Search Documents

By Mauro F. Dobran

The use of Slot Raises has been common for many years. The following presentation will compare various methods of developing these Slot Raises and introduce two new ones.

Jan 1, 1996

By Philip Barnhard, Lyman G. Bahr

By recording the arrival time of a pipe wall at evenly spaced intervals in a plane perpendicular to the pipe axis, application of the equations of motion permits calculation of the pressure of the explosive acting to accelerate the pipe wall. Data observed from various non-ideal explosives are presented, together with values of pressure to be expected from thermodynamic calculations.

Jan 1, 1981

By Albert G. Funk, Gary M. Thornley

The available energy of aluminized ANFO and aluminized slurry blasting agents has been measured by seismic methods, calculated theoretically, and compared. With aluminized ANFO it is concluded that aluminum concentrations should be restricted to less than 10 percent because of diminished energy yields at high aluminum concentrations. However, with aluminized slurry it is concluded that efficient use of aluminum can be made at aluminum concert"rations up to 18 percent. It is further concluded that the difference in efficiency of use of aluminum by these two classes of blasting agents results from a higher contribution to useful work from the condensed detonation products of the relatively higher density aluminized slurry blasting agent.

Jan 1, 1981

By Paul Worsey, Matthew K. Coy

New blasting mat designs are currently tested in the field on actual blasting jobs and only undergo qualitative rather than quantitative assessment. The majority of matted blasting occurs in trenching in which the blast designs and field conditions vary considerably. In order to assess a new blasting mat material and design, a new standard test was devised.

Jan 1, 2015

By Francisco Sena Leite, Vinicius Miranda

Mine blasting is directly associated with ground vibration. If these affect critical structures (buildings pit walls, etc.) they must be mitigated to reduce the environment and social impacts. Vibration monitoring and control is one of the most important procedures in blasting because it will impact short and long term incidents associated with this blast effect. Technology moves ever forward, and today we have personal devices that are equipped with an array of sensors, for that reason the authors decided to investigate the possibility of using a personal device to do vibration control. This case study compares the same blast measured with a traditional seismograph and a smartphone. To validate this new methodology, attenuation laws were built with data from a traditional seismograph and a smartphone application. Predictions were also made prior to a set of blasts. Residual analysis was used for data validation from the two different sources. From the performed analysis, to prove the validity of this new methodology, the normality tests for statistics residues analysis proves that it is possible to infer that the model has a null residual mean and a small residual error. The achieved results show the accuracy of these devices, the authors pretend to show the potential of this equipment and open a completely new door for vibration analysis.

Jan 1, 2018

By LaRay Collyer

San Juan Mine began pre-splitting the highwall prior to cast blasting in August 1986. The first pre-split shot used six inch PVC (polyvinylcloride) pipe inside a 10 5/8 inch hole, drilled at a 74 degree angle. The powder factor was about .90 pounds per cubic yard.

Jan 1, 1990

By Park Yun-Seok, Jung Seung-Won, Hwang Nam-Sun, Song Jin-hyuk, Kim Young-ho

This study proposes a new blasting vibration estimation formula that reflects the vibration reduction characteristics of electronic detonators, which are not considered in the current MOLIT blasting vibration estimation formula. Test blasts were conducted across six types of Korean open-pit blasting designs. The results of the test blasts showed that the K value for electronic detonators decreased by approximately 30% compared to electric detonators. Predicted Peak Particle Velocity (PPV) analysis indicated a reduction effect ranging from 30% to 31% across various types. By incorporating this reduction in the K value into the MOLIT blasting vibration estimation formula (K=200), a new electronic detonator blasting vibration estimation formula (K=140) was proposed. Using this new formula, the blasting damage range (R) was calculated under various vibration limits to evaluate constructability improvement. On average, the R value for electronic detonators decreased by about 17%, with significant reductions of around 41% observed for TYPE I under certain vibration limits. In conclusion, the adoption of electronic detonators in open-pit blasting operations improves blasting efficiency, reduces economic costs, and significantly enhances constructability. Electronic detonators have demonstrated superior performance in minimizing damage to safety facilities compared to traditional electric detonators, thereby proving their practicality and effectiveness in blasting operations.

Jan 21, 2025

By Geff Gordon, Dale Nies

Small diameter borehole blasting can be very efficient and cost effective. As residential development continues to expand, many areas are now requiring blasting for site preparation and upgrading old utility systems or constructing new ones.

