Search Documents

By W. Baranek

The paper describes activities undertaken for intensification of copper cathodes production in electro-refining plants of the Polish copper smelters: 'Legnica', `Glogów I' and `Glogów II'. In the 'Legnica' smelter, Outokumpu?Wenmec machine was used for preparation of copper anodes. Intensive studies were conducted in order to optimise copper electro-refining conditions. As the result of them, spacing between the electrodes was reduced to 99 mm, which enabled placing forty-one cathodes in each tank and increasing amperage from 10.8 to 13.0 kA. This modification resulted in the increase of electro-refining capacity to 103,000 tons/y. Intensification of the copper production at `Glogów II' by 18,000 tons/y became possible after development of new electro-refining procedures, including application of a regime of changes in electrolyte level during the cathode cycle, implementation of the changes in location of starting sheets relative to anodes, and in dimensions of the sheets, and modification in the shape of the anodes. Similar works have been performed at `Glogów I', which were concentrated mainly on defining of a new method of anodes preparation, modification of their geometry, determination of optimum current density, composition of a set of inhibitors and of a method of their introducing. The implemented solutions resulted in the increase in electro-refining capacity at `Glogów I' from 207,000 to 240,000 tons/y.

Jan 1, 2007

By M. A. Upham

"Prairie Evaporites of the Province of Saskatchewan in a deep oil-well hole. Exploitation started in 1950 under a shroud of doubt that this huge reserve could be mined. It was fraught with almost insurmountable physical problems in penetrating the Prairie Evaporites. After 12 years of experimentation and development of new shaft-sinking methods, mining equipment and processes to treat the high-grade potash ore (sylvanite), a new era of high-risk resource development dawned in Saskatchewan.The development of 10 new mines opened up the largest known mineable potash reserves in the world and Canada became the second largest. producer of potash to supply domestic (U.S.A. and Canada) and overseas markets. A monumental program in marketing-devising new transportation systems and strategically locating warehouses-was developed in order to expeditiously service domestic and overseas customers. The year 1969/70 started a period of overcapacity and the problem of prorationing. As the market strengthened in 1974, the Saskatchewan Government applied the reserve tax to the industry. Then, they announced the setting up of a Crown corporation to acquire ownership by purchase of up to fifty per cent of the industry. During this time, potash was discovered in New Brunswick within 50 to 60 miles of a seaport, where two deposits have been explored by the same pioneers who started the potash development in Saskatchewan.With this background, the paper will examine various elements of the economics and marketing of Canadian potash."

Jan 1, 1980

By A. McIntyre, L. R. Plitt

Both the Bond and the Hardgrove grindability tests are widely used in the mineral industry to measure the ease of the comminution displayed by a material. The Hardgrove test is mainly used for coals, whereas the Bond grindabifity test is mainly applied to hardrock minerals. The Bond grindability has the advantage that it can be empirically related to the energy required for comminution (work index), whereas the Hardgrove grindabifity test has the advantage of being easier to perform. In an effort to establish a valid correlation between work index and Hardgrove grindability, a series of parallel grindability tests were carried out on a wide variety of rocks and minerals. The standard Hardgrove test was modified to allow for materials with a higher density than coal. A new, satisfactory relationship was established which permits rapid estimation of work index from Hardgrove test data.

