Search Documents

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By H. Scott Swinden

"ForewordA symposium on base metal deposits was held in Bathurst, New Brunswick, from June 10-13, 1990, sponsored jointly by the Geological Surveys Branch of the New Brunswick Department of Natural Resources and Energy, the New Brunswick Prospectors and Developers Association, and the Geology Division of the Canadian Institute of Mining, Metallurgy and Petroleum . Papers prepared for the symposuim are being published as a series of articles in the CIM Bulletin. This second paper (the first was by Fyffe, et al., in Vol. 83, No. 938) in the series presents an overview of the paleotectonic settings of massive sulphide deposits in the Dunnage Zone of Newfoundland with emphasis on volcanic geochemistry.ABSTRACTCambrian and Ordovician volcanic sequences of central Newfoundland, which record the history of the Iapetus Ocean, are prolific hosts to volcanogenic massive sulphide (VMS) deposits. Geochemical, isotopic and geochronological studies show that the vestiges of Iapetus in Newfoundland probably record a complex series of island arcs and back-arc basins that were marginal to, rather than part of, the main ocean basin of Iapetus. The geochemical and isotopic data provide a means of characterizing the tectonic environment of individual volcanic sequences, and allow us to identify a number of distinct tectonic environments in which VMS depositiontook place.Four tectonic environments have been identified as being associated with VMS deposition: (I) back-arc environments hosting VMS deposits include both N-MORB-type ophiolites (e.g. Skidder?) and volcanic sequences with oceanic island (or within plate) tholeiite characteristics (e.g. Great Burnt Lake); (2) primitive arc environments include both supra-subduction zone (SSZ) ophiolites (e.g. Betts Cove, Rambler) and volcanic/epiclastic sequences (e.g. Point Leamington, Duck Pond) and are characterized by abundant arc tholeiites, with lesser refractory lavas and rhyolites; (3) mature arc environments comprise dominantly thick felsic and mafic volcanic piles in the Buchans - Robert's Arm Belt (including the Buchans camp) and are characterized by dominantly calc alkalic basalt and andesite; and (4) continental rift environments occur in the Hermitage Flexure area (e.g. Strickland deposit) and are characterized by dominantly felsic volcanic sequences.Island arc environments are by far the most prolific hosts to VMS deposits. Patterns of VMS distribution in central Newfoundland show that similar tectonic settings may be recorded by very different stratigraphic sequences (e.g. both ophiolites and thick volcanic/ epiclastic sequences may record primitive arc rifting) and emphasize the importance of the rifting in VMS generation, irrespective of the details of the tectonic or stratigraphic setting. The ability to judge the prospectiveness of a volcanic sequence by using whole rock geochemistry to evaluate its tectonic environment may prove useful in area selection at the grassroots exploration level."

Jan 1, 1991

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

By J K. Irwin

The authors discuss the application of drum and friction hoists under modern conditions and give four examples of friction hoists proposed for various applications. The paper concludes with a summary of the advantages and limitations of friction hoists relative to drum hoists. Introduction T H~ introduction of the multiple-rope friction hoist m the late 1940's has complicated the se-lection of the right hoist for a given job. Once such considerations as rope safety factor, drum to rope ratio, hoisting distance, tons per hour and/or service duty have been decided upon, the selection of a drum hoist is relatively simple. We now ask our-selves "which hoist -drum or friction? (See Figure 1 and Figure 2). When a friction hoist is a possibility we are immediately concerned with how many ropes to use, whether to hoist balanced or counter-balanced, whether a friction hoist will be flexible enough for the application and, of course, what the relative costs will be.

Jan 1, 1964

"Accelerated expansion of Western Canada's metallurgical coal industry has again stimulated considerable exploration activity in the Rocky Mountain Foothills Belt and influenced much of the R&D related to transportation, processing and carbonization. Preparation R&D has included further pilot-plant work on desulphurization, spherical agglomeration and modified compound cyclones (which are also proving themselves in other mineral beneficiation studies). Combustion research, aside from increasingly stressing control of combustion source pollution, has directed special attention to lignite PF firing and problems arising from lignite ash. Studies directed toward the non-fuel utilization of coal have centered on such diverse topics as active carbons, carbonaceous filter media, plant nutrients and industrial applications of humic acid derivatives. In addition, a number of long-range research projects related to such matters as coal chemistry and pyrolysis have been actively pursued, and further attention has been given to improved sampling techniques and analytical methods."