Jan 1, 1990

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By J. -P. Tshibangu, E. Lefebvre

ABSTRACT : The Tournai’s region in Belgium is characterized by outcrops of limestone that were mined out long ago by different companies for cement and crushed materials. The region is densely populated and the vibrations generated by blasts in the quarries are of big concern. The occurrence of electronic detonators and development of computer sciences brought a new expectation in controlling the vibration level and, hence, carry out bigger blast operations. In this paper we present the results of two experimental blast programs that have been carried out by the Nobel explosive Belgium Company on the Gaurain-Ramecroix quarry to understand the effect of the delay on the vibrations generated in the neighborhood. The first program has been implemented during the early use of electronic caps in Belgium (1996) by performing some unit shots. An attempt to model the effect of the production blasts by the hybrid method (Hinzen 1988) gave promising but poor results compared to infield measurements. A new program (more than ten blasts) has been implemented in 2006 in which the delay and blast firing sequence (i.e. the order in firing adjacent holes in a row) have been changed; a new attempt is made to build unit signals by deconvolution and then try to model production ones. A comparison of the two approaches is made.

Jan 1, 2008

By Mick Fritz, Gregory Poole

Construction blasting is always challenging when in close proximity to existing structures, but when you are next to a landmark like Sanford Stadium at the University of Georgia it can get intense. Blasting on this project was performed less than 100 feet from students studying in their dorms at Reed Hall. Some shots are only a few feet from the columns on the stadium that hold up the sky boxes where meetings were being held while blasting was being performed. If a shot goes vertical the rocks would go through the floor of the sky boxes.

Jan 1, 2011

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Ashlin Pillay, Osamu Iwata

Hong Kong is ranked as the world’s third most important international financial hub and attracts significant growth and development annually. The city is also known as the world's most vertical city, the most common view from your window in Hong Kong city centre is probably the window of another 30 storey skyscraper. The increasing demand for real estate in this bustling Metropolis has placed immense pressures on its transportation infrastructure because whilst the construction continuously grows upward with larger and larger skyscrapers, it leaves the transportation planners with very little choice but to go underground. As a first world city, interrupting daily business operations is simply not an option; however, of even greater concern is the safety of these 8 million residents. Blasting Regulations are under the strict control of the Mines Division showing zero tolerance to the breaching of safety standards. The Ho Man Tin Station (HOM) excavation, a part of the Kwun Tong Line Extension (KTE) project situated in Hong Kong began in June 2012 and is one such project that is under strict regulations from the Mines Division. The HOM project is a cross cut interchange station between the Kwun Tong Line Extension (KTE) and Shatin Central Link (SCL).

Jan 1, 2015

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By C Jamie Kridler

"An increased concern for pit safety and more stringent, highwall requirements for augermining of final cuts has led to a new emphasis on wall control for a Central Pennsylvaniacoal operator. Over the course of two and one half years and several locations, fieldpersonnel developed a very practical yet very effective system for maintaining safehighwalls. This involved the use of the blast design to: l) shape the highwalls 2) create andprotect a system of benching 3) pre_split large diameter holes using suspended ANFOcharges."

Jan 1, 1993

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By Antonio S. Aldana Selders

With special designed explosive and a system to lower down a heavy load of Explosives through 8" pipe results are achieved, the stimulation of sulphur production takes place. Well # 18-1063 at 515 meters below ground is loaded with 802 units of explosives with total weight of 1820 kilos to fill up the column of 93 meters of limestone & sulphur strata.

Jan 1, 1995

By Alan Bauer

During the past several years, the trend to large-diameter blastholes in both open pits and underground mines along with the continuing developments in slurried explosives and delay systems has kept things exciting for the drilling and blasting engineer. This has been particularly so in underground mining, where new mining systems having lower cost and higher productivity have emerged. Crater technology has produced new large-scale methods for resisting front penetration in tar sand mining and also new underground retreat mining methods and methods of raising.

Jan 1, 1978

By Ankit Jha, Sudarshan Rajagopal, Purushotham Tukkaraja

Geologic structures are one of the crucial parameters in blast design. Structural geology and rock properties influence drilling patterns, blast layout, and initiation systems. A comprehensive understanding of structural characteristics is essential to achieve the desired blasting objectives. This paper aims to identify geologic features in a bench using images obtained from the drone. Images obtained from mine site are annotated for geological features such as faults and joints. Semantic segmentation of images is achieved using an encoder and decoder structure available in the machine-learning pipeline. The encoder consists of initial convolution and pooling layers to capture essential features of the geology and rock patterns from two-dimensional RGB images. Batch normalization is used to put all the features on the same scale. These images are then inputted as training data for the machine-learning algorithm. Machine learning model is trained on sub-section of interest to achieve reasonable accuracy. Initially, 1000 best annotations were used to train the model and additional samples were added later to achieve more accuracy and avoid iteration of machine learning model in wrong convergence. After the model achieves reasonable accuracy, it is used to recognize geological features on new data. Geological features identified on the new data can be used by the blasting crew in blast design and keeps the geological maps updated that can help the geotechnical team.

By B J. Kennedy, G W. Sengstock

During the last two decades, many advances have been made in open cut coal mining technology as new mines have come on stream and old mines have faced increasingly difficult mining and operational conditions. The need for close control of operating costs has necessitated consideration of modified excavation methods.

Jan 1, 1995