Search Documents

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By Jérôme Girard, Shiu Kam, Sue Longo

"Historically, tailings management in a northern climate has involved the deposition of tailings into the Tailings Management Area (TMA) as conventional slurry. This type of system is obviously viable but presents challenges that are difficult to manage as circumstances change over the life of mine. These issues can include:? Increases in mill throughput, and? Life of the TMA for the life of mine.This case study will present how thickened, high-density, non-segregating tailings are used as an alternative to conventional slurry disposal to achieve greater storage capacity and enhanced environmental performance for a gold tailings facility in a northern climate. This paper will focus on how this change in deposition strategy accommodated the increased throughput of the mill and the increased life of mine. Specifically, the paper will discuss the addition and integration of new processes to the exiting mill system to accommodate the tailings management issues. It will highlight the challenges from laboratory testing to pre-feasibility to the engineered design of the thickened tailings system implemented at Musselwhite Mine.BACKGROUNDGoldcorp Canada’s Musselwhite Mine, in Northwestern Ontario (120 km north of Pickle Lake), is an underground gold mining operation that began production in 1997. The current mill throughput is about 4000 tpd (1.4 Mtpa). Gold extraction is based on a CIP process with cyanide destruction.The existing tailings management area (TMA) is located about 2 km southwest of the mill complex. The TMA is contained by high ground to the north and to the west and flanged by a moraine ridge along the south side. A number of dams have been constructed along this ridge. The dams were first built in 1996 and subsequently raised in 2000 and again in 2005. Excess tailings pond water is discharged to a polishing pond then released to the environment via a wetland.The TMA was originally designed to contain 13.7 Mt of tailings under a ponded surface for closure. The water cover was to inhibit adverse long-term environmental effects because the tailings contain pyrrhotite and other sulphide-bearing minerals that are potentially acid generating. The design was modified during Stage 3 Construction in 2005 to expand the storage capacity to 17.3 Mt (Golder, 2005). As of end of 2009, over 16 Mt of tailings had been deposited in the TMA. The slurried tailings were historically deposited at 50% solids."

Jan 1, 2011

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By R Thomson

The use of uranium metal in non-ferrous metallurgical practice is dis-cussed with reference to its alloying behaviour and chemical activity. It is suggested that the more promising applications are in the treatment of molten metals to combine with impurities. Mines Branch work along these lines is described for copper, zinc, magnesium, aluminum and nickel alloys. It is shown that a cop-per-uranium master alloy (25 per cent U) successfully deoxidizes molten copper without detriment to the electrical or mechanical properties of the product at residual uranium levels of up to 0.8 wt. per cent. Additions of uranium to alpha brass in amounts greater than the lead impurity content were found to remove the deleterious effect of lead on hot-workability. Similar deoxidizing and malleableizing effects were found with uranium additions to nickel. It is thought that uranium forms stable intermetallic compounds with many impurity elements. A significant malleableizing effect can therefore be expected in the presence of other elements besides lead.

Jan 1, 1963

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By Scott Martin

This paper will discuss the challenges currently facing the mining industry. By sharing experiences gained in the CIM Leading in Mining Course, I will highlight what’s working, what’s not, what are the challenges, what are the concerns, what are the opportunities, what needs to happen. Specifically, I will discuss what is currently happening with leadership and leadership development in members’ own organizations, what skill sets are important to develop in different hierarchical groups and how comprehensive leadership courses like the leading in Mining course can help improve leadership within individuals and the industry. Leadership development is a process not an event.

Jan 1, 2014

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion&apos; as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as &apos;worn out&apos;. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

By M. Maccagni, J. Nielsen

"Engitec developed the EZINEX® Technology some years ago to recover zinc from oxidized secondary sources. This process works at neutral pH and can take into solution any kind of metal, but iron is rejected and remains in the leach residue. Engitec has also developed the FLUOBORATE System, which is able to recover lead and copper from relevant concentrates. Some iron is leached into solution, but it is controlled through a solution purification bleed treatment. In this paper, we present the two above mentioned technologies. They are very different with regards to the chemical environments and the methods used to control the build-up of iron in solution, but both systems are suitable to treat iron bearing feeds.INTRODUCTIONIn the design of hydrometallurgical processes, the most important issues are the water balance, the filtration and the control of impurities. This is particularly important when the process includes an electrowinning unit. Iron has been one of the most problematic elements to remove, especially in acidic environments.Engitec Technologies has developed several hydrometallurgical processes divided in two different electrolyte lines: the Fluoborate Technology for the recovery of lead and copper from primary and secondary sources and the Ammonium Chloride System based on a chloride electrolyte for the recovery of different non-ferrous metals, among which zinc and lead are the most important. In both cases, iron is present in the feed and needs to be eliminated from the solution. It is not a problem for the quality of the metal produced, but when present in solution, it consumes the basic electrolyte reducing its free concentration which is very important both for both the leaching and electrowinning unit operations. Both process systems are very peculiar, the fluoborate case being much more intriguing."

Jan 1, 2016

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By D. J. McLaws

"Recent innovations in metal smelting technology utilize continuous oxygen-enriched smelting and converting processes which are capable of producing off-gases containing up to 60% SO2 or more. Other SO2 recovery processes, involving solvent absorption and steam or vacuum regeneration, can produce off-gases with SO2 concentrations nearing 100%.Processing of these high-concentration SO2 off-gases in conventional sulfuric acid plants can cause excessively high catalyst bed temperatures and poor SO2 conversion. In order to avoid these problems, a conventional acid plant design must dilute these high SO2 process gasses with dilution air in order to provide the required oxygen to effectively convert the SO2 and provide a heat sink (via the inert N2) such that the exothermic reaction, SO2 + ½ O2 ???SO3, does not exceed the temperature limit of the catalyst or the converter vessel.MECS, Inc. (MECS) has proven that a high SO2 feed gas design can be a viable option which can increase energy recovery, reduce energy consumption and potentially reduce capital costs."

Jan 1, 2014

By Vincent Roy

Numerous on going activities at the Daniel-Johnson Dam : ? Surveillance / monitoring ; ? Structural investigations & evaluation ; ? Injection work ; ? Crack mapping ; ? Instrumentation management (drawings & inventory) ; ? Drainage system state ; ? Foundation evaluation

Aug 1, 2013

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

Over the last three decades, the mining industry has been moving towards more underground mechanized mining methods and the number of LHD vehicles utilised has increased. The growth of mechanization and automation has benefited both workers and the mining companies. However, due to the design of the LHD vehicle and the limitations of the operating environment, restrictions to operator visibility are inevitable. The inability of the equipment operator to see clearly (i.e. people, objects or hazards) around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines, visibility assessments for existing machines are traditionally completed in the field using a light filament technique. Past researchers have used the light filament technique to collect obscuration zones around the equipment and to produce a 2D chart of this information. The 2D shadow diagrams have proved to be useful in highlighting potential equipment problems and have been performed repeatedly to show the potential of redesigning a part of the LHD for improving visibility. The light filament method involves manually collecting data and requires a level of judgment to be used. As a result the method is susceptible to errors and requires around three hours to complete. The objective of the current research is twofold; firstly to develop a rapid method for field visibility data collection using a laser scanner and secondly to compare results of repeat tests for both light filament and laser scanning methods. A MENSI GS100 laser scanner along with Pointscape and 3Dipsos software has been used to collect visibility information and process the data. The research aims to develop the laser scanner as a technique to rapidly evaluate the visibility profile of an LHD vehicle. Machine design changes can then be assessed quickly using these results.

May 1, 2004