Jan 1, 1969

By Edgar Stanfield

Since April, 1923, the Scientific & Industrial Research Council of Alberta has had an analyst, Mr. W. P. Campbell, steadily employed analyzing coal samples taken by the provincial Mine Inspectors. Mr. Campbell has also analyzed a number of coal samples taken by one of the Council's Geological Survey parties. We have thus, at the time of writing, over four hundred analyses of Alberta coal, made by the same analyst, and strictly comparable. These samples come from widely distributed points, some 88 townships being represented. The stream of samples is still flowing in, and it is hoped by the end of this year that the number of townships represented will be increased at least fifty percent. The time has arrived to publish some of the data collected; but it must be clearly understood that this is merely a progress report, subject to revision as further information is obtained. Three hundred and fifty-three coal mines in the province were operated during 1923. The production per mine varied from 5 up to 500,000 tons. With this number of mines to examine (and fresh mines are being opened every year) it is a large task to make even a proximate analysis of representative samples from every mine. Any chemist will appreciate the fact that to make ultimate analyses representative of even the larger mines will be a long and tedious task. It has seemed better to make a comprehensive survey by proximate analysis and determination of calorific value before beginning the more thorough survey by ultimate analysis. This paper, therefore, deals only with proximate analyses and calorific values; and, owing to limitations of time and space, does not deal with other chemical and physical characteristics of coal, such as storage quality and fusibility of ash, important though these are.

Jan 1, 1925

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By W. E. Oching, M. M. Ghomshei

Attracting and retaining workers in mining industry has become an uphill battle to many mining companies. As workers with significant experience retire, it is getting more difficult to attract not only new workers but also top talent to the mining industry to replace professionals exiting the workforce. To make matters worse, students’ enrolment in the post-secondary mining programs in Canada and USA is continuously declining year after year for reasons not directly linked to job market. This raises a question of how can the future needs of mining be met? This paper focuses on avenues for collaboration of industry and educational institutions to meet the current and future needs of mining. It provides effective approaches that mining institutes can engage with program advisory committees, role of the mining industry in supporting both faculty and students, how to harness the benefits of diverse workforce in the country and use of innovative technologies to attract young workers in mining. This work presents Human Resources (HR) professionals with tools that they can use to hire and retain skilled workers with strong interest to work in the mining industry. It also provides HR professionals with an opportunity to re-evaluate their restructuring practices during economic downturns as they reduce number of employees on temporary or permanent basis. The paper stresses the need of working together of the mining stakeholders including mining industry, academic institutions, First Nations’ communities and provincial(state) and federal governments to meet the current and future demands of mining as the industry experiences shortage of labour and low students’ enrolment in post-secondary mining programs. It is shown that mining educational institutes can enhance their programs and recruitments through establishing a better communication with all stakeholders. This communication can be facilitated by creating a national advisory board, to work with all mining programs at the national level for sustainable mining.

Jan 1, 2023

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By M. O. Makwarela, M. W. Erwee, K. Bisaka

"Energy efficiency in mining and minerals processing forms part of Mintek’s long-term research strategy which includes a specific programme designed at overcoming the challenges faced by the South African pyrometallurgy industry.The electric smelting industry is currently severely constrained by the global economic downturn as well as by the availability and increasing cost of electricity. Efficient utilisation of electricity through energy recovery systems and improved smelting process flowsheets can significantly contribute towards creating sustainable operations.Apart from efficient engineering design and solid process control, smelting of either cold or hot pre-reduced ores has been shown to decrease furnace electricity consumption by more than 40%. Various methods of solid-state reduction tests have been carried out at Mintek in order to select the most appropriate process option in the context of the South African industry. This paper summarises a subset of the results obtained, specifically on pre-reduction tests done on South African chromite and manganese ore pellets.In this set of tests, it was found that the use of an organic binder, together with B2O3 as flux, promotes manganese ore pre-reduction, but retards the pre-reduction of chromite. By pre-reducing the manganese ore feed, significant cost savings can be achieved in subsequent smelting processes and there is potential to minimise manganese losses as a result of fuming, due to possible lower operating temperatures."

Jan 1, 2016

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By Kristopher John Shelswell

The work in this paper describes the theory, development and analysis of a computer model simulating a mine operation moving material using concurrent decline ramp truck haulage and skipping practices. This simulation was designed specifically to assess the performance of the truck haulage component and to expand on the scope and capabilities of traditional TKM fleet calculations. Haulage fleet simulation results were similar to TKM calculations for the lower to moderate production rate cases. However, comparisons of ramp-up and high production rate scenarios indicated that the simulation model was significantly more sensitive to operating practices and factors not accounted for by calculations derived when using a single TKM figure. Given the proper calibration of inputs and logic, the simulation model was additionally capable of providing information associated with general mine operations efficiency. Further benefits of the simulation model over a TKM approach included logistical assessments such as production schedule feasibility, productivity trade-off quantifications for proposed operating practices, and the validation of mine resource utilization scheduling. The simulation model was able to expand on traditional methods to approach planning and logistics by considering factors such as truck queuing, real-time traffic interactions, random events, and competition for resources on mine productivity.

