Search Documents

By H. Tan

The effect of carbonaceous matter on gold extraction was investigated in cyanide systems with pure gold as well as pre-robbing sulfide gold ores. Auger studies demonstrated that the carbonaceous matter preferentially smeared on iron sulfide rather than aluminosilicate surfaces during wet or dry grinding. During mechanically mixed leaching, coating of sulfides and silicates and stripping of carbonaceous matter occurred simultaneously. TEM and XPS studies indicated preferential coating in the form of elemental (graphitic) carbon at the edges and the defect sites of particles. Interestingly, carbonaceous matter extracted from the gold ore was predominantly graphite and not preg-robbing in a solution with a high KCN concentration. However, the carbonaceous coating had a significantly detrimental effect on gold dissolution when gold was pre-ground with the gold ore. Artificial coating on gold surfaces with the natural carbonaceous matter from the ore was also found to substantially retard gold dissolution. With the addition of the natural carbonaceous matter from the gold ore, gold extraction from two non preg-robbing sulfide gold ores was inhibited owing to carbonaceous coating. The presence of carbonaceous matter significantly reduced the current density for gold oxidation and increased the current density for pyrite oxidation. This could explain the fact that carbonaceous coating hindered gold dissolution while enhanced sulfide preg-robbing.

Jan 1, 2005

By A. M. Ramadan

The composition of phosphate rocks, mainly used in manufacturing fertilizers, varies among deposits; therefore, phosphate rocks from different sources are expected to behave differently in acidulation processes. This paper examines the effect of preconcentration of phosphate ore from El-Sebaiya East, Egypt, using flotation on uranium leaching. A high-grade ore sample (27.3% P2O5, 168 mg/kg U) supplied by the Al-Nasr Mining Company, was subjected to reverse single-stage flotation to separate carbonate from the phosphate sample. Subsequently, P2O5 and U concentrations were 32.2% (92.1% recovery) and 225 mg/kg, respectively. After the leach process, the U concentration in the liquor was 319 mg/L.

Jan 1, 2014

By B. Fang

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment, The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate, The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By Warren A. Sheaffer

THE chief uses for copper are as a conductor of electricity and as the chief component in brasses and bronzes. For such uses, the copper must be of very high purity. H the impurities are zinc, iron, lead, arsenic, or antimony, they can be removed to a great extent by fire-refining. H, however, gold, silver, nickel, or cobalt are present, electrolytic refining is necessary. Electrolytic refining must be preceded by fire-refining and hence all impure copper must be fire-refined. The electrolytic refining of copper is most efficiently carried on when the impurities in the anodes are at a minimum. Some of the impurities tend to deposit with the copper at the cathode, while others remain in solution, decreasing the conductivity of the electrolyte and thus increasing the voltage necessary for refining. Since these dissolved impurities must be removed by continuous purifications, the amount of impurity in the anode copper should be reduced by furnace refining to some predetermined limit. Anode furnace operation aims to reduce these impurities to a minimum beyond which the cost of further furnace refining would exceed that of removing the remaining small amounts of impurities from the electrolyte. The anodes should have a fine-grain internal structure because any pieces of metal becoming detached from the anode during the electrolytic refining are inconvenient to remove from the cells and may cause short-circuits. Impurities tend to disrupt such a structure and thus form zones of weakness during corrosion. When the impurities are reduced to a satisfactory mini-mum, the anode, due to having a fine-grain structure, will corrode uniformly over the entire surface area exposed to the electrolyte. Oxides of the impurities may be volatile, in which case they pass off as flue gases, or they may form viscous slags having a lower specific gravity than molten copper, thus permitting their removal by skimming. Some impurities can be oxidized by introducing air into the bath. Due to the large solubility of oxygen in molten copper, oxygen is distributed uniformly throughout the bath and thus comes into intimate contact with all impurities. The oxides which are insoluble in molten. copper are removed either as flue gases or as slag.