Jan 1, 1980

By K. Kim

"All milling operations would like to achieve the best possible recovery in combination with the highest achievable throughput. Unfortunately, many operations have problems with low recovery, low throughput or both. In the majority of these cases investigated by the author, the solutions to improve recovery and throughput were simple. The solutions did not include implementation of new technology or major capital, but rather a return to fundamentals. In most cases, problems occurred because the operation was not following their own operating procedures, because the design of the circuit was changed without adequate change management or understanding of the implications of changes, or because basic metallurgical measurements and control were not taken or ignored. In this paper, examples of these problems and their solutions derived from long and varied experience will be discussed. The objective of this presentation is to provide the milling operator with practical and readily implementable solutions to common milling issues to improve throughput and recovery.INTRODUCTION Mill operations can be evaluated by many operating parameters, but the two best indicators are recovery and throughput. These two parameters summarize the wellbeing of an operation. The grade to the mill is also a good indicator, but this is usually controlled by the mine. The best recovery and throughput are achieved through a team work involving operators, maintenance workers and metallurgical staff. The milling operations include many unit operations, such as crushing, grinding, flotation, leaching, carbon in leach, Merrill Crowe, roaster, autoclave and refinery. The tools available to the operations are plant design, process measurements, assays, metallurgical balance, and operating strategy. Twelve real life examples of improvements of recovery and throughput are presented in this paper. EXAMPLE 1: CRUSHING CIRCUIT WITHOUT FINE ORE BIN At this operation plant throughput could not be maintained at a high rate because feed to the mill became coarse during the day. The cone crusher was feeding the ball mill directly. As the day wore on, the gap on the cone crusher would slowly increase, which would cause the product size to increase. This would increase the re-circulating load on the ball mill. The throughput would decrease accordingly. Furthermore, the throughput would decrease more with high frequency of maintenance on the cone crusher."

Jan 1, 2019

By Stéphane Chevrel

Non-energy raw materials are vital inputs for the EU?s economy and maintaining fair and undistorted access to these materials for EU industry and citizens is increasingly difficult. Within the EU, exploration and extraction have to face increased competition for different land uses and a highly regulated environment. While the EU is currently dependent on the importation of many metals, the overall potential for mining and quarrying in Europe is strong. In spite of this, the land area available for extraction in the EU is constantly decreasing, turning access to land into a key challenge for the extractive industry. The EOMINERS project aims at contributing to demonstrate how to improve the EU capacity in implementing new mining sites and their societal and environmental acceptability. The overall aim of EO-MINERS (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation) is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry and the society in view of its sustainable development while improving its societal acceptability. EO offers a unique opportunity to collect necessary spatial parameters that play a key role for better assessments of mining-related environmental and societal impacts. It could enable the development of means to identify the site-specific environmental and societal footprints of mineral resource extraction and to determine their respective significance. This understanding of global and cumulative footprints along a causal chain is needed in order to target policy measures. In this way the expected reduction of environmental and societal footprints in the mining sector can be most effective for the environment and more cost-efficient for public authorities and commercial operators. The project first defined environmental, socio-economic, societal, and sustainable development indicators and criteria that can possibly be dealt with using EO techniques. After an analysis of policies related to the environmental and social footprint of mineral industries, project expertise and stakeholder interviews (national and on-site) as well as site investigations led to the establishment of a list of indicators to be monitored, either directly or indirectly, through accessible parameters. Development of EO-based monitoring tools is then carried out over three demonstration sites: the lignite open pit of Sokolov in Czech Republic, the Mpumalanga coalfield centred on the town of Emalahleni (previously Witbank) in South Africa, and the Makmal gold mine in Kyrgyzstan. From these developments, it is subsequently intended to contribute to the development of generic, standardised EO data integration schemes, in particular in view of characterising affected ecosystems, populations, and societies and prepare indisputable documents that will make the basis for a sound ?trialogue? between industry, governmental organisations, and stakeholders. This paper discusses results obtained after three years into the project, focusing on product development over the demonstration sites and their relevance to the observation and monitoring of environmental and societal footprints of the extractive industry.

Aug 1, 2013

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By F. J. Macias, A. Bruland, F. E. Dahl

