Search Documents

By Sigmund Black

Ingersoll-Rand Research, T n c and the Lee-Norse Co. built a Bureau of Mines sponsored, special deep cutting continuous miner under this contract to study the effects of rotational speed and depth of cut on airborne respirable dust. After preliminary tests indicated and later verified that deep cutting - low rotational speed reduces airborne respirable dust, a series of underground tests were performed (9 combinations of rotational speed and depth of cut at 45° bit angle and 4" bit spacing). Additional data was obtained on specific energy, coal sizing and noise. The conclusions reached from the tests results were; a) deep cutting reduces airborne respirable dust generated and specific energy needed to cut coal., b) the greater majority of the decrease occurs in going from 1" to 2" depth of cut, c) lowering rotational speed has a particularly sizable effect of reducing the amount of dust at the operator's location, d) no significant relationship was found for either noise level or coal sizing to rotational speed or depth of cut. Recommendations include. a)) use of specific energy as an indicator of the change in dust level correlating to changes in cutting parameters, b) mine operators should acquire new deep cutting machines., since retrofitting would be selective.

Jan 1, 1977

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindablity index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous of coal as delivered is a check on the practical results obtained in the coal.

Jan 1, 1967

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

By Oliver C. Ralston

The nonmetallic minerals work of the Bureau of Mines started with the organization of the Mineral Technology Division in 1912. A special experiment station devoted to the mining, preparation, and processing of nonmetallic minerals was established in 1923 at New Brunswick, N. J., and concentration problems on nonmetallic minerals of all kinds also were studied at the Mississippi Valley Experiment Station at Rolla, Mo. In July 1936 the Nonmetals Division was organized, and in May 1937 the Nonmetallic Minerals Experiment Station at New Brunswick, N. J., was moved to and made a part of the new Eastern Experiment Station at College Park, Md. At present the Nonmetals Division operates at three points: The Eastern Experiment Station, College Park, Md., which is headquarters for the division chief; the Southern Experiment Station, Tuscaloosa, Ala.; and the Northwest Experiment Station, Seattle, Wash., where coal washing and preparation studies are included with those on nonmetallic minerals. Sand, gravel, and aggregate work is carried on by the Mining Division, as sand and gravel preparation are intimately associated with mining methods. The Economics Branch of the Bureau of Mines also prepares occasional papers on nonmetallic technologic subjects in connection with the presentation of statistics on a particular industry and reviews of the mineral industry in foreign countries for use in the monthly publication, "Mineral Trade Notes."

Jan 1, 1937

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By Nils A. Eilertsen

This Bureau of Mines report describes the unit cost procedure for estimating direct development costs within a cave block in an undercut block caving mine. Costs of supervision, labor, equipment, and supplies are combined to build a unit cost for each type and size of mine development opening in the block. These costs are then combined to estimate the direct cost for developing a ton of ore. Operating data from several domestic metal mines are combined with a hypothetical mining system to illustrate the costing procedure.

Jan 1, 1975

By Richard V. Ageton, Harry E. Tufft, E. A. Holbrook

When an underground excavation is made, the rock surrounding the sides and top of the opening is deprived of its natural support and tends to fall. Whenever caving takes place, the time and extent of the caving depend on the character and condition of the rock. In strong homogenous rock, such as solid granite, even a large chamber may stand indefinitely, whereas a soft material, such as clay or a loose material like unconsolidated sand, falls immediately if not supported. Weaknesses in the rocks induced by structural features, such as joints, :fissures, bedding and cleavage planes, and fractures produced by blasting, will cause the falling of insecure blocks or slabs unless means are provided to support these in place. In an unsupported mine opening, as a tunnel, the first slight settling or adjusting movement of the rocks (the "initial creep" or "set") is caused by the great weight of overlying material pressing down the rock masses above and around the roof and sides of the opening until they key together in roughly the form of an arch. The rock, after it has adjusted itself to this shape, becomes. selfsupporting. Timbering is necessa.ry in all mining only to support, therefore, those comparatively small blocks or pieces of rock which tend to loosen from the top and sides of the opening during or after the formation 'of the natural rock arch, and which lie between this natural rock arch and the opening. This statement, of course, has its limitations. For example; a layer of strong rock, like limestone, may act as a beam; then only the material under the limestone will need support. Timbering is not, as is commonly supposed by the layman, used to supp!ort the huge mass of rock between the back (roof) of an underground opening and the surface. It would be impossible to place enough timbers in a:ny underground opening to support such a mass. This fact is not'·perceived by all miners.

Jan 1, 1923

By M. D. Aldridge

This document reports the results of a two-year research effort aimed at improving communication systems used in coal mines. This work was conducted under a program whose original goal not only involved the development of practical and effective electronic systems for operational communications, but also for monitoring, at a central location, remote instruments at key positions in a mine. About half way through the originally proposed three year effort, the program was redirected to phase out the communication effort at the end of two years and to concentrate the program" resources on the investigation of new monitoring system concepts developed by this research. Thus, the work reported here is incomplete relative to the originally pro- posed program. However, the work was carried to the point of providing sufficient evidence to aid in the comparison of certain new communication concepts. For the concepts chosen for this study, the work was stopped short of hardware development and field testing, Several reports in the form of Master's theses and a Doctoral Dissertation have resulted from this research. They each report in considerable detail the results of several individual" contributions to this program. In preparing this report, an attempt has been made to provide a complete description of the significant results but with- out burdening the reader with the minute details. These more detailed reports are referenced heavily for the convenience of those interested. PRESENT COMMUNICATION METHODS Two types of communication systems are presently used In coal mines. They are: 1, Various forms of telephone systems, and 2. Carrier current radio systems using the trolley line as the interconnection circuit. Carrier current radio is used almost exclusively for control of rail trafflc by the dispatcher. Almost all other communication uses the telephone system, Telephone lines generally extend to areas where trolley lines are not present such as the outside offices and warehouse. Therefore the telephone system provides the primary means of voice communication. Telephones - Telephone systems employed in American coal mines fall into three categories. 1. Paging type telephone systems - these systems have individual stations which use battery powered transistor audio amplifiers to boost signal levels for normal communication. When in the page mode,

