Search Documents

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

The objective is to provide effective training on refuge chambers for underground coal miners. This training will increase knowledge about how to teach miners to operate, transport, and inspect a refuge chamber; what to expect psychologically and physiologically inside a refuge chamber; and how to decide when to use a refuge chamber. Background During 2006?2007, several disasters occurred at U.S. underground coal mines, resulting in 28 fatalities. These disasters led to new approaches to mine safety and health, as well as new federal regulations. One new technology mandated by federal legislation is the refuge chamber. Refuge chambers are movable shelters that are either made of steel or inflate from a steel skid as a tent. They can potentially save the lives of miners during an underground mine emergency by providing breathable air, food, water, and a safe environment for up to 96 hours. Because the refuge chamber is a new technology, recommendations, information, and training products are greatly needed.

Nov 1, 2009

To help mine safety and health professionals manage and reduce hazardous noise exposure with a software tool that simplifies the record-keeping and analysis process. Background Hearing loss resulting from overexposure to noise continues to be a problem throughout the U.S. mining industry. Studies indicate that 70%?90% of all miners have a noise-induced hearing loss severe enough to be classified as a hearing disability by the time they reach retirement age. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software program. DOSES is designed specifically for use by mine management and safety personnel to simplify the record-keeping and analysis associated with time-motion studies, making it easier to identify and solve noise exposure problems.

Jul 1, 2009

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By John H. Soulé

"INTRODUCTION Spodumene and lepidolite were shipped from the Harding pegmatite deposit, Taos County, N. Mex., in the period from 1930 to 1930. Tantalum minerals were noted as early as 1924 and described in 1931 3/ but no tantalum ore was shipped until 1942. The deposit was mapped and studied by geologists of the Federal Geological Survey and engineers of the Bureau of Mines late in 1942 and early in 1943, and a Bureau of Minus exploratory project was carried out in 1943. 4/ Thu following report presents the results of that project.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Minos has as its primary objective the more effective utilization of our mineral resources to the end that they make the greates possible contribution to national security and economy. It i the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lovell B. Moor, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallugiical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By Stephen D. Cramer

A nondestructive procedure for measuring electrodeposit porosity has been developed which records the location and number of deposit defects including pores, pits, and voids. The procedure involves the passage of an X-ray beam through the deposit-substrate system onto suitable film. The defects are recorded as images on the film. Variables studied included intensity and spectra of the X-ray beam, composition and thickness of deposit and substrate, film type and developing procedure, and limits for detecting defects. At an X-ray tube voltage of 40 kv, pores several mils thick were easily detected in copper-nickel specimens more than 20 mils thick. To illustrate the utility of the procedure, the effect of substrate oxidation and of current density on electrodeposit porosity was briefly studied.

Jan 1, 1970

Researchers with the National Institute for Occupational Safety and Health (NIOSH) have developed a training module to educate both new, inexperienced miners as well as veterans on important issues related to self-rescue and escape procedures. These include: (1) physical and environmental conditions that can be encountered in a mine after a major explosion, (2) knowledge of emergency meeting locations and escape routes, (3) the importance of using self-rescuers, even in seemingly clear air, to keep the lungs isolated from contaminants, and (4) why miners should not go off to look for others who are missing. In addition, the module may stimulate miners to think about and discuss mine explosions and the devastating effects of such an event.

May 1, 2009

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By Joseph B. Cummings

The Twin Buttes camp embraces eight mines in the Pima mining district. The first mining claims in the camp are said to have been located in 1876, but little mining was done until 1905. Intermittent operation of five of the mi.nes to 1928 yielded 388,231 tons of ore averaging 6.19 percent copper and 8 small tonnage of high-grade oxidized zinc ore. While the Bureau was investigating the area, one mine was active, and it started to produce in 1944. The mines of the Twin Buttes camp are at or near contacts of intrusive granite with Paleozoic limestones and quartzite. The ore shoots lie in metamorphosed sediments adjacent to a zone of garnet rock that separates the ore from the footwall granite. Small fissures that originate at the contact and cut the sedimentaries appear to have been controlling factors in ore deposition. No important ore bodies are exposed at the surface, and those developed wore discovered by sinking on the fissure veins to the contact zone. Most of the area overlying the favorable ore zone is covered by alluvium ranging in thickness from 5 to more than 20 feet.