"Tunnelling by use of Tunnel Boring Machine (TBM) is gaining a greater presence as a suitable excavation method. Disc cutter consumption has a strong influence on performance and cost when using TBMs and the influence becomes even more relevant in hard rock. Furthermore, good predictions of TBM performance and cost facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory assessments are needed. A new abrasivity test method called Rolling Indentation Abrasion Test was developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than traditionally used methods by introducing wear by rolling contact on intact rock samples. INTRODUCTIONHigh investments are involved in the tunnelling industry, especially in Tunnel Boring Machines (TBMs) projects. Performance predictions and cost estimations are crucial for planning and risk management of TBM projects. Cutter consumption has a large influence in terms of time and cost, and an even greater effect in case of hard rock projects. Many factors are influencing the amount of cutters consumed in hard rock TBMs. Normal TBM operation results mainly in abrasive wear on the cutters and appropriate methods for abrasivity assessment are needed. Rock abrasiveness cannot be considered as an intrinsic property and the complete tribological system should be considered in addition to the geological properties of the rock.In the present paper, a new test method for abrasivity assessment in tunnel boring called Rolling Indentation Abrasion Test (RIAT) is presented. The traditionally used test methods for determination of rock abrasiveness uses sliding or impact contact in order to cause wear while the RIAT introduces rolling contact on intact rock samples. The ambition of the new test device is to have a reliable method to evaluate the cutter wear in hard rock tunnel boring by reproducing wear behaviour on rolling disc cutters in a more realistic way. It has been established by many authors that the abrasion of a cutter ring is proportional to its rolling distance (Rostami, 1997; Bruland, 1998). In the present work, the weight loss of a mini-cutter ring is measured subsequent to testing in order to evaluate wear in the rolling process and could hence be related to cutter ring wear. Indentation of the tools in the intact rock sample is considered as an indication of the surface hardness of the rock or the resistance to indentation by rolling."

Jan 1, 2015

By H. A. Kee

In the mining industry, as in other business, one of the more satisfactory results of sincere but cheerful effort lies in the proper completion of undertakings and problems, which, to be successful, must continually hold the interest of all concerned in the work. In most undertakings, genuine interest and satisfaction is largely dependent on the proper appraisal of opportunities presented, and the opportunity to associate ourselves with sinking operations at McIntyre central shaft, from the surface to a depth of 4,133 feet, was genuinely appreciated. This opportunity was made possible by the previous persistent and successful leadership of Mr. J. P. Bickell, President, with the assistance of his associates, and of the general manager, Mr. R.J. Ennis, in the development of the McIntyre Porcupine mine, and I beg to state that any success in this sinking operation was very largely due to the congenial co-operation and splendid workmanship of Captain Martin C. Horne, his shift bosses, leaders, and all those who worked with us . Our slogan throughout was " Safety First for Pleasant and Efficient Workmanship," and this general policy made it possible to sink and timber 2.,123 feet during the first year without a serious accident.

Jan 1, 1928

By J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

"Ni-based superalloys have been replaced in the last low pressure stage of jet turbines for aircraft by titanium aluminides. In order to improve the properties of these Ti-Al alloys and extend their usage deeper into aircraft engines grain refinement by inoculation has been investigated. Borides are the most common inoculants for Ti-Al alloys, however they form brittle particles which are detrimental to the final properties of the alloy. Inoculants manufactured from a Ti-Al alloy with refractory metal additions were proposed to alleviate the issues arising from inoculation with brittle particles. An alloy was chosen which had less than 10% lattice mismatch with the alloy of interest (Ti-46Al) to maximize efficiency. Initial experimentation showed a decrease in as-cast grain size by a factor of 2 between the inoculated and non-inoculated samples along with an absence of the brittle particles found with boron inoculations. Investigations into the interaction between the inoculants and the melt were also carried out to better understand the inoculant size distribution and efficiency upon solidification.INTRODUCTIONTitanium aluminum alloys are an interesting material for aerospace applications. Their high temperature oxidation resistance and high specific strength make them particularly promising (Kim & Dimiduk, 1991). Recently, titanium aluminides have replaced nickel based superalloys in the last low pressure stage of the GEnx turbine engine. In order to increase their usefulness in turbines their properties must be improved for high temperature (>800oC) applications. Grain refinement is one method to improve the properties of a material, however current methods of grain refinement of Ti-Al alloys by inoculation have significant drawbacks. A new method of inoculating Ti-Al alloys by using Ti-Al alloys with small refractory metal additions (Nb, Ta) has been developed to avoid the drawbacks of current methods while still being effective grain refiners."