By PAUL L. FISHER

This bibliography has been compiled by the Bureau in answer to many requests now being received for information on the briquetting coal and other carbons . In addition to publications issued by the Government in printed or mimeographed form, references are included to articles appearing in the technical press and in cooperative reports of work done jointly with states , colleges , and industries . References and patents are arranged in chronological order . Bureau of Mines bulletins , technical papers and Minerals Yearbooks are printed , and are obtainable from the Superintendent of Documents ,. Government Printing Office , Washington 25 , D. C. Reports of investigations , information circulars , and the directories and reports of the mineral industry surveys are published in mimeographed form and may be obtained without charge from the Publications Distribution Section , Bureau of Mines , 4800 Forbes Street , Pittsburgh 13 , Pa . Many Bureau of Mines publications , as well as bound copies of the foreign and American scientific and trade periodicals , may be consulted in technical , college , and large public libraries throughout the country. Dealers in new and second-hand books sometimes have copies of these reports for sale .

Jul 1, 1948

By O. H. Metzger

This is the first of two papers dealing with construction and use of aerial tramways in the metal-mining industry. It describes practices and equipment used in tramway construction and discusses the design of tramways. The second paper will describe the construction and operation of tramways and give operating costs. ACKNOWLEDGMENTS The author acknowledges the cooperation of a number of cable and tramway manufacturers Who supplied practical manufacturing data and other valuable information. Full credit for formulas used in the design of aerial tramways it given' to Edward B. Durham3/ and F. C. Carstarphen.4/

Jan 1, 1937

By Wiliam L. Crentz

The importance of Somerset County, Pa., as a coal producer is due in large measure to the presence reserves of low-volatile bituminous coals. Although many coal beds of minable thickness are present, the important reserves are to be found in those beds underlying the Pittsburgh bed. The Kittenning beds and Freeport beds, which are responsible for the bulk of the present coal production in Somerset County and contain the largest reserves to meet future coal requirements, are usually thin and entirely free from impurities. The Pittsburgh bed, which has been such an important coal deposit in the coal areas immediately west and south of Somerset County, is of secondary importance in this county. Although generally rather friable, Somerset County coals have enjoyed wide receptability as excellent coals and to some extent have been utilized in the metallurgical market.

Jan 1, 1951

By C. L. Karr

Researchers at the U.S. Bureau of Mines (USBM) have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by loosely modeling the search procedures of natural genetics. FLC's are rule-based systems that efficiently manipulate a problem environment by modeling the "rule-of-thumb" strategy used in human decision-making. Together, GA's and FLC's include all of the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and an adaptive element to adjust to the changes in the problem environment. The control system also employs a computer simulation of the problem environment. Details of an overall adaptive control system are discussed. A specific laboratory acid-base pH system is used to demonstrate the ideas presented; all results are from the physical laboratory system and not from a computer simulation.

Jan 1, 2010

By E. R. Maize

[?he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, cnS it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichwc :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

"The present and possible futures commercial production of potash from various sources in the United States is discussed below under the following heads:1. Potash from the saline lakes.(a),Nebraska lakes.(b),California lakes.(c),Other lakes.2. Potash as by-product from the cement kilns.3. Potash as by-product from the iron blast furnace.4. Potash from silicate rocks.(a),Feldspathic material.(b),Leucite rocks of Wyoming.(c),Sericite slates of Georgia.(d),Glauconite (greensand) of New Jersey.5. Potash from Alunite.6. Potash from organic sources other than kelp.7. Potash from kelp.In this discussion very little more than passing reference, if any, will be given to those projects which up to date have been de¬veloped only slightly, if at all, beyond the small scale laboratory stage, or for the development of which there appears to be very little financial and technical backing at the present time. Nether or not many of these proposed projects have merit can be determined only by an actual operating demonstration.Generally speaking, the potash industry of the United States has been hardly more than marking time since the armistice. This is, largely due to the fact that the consumers of potash have been expecting that heavy shipments of foreign potash to the United States would be resumed soon at somewhere near the pre-war prices, and they have not been buying domestic potash at present prices for many months. The result has been that domestic producers have been unable to sell their product at even cost and many producers of potash have been obliged to close down. Thu Nebraska lake plants were closed down in February. The California saline plants were operating at below capacity, and the only large alunite plant is closed down. Even the cement plants have little or no inducements to recover the potash being lost in their waste gases, and the production is very small at present."

Jan 1, 1919

By A. C. Johnson

The T. L. shaft of the Eureka Corp., Ltd., near Adams Hill, Eureka, Nev., was sunk in 1954 and 1955 to permit exploration and development of the lead-zinc-silver ore that had been indicated by drilling. This paper describes the sinking of the 4-compartment, vertical shaft to a depth of 1,127 feet and includes pertinent details of equipment, methods, and costs. A shaft crew of 10 men, supplemented by 13 hoistmen, topmen, carpenter, and shop crewmen, sank and timbered the 1,127 feet of shaft in 630 workdays. Total labor per foot of shaft was 107.95 man-hours. Supplies per foot of shaft included 20 pounds of explosives, 1.61 pounds of drill steel, and 200 board-feet of timber. Power consumption, including that required for pumping, averaged 3,726 kw.-hr. per foot.

Jan 1, 1958