Jan 1, 1950

By A. W. Khair, M. Ahmad

"Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion. oxidation, or diffusion. depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been carried out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation. INTRODUCTIONContinuous miners were introduced in the 1950’s and became the major equipment in underground coal production. Now the larger production in the coal industry has increased the demand for continuous miners and their use. It is well known that serious dust problem is also introduced with the use of continuous miners, especially with recent increase in productivity. On the other hand, legal restrictions are made ·more strict by the Mine Health & Safety Administration for the respirable dust generated by the continuous miners to prevent coal workers from incidence of pneumoconiosis. The incidence of pneumoconiosis depends on dust concentration, exposure time, and physical properties of dust. Of them, dust concentration is the best parameter for the assessment of the risk of pneumoconiosis. Although a lot of research work has been done to reduce dust concentration substantially, some areas are still required further investigation to meet the strict regulations. One of the areas is about bit wear and dust generation. In this area, the principles of bit wear and effect of bit wear on dust generation are major concerns."

Mar 1, 1992

To develop a business case that promotes adoption of noise controls by reducing barriers to industry acceptance and enhancing drivers that foster their implementation. Background Over 75% of the U.S. mining workforce is exposed to hazardous noise, putting them at risk of noise-induced hearing loss (NIHL). Consequently, coal miners suffer high rates of hearing impairment that increase to 70%-90% by retirement age. To address the noise problem for coal miners, researchers from the National Institute for Occupational Safety and Health (NIOSH) first determined that the continuous mining machine (CMM) ranked first among machines associated with reported coal noise overexposures. Further studies found that most CMM noise is generated by three component systems on the machine: dust collection, cutting, and conveying. Of these systems, the on-board chain conveyor was found to be a dominant noise source. Noise generated by the conveying system was addressed through the development of a urethane-coated flight bar chain. The coated chain, shown in Figure 1, has demonstrated an 8-hour time-weighted average (TWA) reduction of operator exposure by 3 dB(A). It has since been accepted by the Mine Safety and Health Administration (MSHA) as a "technologically achievable" noise control for CMM operators who are exposed to noise that exceeds the MSHA permissible exposure level. Having demonstrated the noise reduction performance of the coated chain, NIOSH has assembled information into a business case that can be used by operations considering adopting the chain at their worksite.

Dec 1, 2009

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

The Federal Coal Mine Health and Safety Act of 1969 has dictated major changes in mine ventilation with regard to both air quantity and quality. Requirements have also been placed on the ventilation of beltlines, gob and face areas, and air velocities on trolley haulage roads are limited. Escapeways, separate from trolley haulage roads and on an intake split of air, must be maintained continuous to the surface. These and other similar requirements have not only precipitated several modifications to existing ventilation systems but also have greatly increased the complexities of new mine ventilation planning. It is apparent that the use of computers in ventilation system analysis and design is a necessity. SUMMARY Although computer oriented analysis of mine ventilation systems was introduced over two decades ago, it has yet to receive widespread acceptance in the United States. Central to this problem is the fact that, while many computer programs for network analysis have been developed, no attention has been paid to the development of computer input data. Consequently, without this foundation, program applications have been infrequent. This thesis has directly attacked this problem and has presented all pertinent information basic to the development of good computer input data. The areas that were covered include quantity measurement, pressure measurement, fan testing, survey data balancing, and the development of a network schematic from the ventilation survey results. These discussions on data collection and the corresponding reduction to computer coding have been illustrated by an application of a ventilation simulation program to an existing mine in Southwestern Pennsylvania. The use of a ventilation

Jan 1, 1977

By Henry G. Dorsett

This report is a description of equipment and test procedures used by the Federal Bureau of Mines in laboratory studies on the explosibility of dusts. The principal tests concern ignition temperature, minimum explosive concentra¬tion, minimum electrical energy for ignition, limiting oxygen concentration, pressure, and rates of pressure rise. As new materials often present unique problems, variations in the general procedure and special tests performed are indicated, The general procedures for handling a dust sample from its receipt at the laboratory to the preparation of the report are described. The repro¬ducibility of the respective tests are shown. A brief history of laboratory studies on dust explosions by the Bureau of Mines and a description of current equipment and test procedures used are presented in this report. Its purpose is to facilitate interpretation of data previously published and those proposed to be published on the numerous mineral, agricultural and industrial dusts that have been studied. Through understanding and interpretation of the laboratory data obtained for the parameters of explosibility, preventive measures can be adopted for alleviat¬ing the hazard of dust explosions arising in manufacturing and processing industries.

