Search Documents

By Frank Haehnig

Ground freezing is a technique which is used more and more in tunnelling under complex ground conditions. This paper will present three case studies which highlight different aspects of the ground freezing technique when applied in urban environment. The first project is the City-Tunnel in Leipzig, Germany, which is being built beneath the central station and which is the largest ground freezing project currently under construction in Germany. The second case study is part of the North-South-Line project in Amsterdam, Netherlands where ground freezing will be carried out to al-low the TBM drive through old wooden foundation piles. The freeze tubes for this project will be driven using Horizontal Directional Drilling (HDD). The last project is the Hallandsas Tunnel Sweden where the ground freezing equipment has to be installed against high water pressure. The paper illustrates that ground freezing can be implemented in difficult ground conditions such as soft ground, highly fractured rock and high water pressure. The case studies highlight the importance of good workmanship. With the increasing numbers of large tunnels being constructed in difficult ground conditions the paper concludes that the complex case studies presented will be-come more representative for future tunnel projects in urban environments.

Jan 1, 2008

By J. W. Slatter

Cast in situ screw piling techniques (both displacement and non displacement) have seen considerable growth in recent years due to competitive production rates, low noise and vibration free installation. However the discussion on the mechanics of auger installation, which has implications on the installation effects and installation forces of screw piling augers, has been almost exclusively targeted towards non displacement techniques and in particular continuous flight augers (CFA). This paper discusses the historical development of the understanding of screw piling auger mechanics in sands and presents a new theoretical model to predict the soil transport and displacement characteristics of both displacement and non displacement augers with variable geometry.

Jan 1, 2000

By Sam X. Yao

In construction of drilled shafts under water, placing concrete in the shafts is technically demanding and involves complex construction logistics. Past construction experience has demonstrated that high quality concrete can be placed in drilled shafts under water with a proper concrete mix and proper placement techniques. However, a significant number of failures have occurred which have resulted in excessive cost overruns and delays. These problems may have occurred because proper underwater concrete construction techniques have not been widely disseminated within the industry. This is a technical area where competent design and sound construction planning can achieve a significant reduction in both risk and cost. This paper will discuss some key technical issues in the concrete mix design, concrete production and placement for the drilled shaft construction. The paper also describes two lesson-learned case histories from drilled shaft construction projects.

Jan 1, 2013

By Dan Yang

Pile foundation designs are performed routinely based on geotechnical information available at the time of design, often with due consideration of large uncertainties inherent to soils and site conditions. These uncertainties frequently are the causes of piles being installed not the same as those designed, especially by factors beyond quality assurance and quality control. With a variety of both satisfactory and unsatisfactory pile test results from these nonconforming piles, the design engineers are required to examine the foundation performance as a whole against the project design requirements before signing off on them or calling for potentially costly remediation. Over the years, as-built analysis has been a consistent way of dealing with pile non-conformity and damage in our practice, avoiding many construction delays and it is an integral part of our pile foundation design. In this paper, the key elements of an as-built analysis along with several major bridge projects are presented.

Jan 1, 2010

By Shoichi Tsukuni, Akihiko Uchida, Kazuo Konishi

"In order to investigate the effect of grid-form deep mixing walls as a countermeasure for liquefaction damage to roads and private houses in Urayasu, Japan, three dynamic centrifuge model tests were conducted. Urayasu is located in the Tokyo Bay area, and private houses in the city incurred severe damage due to liquefaction during the 2011 Tohoku earthquake. In grid-form deep mixing walls design, the distance between grid-form walls is critical to prevent liquefaction. This study clarifies the relationship between the settlement of private houses and the distance between grid-form walls under the conditions that exist in Urayasu.INTRODUCTIONMany private houses in Urayasu, Japan suffered severe damages due to liquefaction during the 2011 Tohoku earthquake (Photograph 1). Fig. 1 shows the location of Urayasu and the maximum acceleration of the observed seismic waves in the Tokyo Bay area. At Urayasu, the duration of the seismic waves (hereafter called the Urayasu Wave) was about 2 min. The maximum acceleration was 1.57 m/s2 (Fig. 2), which is relatively small. The damages occurred in the land reclamation areas that consist of loose sand with an SPT-N value less than 10.To prevent liquefaction in future, it is necessary to adopt suitable countermeasures in the areas where many private houses suffered severe damages. Grid-form deep mixing walls are one such countermeasure. Fig. 3 and Photograph 2 show grid-form deep mixing walls. Walls are constructed using the deep cement mixing method. Fig. 4 shows a plane view of planned grid-form deep mixing walls for roads and existing private houses in Urayasu."