Jan 1, 2016

By Hyumng Sup Choi

The role of the interfacial electrical 'Condition on the adsorption of col-lectors on mineral surfaces has been studied by electrophoretic mobility and adsorption measurements made on zircon. From the investigation of the electrokinetic properties of zircon, H+ and OH-are seen to act as potential determining ions, thus controlling the electrical nature of this mineral. The isoelectric point of zircon occurs at a pH of approximately 5.0, and it is evident, therefore, that the zircon surface would be positively charged below a pH of 5.0 and negatively charged above this pH. The adsorption of collectors therefore de-pends strongly on the pH of the solution; anionic collectors are adsorbed on positively charged surfaces and cationic collectors on negatively charged surfaces. This, in turn, de-fines the effective flotation condition, with respective collectors, for this mineral. The above results have been correlated with the flotation behaviour obtained by the simplified flotation test using a modified Hallimond tube.

Jan 1, 1963

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By William H. White

"AbstractThe value of anomalous metal contents of trees as an aid to the discovery of mineral deposits was tested under field conditions cm four known ore deposits. Results indicate that a base-metal deposit, or any deposit containing zinc or copper, casts a 'metal shadow' into the overlying soil which remains approximately positioned above the deposit, regardless of the type of overburden or the movement of groundwater.The unusually high content of zinc or copper in trees growing within the limits of this 'metal shadow' constitutes an anomaly which can be detected and ,plotted in the field The field kit and certain points of the field technique are described briefly; and the characteristics of plant anomalies and possible limitations of their use are mentioned.IntroductionRecent investigations concerning the metal content of trees indicate not only wide variations in the metal content of different species and in different parts of the same tree but, in addition, suggest that the metal content of a tree is related to that of the subjacent bed-rock. Abnormal values found by Warren, Delavault, and others in trees growing above or near orebodies suggest a new tool which may prove of considerable value in exploration work. Evaluation of this new tool must involve consideration of the following questions:(I) Is the technique one which can be used under field conditions by persons not specially trained; and can results be duplicated within reasonable limits of error? Rather than taking tree samples for subsequent laboratory analysis, it is highly desirable that analyses be made on the spot. This allows anomalous results to be checked and additional samples may be taken at key points."

Jan 1, 1950

By Jo Render

Expectations of your management approach ??Life of mine applicability ??Tailor scale of activity to scale of project ??Assess impacts, risks, and opportunities ??Use global good practice, backed up by rigorous analysis ??Support with trained monitoring and evaluation team ??Information infrastructure to allow ongoing trend analysis and tracking of progress ??Public reporting using standardized indicators Yes, we are talking about a ?management system?

May 1, 2011

By Mauro Chiesa

A. New Dictionary, Since 2007/8 Traditional concept of ?cycle? is dead A dearth of projects AND good metal prices suggests otherwise In a depletion-business, good times for any greenfields in 2-3 yrs! ?Balance? sheet means quality assets = quality capital So, de-risk the assets, and ration the capital ?Replacement costs > historical costs ?Discounted assets depleting; replacement costs need self-financing (FCF) ?Public-sector slows permits, avoids assets and wants more of FCF ?Capital ?markets? are now ?market fragments? ..and? ??Shareholder? has changed from ?growth? to ?income + performance? ?Higher search costs, higher capital costs and higher cost of capital

May 1, 2013

By George A. Guess

The making of contracts for the purchase of ores is a business which the metallurgist usually understands better than the miner. Companies in the custom ore business often employ an ore buyer who is aware of the class of ore which the smelter needs, and is thoroughly conversant with the business. The miner on the other hand makes ore contracts but seldom, and it is often only after a settlement has been made that he realizes the meaning of the terms of the contract under which he has sold his ores. He has expectations usually greatly in excess of the amount 'net proceeds' shown at the bottom of the settlement sheet. Seldom does the occasional shipper really know his contract. A somewhat similar parallel is to be found in insurance policies. We all have insurance policies; we never know the conditions contained in them until after the fire. The clauses in the policy are for the protection of the Insurance Company. An Insurance Company has no friends.

Jan 1, 1926