 1973

By M. Howard Berliner

"INTRODUCTION During the last 4 months of 1943, the Bureau of Mines engaged in an investigation and exploratory drilling program in the area between the Coughlin and Galena Level mines near the town of Shullsburg, in Lafayette County, Wisconsin. The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wiscon¬sin at a time when an effort was being made to increase the production of metals important to the Nation's war program.The portion of the southwest Wisconsin zinc district in the immediate vicinity of Shullsburg and the Coughlin and Galena Level mines is well mineralized. The principal ore horizon is at shallow depth, and there is evidence that relatively extensive surface mining for lead was done over a period of many years. Underground mining' for lead and zinc has continued to the present time.The Bureau undertook an exploratory drilling program in the area immediately west and southwest of the Coughlin mine workings after thorough preliminary investigations and geologic studies indicated that such work would serve to guide operators in the development of new ore reserves needed for continuance of mining operations in that area."

Apr 1, 1947

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By John W. Taber

"INTRODUCTION AND SUMMARYDiscovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits, appear to be sharp-walled, low-angle, tabular ore bodies in granite and are at least 10 feet thick.The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaFp and 1.44 percent SiO2.Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3."

Oct 1, 1952

By Dean H. Ambrose

This Bureau of Mines publication summarizes the status of mine electrical equipment reliability research. Failure rate data were estimated from theoretical, laboratory, and field studies. Tables are presented listing reliability characteristics of molded-case circuit breakers, undervoltage relays, ground check monitors, cables, motors, and control circuitry. Application of failure rate data is shown in tables listing maintenance scheduling intervals of components and components that are most sensitive to the probability of hazardous voltages on power distribution systems in the mines. Complete, accurate, and appropriate failure rates on mine equipment are of the utmost importance for reliability evaluations.

Jan 1, 1985

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932

By Constantine C. Popoff

During 1946 several high-grade limestone deposits in western Washington were examined by the Federal Bureau of Mines. The purpose of the examinations was to disclose new sources of industrial limestone and to indicate the commercial potentialities of little-known and undeveloped deposits. These examinations were part of a long-range program of investigation of mineral resources of the Pacific Northwest. The following report on the Whitechuck travortine deposit is one of a series prepared in the course of the investigations.

Jan 1, 1949

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Network analysis of mine ventilation systems is not new, having been traced back to 1854. A Committee Report (1970) has also reported the extensive work done in this respect in the United Kingdom, Japan, U.S.S.R., South Africa, United States, and other countries. Wang, et al (1970) developed a computer program which is an improvement over the earlier one developed by Wang et al (1967). The program has been recently modified and extended to include methane emission features by Owili-Eger (1973). This computer program incorporates all the novel features of the earlier programs. These include the capabilities of mesh selection, free splitting, internal or external fans, natural ventilation pressure and fixed quantity branches. The program is written in Fortran IV and, in effect, is an experimental mine in which many ideas can be tried out. The computer produces, besides the input data and certain computational data, the quantities and head losses in the branches, the head losses to be adjusted in the fixed quantity branches and the fan operating point. The last named program, hereafter to be referred to as the PSU/MVS, is presented in Appendix I. The application of this program is demonstrated in this manual through a series of selected examples. Application of the methane generator program is not included here as a detailed report on the subject is available elsewhere (Ramani et al, 1975).

Jan 1, 1975