Jan 1, 2015

By Dan Brown

Deep foundation contracting for transportation projects in the United States has typically followed the design-bid-build model in which contractors bid on a specific work product according to relatively inflexible prescriptive specifications. With continuous flight auger piling and the many types of proprietary drilled displacement auger piling, there appear to be advantages to contracting this work according to a different model. This paper provides a discussion of the use of a performance specification for this work in which the contractor has greater freedom to choose the most appropriate foundation system and also greater responsibility for the performance of the completed foundation. With public agencies subject to open bidding, this type of contractual arrangement presents opportunities to encourage innovation. There are also challenges for implementation in public works projects, notably the selection of qualified contractors and the verification of performance requirements on production foundations.

Jan 1, 2006

By Michael J. Garlich

Steel sheet piling has a long history of use in a variety of permanent and temporary structures. Current engineering practice uses numerous publications and standards for design guidance. U.S. design guidance is fragmented, with numerous inconsistencies between design guides. To improve current U.S. design practice, the North American Steel Sheet Piling Association has initiated a project to produce a design standard that will unify design procedures and provide specification guidance for engineers and users of steel sheet piling. The wide range of uses for sheet pile structures presents a challenge in developing such a standard. Load factors or allowable stresses acceptable for a temporary retaining wall in soil may reasonably vary from those for a river cofferdam or a dockwall located in sea water. However, it is still possible to provide consistent and rational guidance for such varying uses. The standard also can address sheet pile design aspects often neglected in U.S. publications, such as vertical load capacity and resistance to loads applied parallel to the sheeting.

Jan 1, 2008

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By Walter E. Vanderpool

Type 1B micropiles (Bruce and Juran, 1997) can be installed rapidly and efficiently. During an 85-day period, 536 micropiles were installed to depths of 61 meters within a site 41 meters by 43 meters. Their performance, as measured by load test, varied even where the materials, construction procedure, and installation technique were closely monitored and controlled. The variation in displacement, as measured by the standard deviation, exceeded 50 percent of the mean test-load displacement for all loads up to the maximum load applied (2670 kN). This study provides a statistical basis to predict variability with respect to the construction method, micropile materials, and installation technique. The variability of displacement at all test loads is a fundamental characteristic of this type of drilled deep foundation system.

Jan 1, 2002

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By Tony Amis, Marco Barla, Alice Di Donna

"Energy geostructures are becoming an increasingly popular solution around the world for Developers looking to reduce CO2 and system running costs. Energy geostructures are geotechnical structures that provide both the important role of structural stability while also acting as a heat exchanger with the ground, enabling the supported buildings and or infrastructure to be heated and cooled using the principle of low enthalpy geothermal systems. The main advantage of this innovative technology with respect to standard geothermal plant is the reduction of the initial installation costs and construction schedule benefits, compared to installing conventional geothermal solutions, largely due to the additional use of structures which would be constructed in any case. However, it is important with respect to energy geostructures that additional aspects need careful consideration. For this very reason, several research studies have been carried out over the last decade on this subject and a number of real case studies have been monitored and analysed. The key difference with respect to conventional shallow geothermal systems are mainly related to the geometry, which is imposed by the geotechnical project, and the need to ensure that the primary structural role is always guaranteed. Special boundary conditions, the reduced depth, the influence of atmospheric external temperature can also play an important role for energy geostructures. They can affect, both energy efficiency and, the geotechnical behaviour because of the possible thermal induced mechanical effects. This paper presents a picture of the current situation regarding energy geostructures and their peculiar features, and collects available data to provide a reference framework. Data has been collected from literature and personal communications and then processed to provide easy-to-read charts useful for practical consultation at a glance. This paper provides, an indication of the distribution of such systems worldwide, their spread in time, and a global view of their actual efficiency from the structural, energy, economic and environmental point of view.1. IntroductionEnergy geostructures are becoming an increasingly popular consideration around the world. Energy geostructures are geotechnical structures with a dual role of providing structural stability and the ability to exchange heat with the ground, to provide low carbon heat and coolth to supporting and or adjacent buildings and infrastructure, using the principle of low enthalpy geothermal systems (Barla and Di Donna, 2016; Laloui and Di Donna, 2013). A closed circuit of high density polyethylene (HDPE) pipes is embedded in the concrete, and a heat carrier fluid circulates through them exchanging heat with the ground. The HDPE pipework circuit inside the geostructure is linked to one of the above buildings or infrastructure through a heat pump, which adapts the temperature of the circulating fluid to the heating (winter mode) and cooling (summer mode) needs. In this way, heat can be injected into the ground during summer and extracted from it during winter. In principle, all structures in contact with the ground can be used as energy geostructures. The first examples of energy geostructures date back to the eighties in Austria and were mainly piles and shallow foundations. A decade later, Henderson et al. (1999) reported on what would appear to be the first successful use of geothermal energy piles in the US, with loops incorporated into the foundation for a hotel in Geneva, New York. As was their use in this New York case history, the typical geothermal energy pile application is used in conjunction with additional closed loop boreholes to provide the required energy capacity for a structure. Interestingly the report concludes that the geothermal energy piles had a better heat transfer performance than the borehole field. The first energy walls appeared slightly later, while still today only a few experimental cas"