May 1, 2013

By Taisuke Sakakibara, Shinya Suzuki, Tatsuya Kato, Chiharu Tokoro, Kenichi Muto

Surface complexation using a diffuse layer model were constructed for arsenic (As(V)), zinc (Zn(II)) and silicate (Si(IV)) for aluminum hydroxide in the co-precipitation process. From experimental investigations using isotherms, zeta potential measurement and XRD analysis, it was confirmed that co-precipitation involved not only surface complexation but also surface precipitation. However, surface complexation was major mechanism for As(V), Zn(II) and Si(IV) removal under the target removal level of the Japanese effluent standard. In surface complexation modeling, exchange capacity of aluminum hydroxide was determined from specific surface area obtained from experimental measurement and site density obtained from reference. Surface complexation coefficients were determined by fitting the removal property and sorption isotherm obtained from co-precipitation experiments. These parameters were in agreement with the numerical parameters found by Karamalidis and Dzombak (2010) who reported a database of adsorption equilibrium constants for gibbsite. The surface complexation models constructed in this study were applied to neutralization process of an actual AMD treatment. Our model could successfully represent the pH edges for As(V), Zn(II) and Si(IV) in the neutralization of AMD.

Jan 1, 2015

By C. A. Jeffrey, K. Pearson

Abstract - The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the overlying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release of volatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of lowtemperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehnite and pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, during post-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystalline calcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from fluid inclusion work indicates that two fluids were involved in the deposition of the zeolite veins. One fluid was initially of relatively high temperature (~100°C to 320°C) and low salinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other was of relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.), and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat flow, initiating the circulation of hydrothermal fluids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Jurassic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By C. A. Jeffrey, K. Pearson

The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the over-lying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release ofvolatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of low-temperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehniteand pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, duringpost-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystallinecalcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from ?uid inclusion work indicates that two ?uids were involved in the deposition of the zeolite veins. One ?uid was initially of relatively high temperature (~100°C to 320°C) and lowsalinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other wasof relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.),and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat ?ow, initiating the circulation of hydrothermal ?uids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Juras-sic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

By T. Fliß

The protection of natural resources is of essential importance in times of rapidly increasing populations and resulting shortage of agricultural land. Soil and groundwater resources play a central role for the production of food or feed of any kind. The intensive agricultural and environmentally friendly use of these resources must ensure sufficient income and sustainability of life for future generations. Mining projects often represent a particularly deep intervention into ecosystems due to their size as well as the most expensive treatment processes. Conventional mines comprising of shafts and developed mining fields require the stockpiling of waste rock and in particular to potash mining, the discharge of brines from raw salt processing. In contrast, mining operations based on the solution mining method can be operated without major environmental impacts and lower security risks. While the solution mining for the production of rock salt finds application since more than 500 years, exist a procedure to produce potash using solution mining only since the 1980's. For solution mining drill holes are used to exploit the potash, launched from the surface into the deposit. The exploitation of the raw material occurs by the dissolution of the potash injecting solvents and creating so-called brine caverns. Currently, a number of mining projects in Carnallite deposits by the solution mining method are in progress around the world. Often these projects are located in sensitive ecosystems. K-UTEC project and support actual a solution mining operation of a Carnallite deposit for a Chinese customer in South-East Asia. This work comprises a comprehensive geological and geomechanical modeling as well as stability analyses. Furthermore the cavern design and brine field layout as well as the planning of the brine processing and the plant design. The present paper introduces this project as a case study. The application of a special solution mining procedure and processing design ensures an emission-free mining operation (Zero Disposal Plant). The emission-free operation is achieved by utilizing the full extent of the caverns to dispose the liquid solutions from processing. The presentation of principal salt processing and technical equipment will be rounded by information about the geology of the deposit. Since the deposit includes a number of sensitive minerals, such as Tachyhydrite and Bischofite the presentation comprise a lot of interesting items with special view at the brine field operation. K-UTEC designed and delivered a special blanket measuring system and a well cement according the request of the customer. K-UTEC, a research and engineering company with more than 60 years of experience in the sector of potash and rock salt mining, developed the world's first solution mining operation for Carnallite in Germany more than 30 years ago. In recent times K-UTEC served in different solution mining projects worldwide, with special view at the environmental impact, as well as the optimal utilization of the deposits.

Aug 1, 2013

By Tony Szwilski

Using Unity 3D as a collaborative multi-user virtual on-line environment, an interactive virtual underground mine platform (IVUMP) is being developed to provide on-line access to mine safety preparedness training with a focus on mine emergency response exercises (MEREs). Communication and information flow among MERE participants and their actions can be monitored, recorded and evaluated. A mine ventilation simulation utility VFIRE is being incorporated to enhance the realism and interactive nature of the ?in-world? exercises as well as extend its functionality to include training in real-time ventilation and fire control.

Aug 1, 2013