Jan 1, 1942

By J. F. J. Thomas

"AbstractBoth the quantity and quality of waters available as raw materials are important to Canadian industry and to the national economy. The huge demands of many Canadian industries is illustrated by tabulated figures, based on the 1950 Canadian production of certain products, and on United States figures for the gallons of water required to produce a unit quantity of each product. It is suggested from comparison with American survey results and figures that Canadian industrial water consumption is 1 to 11/2 billion Imperial gallons per day. Since present information on Canadian usage is meagre and it is not certain that American survey results can be directly applied to Canadian industry, this estimate must await confirmation in future studies.The hydrologic cycle and the principal factors affecting the quantity and quality of water, namely, climate and season, topography, geology, vegetation, and human activities, are discussed and the principal salts dissolved in water which affect industrial use are enumerated.The present survey studies by the Mines Branch on water quality are outlined. Besides chemical analyses of municipal water supplies within a watershed, periodic sampling and analyses of major surface waters for a one-year period is being carried out. The importance of studies on seasonal variation in quality is stressed by comparing the dissolved salts in various river waters with river flow. Figures showing such relationships in the Rideau river and Ottawa river at Ottawa, the Columbia river at Trail, B.C., and the Battle river at Unwin, Sask., are presented. Different rivers show different quality changes with changing flow, and possibly only after long-term studies can the relationships be predicted.Quality studies on water may be as important as studies on many other raw materials. The quantity of the raw material, water, is not inexhaustible nor is the quality indestructible, and more realization of its importance, followed by conservation and intelligent use, is desirable."

Jan 1, 1952

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By Paul Bedard, Réal Daigneault, Guy Perrault

"La mine Lamaque est située a Val d'Or, Québec; les roches hônes appartiennent au groupe de Malartic, partie supérieure, et sont des andésites et des pyroclastites. On y retrouve deux formes d'intrusifs; des petites cheminées (ca. 150 m D) et des dykes (ca. 10 m d'epaisseur). Les petit es cheminées contiennent:1 - des diorites et des tonalites (cheminées principale, est et ouest) d'affinité calco-alcaline: Zr 140 ppm, Sr 761 ppm, P2O5 0.31% et (La/Sm)n 3.0;2 - des diorites (cheminée 4) d'affinités tholéiitique: Zr 32 ppm, Sr 181 ppm, P2O5 0.27% et (La/SM)n 1.5.La diorite de la cheminée no 5 contient deux fractions, une de chacune de ces deux affinités. Les dykes tant de porphyre feldspathique quartzifére que ceux de prophyre feldspathique sont d'affinité calco-alcaline: Zr 83 ppm, Sr 500 ppm et P2O5j 0.10%.Le gisement de 10 mine 2 est filonien: veines subhorizontales (""flats "") surtout et veines sub-verticales dans des zones de cisaillement. Le dernier réajustement structural de direction de compression nord-sud a broyé le quartz des veines existant es et rendu possible leur minéralisation. Les veines minéralisées contiennent du quartz, de la tourmaline, de la calcite avec des traces de scheelite, de pyrite et d'or; elles sont bordées par de minces (2 à 20 cm) bordures d'altération où l'on retrouve un enrichissement en carbonate, paragonite, apatite, rutile, saphène et zircon et où les phases ferromagnésiennes sont disparues. On a documenté le migrations géochimiques suivantes:I - de la bordure d'altération vers l'éponte, K2O, Rb et MgO;2 - de l'éponte vers la bordure d'altération, Na2O;3 - de l'éponte vers la veine, SiO2.P2O5, TiO2, Zr, Y, Nb et CaO sont enrichis dans la bordure d'altération."

Jan 1, 1983

By Kri Inwood

"IntroductionIn 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nov a Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the first great war, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today.The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:""The most rapid growth of the Canadian iron and steel industry has occured since 1897... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable ... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores""Donald also argues that metallurgical progress had been necessary to render the ores valuable,""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions.""The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel -making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1983

By J. Fournier, D. Fortin, F. Robichaud

Since milling began in 1988, the Laronde mill has been expanded several times, the most recent, increasing the milling rate from 5 000 to 7 000 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails in order to cope with high silver/gold ratio associated with the discovery of the Penna shaft. Since the commissioning of the Merrill-Crowe refinery in 2000, several modification and expansion projects were performed to reduce health and safety hazards. Remarkably, several of these improvements have contributed at increasing productivity and Net Smelter Return of the refinery while reducing worker's injuries. In 2004, the refinery was audited to evaluate and quantify the circuit performance. Metallurgical and mechanical operating conditions of the refinery are now understood and areas for further improvements are well defined. This paper describes some of the factors that have contributed to this improvement and describes how ergonomics and recovery can further be improved.

Jan 1, 2005

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By Gordon A. Irons, H. Y. Hwang

An impinging gas jet on a water surface was studied to understand momentum transfer in oxygen steelmaking. Depth, width and oscillation frequency of the jet cavity were measured and the splashes interpreted with Kelvin-Helmholtz instability and combined Rayleigh-Taylor and Kelvin-Helmholtz instability theory. A model to calculate separate gas and liquid velocities, applying the exact momentum boundary condition, is proposed.