Jan 1, 1960

By John A. Organiscak

[Fugitive Just is generated alone unpaved mire reads from intermittent equipment traffic. Typically, the majority of such traffic consists of trucks hauling either mine product or waste [rum the surface mime pit and/or the processing plant. Fugitive dust generated along these unpaved mine roads includes particles of all sizes which become airborne. The potential hazards include the deleterious effects to human health of inhaled dust, traffic visibility hazards and environmental impacts on the localized area by the larger-sized visible airborne dust. Two held surveys were recently conducted to quantify fugitive dust generation and dispersion from truck traffic on unpaved and untreated mine haulage roads For these surveys., airborne glow sampling was conducted at multiple sampling fixations away from an unpaved haulage road at a limestone quarry/plant and at a coal mine preparation plant lo measure the size characteristics, concentrations. and dispersive behavior of the dust cloud generated from truck traffic- Results show that at least 80% of the airborne Just generated by haul trucks was larger than 10 µm- Airborne respirable, thoracic, and total dust concentrations all decreased and approached background concentrations 30.5 in (100 feet) from the road This report describes the average and instantaneous peak dust levels that were measured tip to 30.5m (100 feet) Iron the haulage road. Keywords: Unpaved mine road, fugitive dust, silica.]

Jan 1, 2008

By Herbert R. Babitzke

As part of a project to develop refractory metal alloys suitable for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation-hardening techniques to columbium and tantalum alloys. Thirty-three alloys were evaluated to determine their formability, strength, and oxidation resistance. Three alloys had tensile strengths near 40,000 psi at 1,200° C: Cb-1N-5W-5V-10Hf (No.4), Cb-15Hf-5W-0.5B (No. 31), and Cb-15Hf-SW-IB (No. 32). Oxidation resistance of the high-strength alloys was good. Alloy4 gained only 34 mg/cm2 at 1,200° C, and 21 mg/cm2 at 1,000° C in 2 hours. Hot forming was done without any protection from oxidation.

Jan 1, 1968

By D. J. Parker

This report is based on data collected in and about the Liberty mine of the Liberty Fuel Co. by D. J. Parker and W. W. Kessler on December 13 and 14, 1933. An important phase of an examination to determine the general condition of a mine with respect to safety is the collection of dust samples from rock- dusted areas. Definite conclusions, based on intelligent interpretation of the analyses of such samples, can be reached only when the general condition of the mine is known. A similar examination and report were made on this property in January 1930 by D. J. Parker and R. I. C. Manning. Since that time much has been done by the management to improve safety conditions in this mine. The changes made will be noted in the course of this report. The mine is in Spring Canyon at Latuda, Carbon County, Utah, and is served by a branch line of the Denver & Rio Grande Western Railroad about 7 miles long and connecting to the main line near Helper, Utah. The writer desires to express his sincere appreciation for the many courtesies and helpful cooperation extended by Superintendent George Schultz and Mine Foreman F. W. Koelling.

Nov 1, 1934

By Christopher Mark

Australia and the United States both have large, modern underground coal mining industries. Many companies have invested in both countries, and there is growing awareness that technological developments in one country can rapidly affect the other. Yet the ability of technology to pass between the countries depends on comparability of ground conditions. Many Australian observers believe that their ground conditions are significantly poorer than typical U.S. conditions, but some U.S. professionals are not convinced. The author recently visited 10 Australian longwall mines and two room-and-pillar mines. Each mine visit included determination of the Coal Mine Roof Rating, roof support installed, pillar design, and an in-depth discussion of ground control experience. The Australian conditions observed are compared with an extensive data base from U.S. mines. The paper also offers observations on geotechnical data collection, monitoring, and the roles of the mine inspectorate and research community.

By C. E. Arthur

The Bureau of Mines has investigated the problem of radioactive contamination using nuclear explosives to fracture petroleum reservoirs in an attempt to stimulate production. It was concluded that some contamination of petroleum products will almost certainly occur. However) the degree of contamination cannot be predicted except by a full-scale experiment) since simulating the problem in the laboratory is economically impossible because of the extremely high temperatures and pressures that must be reached in extremely short time intervals if a reasonable analog is to result.

Jan 1, 1965