Jan 1, 2017

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By Andreu J. Ferrero

Polyurethane and acrylate resins are routinely injected into soils to gain strength and control water flow. However, most published data regarding strength gain is derived from laboratory samples created under ideal conditions. This study endeavored to inject resins into full scale mock-ups that could then be excavated and tested to yield results comparable to actual field conditions. To achieve this goal, a large container was filled with a silty SAND (SM), as defined by the Unified Soil Classification System (USCS). The soil was moisture treated and compacted in lifts of 0.3m. PVC pipes installed in a diamond grid into the soil were used to inject polyurethane and acrylate resins. Dynamic cone penetrometer (DCP) tests were conducted on the polyurethane treated soils, the acrylate treated soils, and the baseline untreated soils in the container. Testing results will be correlated to SPTn and CBR values to evaluate increases in the soil strength parameters in the treated soils. Cored samples of polyurethane and acrylate treated soils will be tested in compression, shear, and triaxial. These laboratory test results will focus on material property gains for the treated soils, in comparison to standard values for similar soil types. Complete documentation of the soil type, compaction methods, injection methods, and testing performed have been documented and will be presented in the final paper.

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By Jeff Starchuck, Harald Kullmann

"In 2005, an inspection showed that the Deception Bay Wharf in the Canadian Arctic was at the end of its service life. Although Deception Bay is closed with landfast ice up to 5 ft thick, shipping operations continue year-round, with additional voyages in the summer open-water season to supplement mine supplies. The rehabilitation scheme that allowed minimal interruptions to shipping involved concrete caissons cast on barges and an ingenious placing system.WorleyParsons Westmar of Vancouver, B.C., performed the inspection under contract to the owner, Xstrata Nickel, Montreal, Quebec. The wharf, on the coast of the Nunavik region of Quebec, was originally constructed in 1971 for an asbestos mine, and is now used to support Xstrata’s Raglan nickel mine, importing fuel for p o w e r g e n e r a t i o n a n d general mine supplies, and exporting nickel concentrate to smelters in the south. Emergency repairs were essential to allow operations to continue at the site, while the parties considered permanent rehabilitation options and secured funding. The repairs were done in the openwater seasons, and included reinforcing the failed interlocks above water level with steel patch plates and injection grouting of the cell fill below the port crane in 2005. In 2006, workers installed a circumferential belting system below water level.Westmar held critical planning sessions with the mine operation personnel to find ways to stretch the limits of the mine supplies and nickel storage facilities. In the end, the parties agreed to shut down construction activities four times during the ice-free season to allow access to the dock site.Westmar developed a plan that allowed mine operations to continue during construction, and Xstrata approved the plan and budget in September 2006, for execution in 2007. Rapid construction was essential. To accommodate the short construction season and maintain minimum levels of service for the mine, the work was radically different from conventional Arctic deep-sea port construction. Like the original Deception Bay Wharf, construction practice was to use steel sheet pile circular cells with the consequential heavy support services for the labour force. Construction duration was typically two seasons. The plan for Deception Bay was executable in one season based on a concrete caisson structure. Only a modest amount of schedule float was needed."

Jan 1, 2009

By D. X. Xu

A pump station was constructed at the food of a steep mountain, very close to a riverside. To protect the pump station from being washed out, and to guarantee the stability of the steep hillside behind the pump station and the safety of the foundation pit when the station was built, cast-in-place R.C. diaphragm walls (Fig. 1) were clesigned in front of and on both sides of the pump station. This wall was 130m long, 0.8m wide and 29m deep. The diaphragm walling on both sides of the pump station served to prevent landslides and to fix anchor piles. The 55m long diaphragm walling in front of the pump station served as a temporary shuttering which kept earth and prevented water from permeating when the pump station was under construction. After the pump station project was finished, static blasting method was used to blow up the wall body which was 10m beneath the ground so that the water from the river could come into the pump station. The remaining wall body below this level was kept to prevent soil from being washed out. [ ]

Jan 1, 2010

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008