Jan 1, 2004

By G. W. Neumann, J. R. Schnarr

The lead-zinc-copper-silver ores mined by Brunswick Mining and Smelting Corporation Limited at their No. 12 underground mine and No. 6 open-pit operation, and treated by distinct concentration processes in separate plants, present difficult metallurgical problems because of the extremely fine dissemination of the valuable minerals with pyrite and pyrrhotite. The problem of concentration is further complicated, in the No. 12 ore, by the presence of a varying content of graphitic carbon. This paper describes the milling of No. 12 ore and the production of copper, lead and zinc concentrates by differential flotation.

Jan 1, 1971

By E. Hardwick, K. C. Sole, Y. Jurrius

"The Luilu cobalt plant at Kolwezi, Democratic Republic of Congo, has been operating since the late 1950s, using a conventional precipitation flowsheet for removal of impurities from the cobalt process stream. Most impurities are, however, incompletely removed using this technology. Copper and zinc, both of which quantitatively deposit at the cathode in the cobalt electrowinning process, are two of the main impurities contaminating the cobalt metal product. Ion exchange offers a modern approach to removing these impurities from the cobalt advance electrolyte.Following a laboratory testwork programme to identify a suitable ion-exchange system, an on-site pilot-plant trial, treating 1500 to 3000 L/d of electrolyte, was operated for a period of six weeks to optimise the operating conditions and to determine full-scale design criteria. Copper removal was carried out using a fixed-bed lead-polish configuration with the Lanxess iminodiacetic acid resin, TP 207. Zinc removal was subsequently carried out in a similar configuration using the Lanxess aminophosphonic acid resin, TP 260. The optimised system proved capable of removing both copper and zinc from 20 to 30 mg/L to <1 mg/L from plant electrolyte containing ~20 g/L Co. Selective elution allows co-loaded cobalt to be returned to the main circuit and value to be obtained for the copper impurity. The process shows operational and economic advantages over the traditional flowsheet. Full-scale implementation of the developed process is in progress and some design considerations are discussed."

Jan 1, 2014

By Michael Samis

The real option valuation method is often presented as an alternative to the conventional discounted cash flow (DCF) approach because it is able to recognize additional project value due to the presence of management flexibility. However, these two valuation methods can be separated on a more fundamental level by their differences in risk discounting. Real option valuation applies the risk-adjustment to the source of uncertainty in the cash flow while the DCF method adjusts for risk at the aggregate level of net cash flow. This seemingly small difference is the reason why the real option method is able to differentiate between projects according to each project?s unique risk characteristics while the conventional DCF approach cannot. This paper provides an overview of the real options and DCF valuation frameworks and discusses the differences in risk discounting that exist between the two methods. Using grade-school mathematics, this paper clearly demonstrates how, with real options, a unique project risk discount can be calculated which is directly linked to the project?s unique risk profile. It also highlights why the DCF method fails in this regard and shows why a call to ?increase the Risk-Adjusted Discount Rate? is an incomplete solution at best. Finally, a heap-leach project and satellite reserve development project are valued with both techniques and the difference in investment conclusions is explained in terms of the risk-discounting concepts discussed here.

May 1, 2003

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation&apos;s business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938

By L. E. Djingheuzian

IN 1953, Lewis (1) published an article which brought forth a great amount of discussion by grinding engineers. In his contribution to discussion the present writer (2) suggested that, for the most efficient performance of a ball mill, there must be a .definite relationship between Cn, per cent critical speed, and V p, per cent mill volume occupied by the ball charge. Later, he ( 3) was able to publish some grinding data from Wright-Hargreaves milly which appeared to bear out this contention. It is with this view to establishing a fundamental relationship between Cn and Vp that the idea of this Forum was conceived. Accordingly, a questionnaire was prepared and copies of it were mailed to over eighty Canadian mill operators. This questionnaire did not include a question on dilution on the assumption that each mill operator was using the most efficient dilution for his operation, nor was a question on efficiency of classification included since it was thought that the inclusion of efficiency of dassification in the questionnaire at this preliminary stage might render the forum discussion,. while everybody was trying to find his bearings, too unwieldy. However, it is evident that, as discussions develop, this forum will have to define a uniform method for establishing most efficient classification in grinding circuits

Jan 1, 1957

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005