Search Documents

By J. W. Reynolds

Introduction The Sullivan mine, at Kimberley, B.C., is the principal source of ore for the Consolidated Mining and Smelting Company of Canada, Limited. Current production amounts to about 2,500,000 tons of lead-zinc ore a year. With approximately 1,600,000 feet of percussion drilling and 700,000 feet of diamond drilling being carried on each year, any improvements in drilling practice are important. Testing of new equipment and drill bits is a major function of the Testing Department at the mine. Tungsten carbide bits have been the subject of many tests since 1947 and have been used in operations since 1948. This paper details with the methods of testing and gives comparative data on performance and costs for tungsten carbide bits as compared to steel bits. Operational use of tungsten carbide bits started in April, 1948, and the extent of application has increased considerably since that time. The scale of employment is illustrated in Table I, which also shows other statistics on the use of carbide bits. Up to the present time eighteen types of carbide bits or tipped steel, as made by six different manufacturers, have been tested. In general, one supplier's bits have been used in operations, but some large-scale operational tests have been carried out with other types. The types tried are shown in Table II. To date they have been, the subject of 33 tests, covering the destruction of 804 bits over an observed footage of 42,586 feet.

Jan 1, 1951

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By S. L. Chen

The Kumera Technology Center developed a unique type of steam dryer for drying copper concentrate in the mid 1990s. The dryer has been chosen in several copper smelter projects since 1999. To expand production capacities, the Norddeutsche Affinerie smelter, the Pirdop smelter of Cumerio, the Toyo smelter of Sumitomo Metal Mining and the Tamano smelter of Hibi Kyodo Smelting have carried out projects in which Kumera Steam Dryers were installed. The capacity of a single steam dryer varies from 70 t/h to 160 t/h. This article summarizes the latest operation results of the Kumera Steam Dryers in these smelters and introduces the progress of the ongoing projects in Yanggu Xiangguang Copper, Guixi smelter of Jiangxi Copper, Jinlong Copper, Boliden Harjavalta, and Onsan smelter of LS-Nikko Copper.

Jan 1, 2007

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By R. B. Hyde

"Severe drilling conditions and difficult mud problems are briefly out-lined as the major cost items in all production operations. The chief problems discussed are abnormal pressures, high temperature, trouble-some shales, and low rates of penetration. These problems have been eliminated or greatly reduced in many areas by• the proper application of recently developed drilling mud products and techniques. These severe problems and their solutions are discussed generally: the application of high-density weighting materials to overcome abnormal pressures; surfactant muds with sodium polyacrylate as a solution for deep and high-temperature drilling; shale control muds and new dispersants for severe shale problems; and low-solids emulsions and •extreme-pressure lubricants for greatly improved rates of penetration."

Jan 1, 1959

By R. E. Johnson

Seventy years after the start of the Industrial Revolution in Great Britain, as reckoned from Arkwright's water frame patented in 1769, there was a significant development of the metallurgical industry in Virginia. In Britain, crucible steel had been rediscovered by Benjamin Huntsman in 17~0, and this made spring and tool steel more generally available. The metal-turning, screw-cutting lathe, including the basic principles recognized in today's engine lathe, was developed by Henry Maudslay about 1797. Wrought iron, as manufactured by Henry Cort's process patented in 1784, was readily available. Richard Trevithick's highpressure steam locomotive had met its test on the Pennydarren tramroad in 1804, and George Stephenson had built his famous Rocket, along with several other locomotives, at Newcastle around 1828. Puddling furnaces and a rolling mill had been placed in operation at the Tredegar Iron Works in Glyn Sirhowy, Monmouthshire, Wales, in 1807. In the United States, expanding commerce and a growing population resulted in continuing development from the Chesapeake to Virginia's Blue Ridge, and this demanded improved means of transportation. Ore deposits rich in hematite had been found in Virginia's Piedmont during the Colonial period, and a number of blast furnaces now dotted that area. The products of these operations were mostly pots, kettles, stove parts and like items for local trade. The James River and Kanawha Canal was incorporated in January 1785. Its eastern leg, winding along the slope of the high bluffs overlooking the river, was completed about 1800. About two dozen railroads were chartered in Virginia between 1830 and 1837. With expanding population and steady industrial development came a need for metallurgical products. Throughout the eastern United States, numerous metallurgical enterprises sprang up, and many of these flourished. The purpose of this article is to outline the development of one Southern metallurgical company, the Tredegar Iron Works, which was to have a significant impact on the industrial development of Virginia and the fighting of the American Civil War. Although the Tredegar Iron Works no longer exists, remnants of the early operations have been restored, and the current status of the site is also presented.

Jan 1, 1999

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By S. W. Marcuson

In the late 1960's concerns about the natural environment reached high levels within North America and provided activists with suitable platforms for exerting influence over the general public and politicians. In response a host of regulatory mechanisms were developed, statutes, voluntary measures, land grants, codes of practices etc. Emerging environmental awareness from the era provided impetus for rapid technological change that encompassed all industries, especially the base metal business. The resulting clean up impacted all aspects of copper production, dealing with issues such as waste disposal, water and air quality with specific impact on emissions of sulfur dioxide and particulate. This paper provides a perspective of these changes reviewing the macro-economic impact of environmental movement in mining with its specific implications to the copper smelting industry. The fundamental challenges that were faced by the old, but capital-intensive North American plants and the approaches taken to deal with the changing times are reviewed with special emphasis on the conceptual approach to smelter S02 abatement and different paths taken in the USA and Canada. The role of economics, sustainable R&D and presence of technical infrastructure that facilitated the change process is elucidated, and speculations are made about the future state of pyrometallurgy and the natural environment. Cu2007 -

Jan 1, 2007

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By Stopford Brunton

For many years it has been accepted as axiomatic that the greater number of &apos;veins&apos; or &apos;leads&apos; in the gold districts of Nova Scotia are of the &apos;interbedded&apos; type. The corollary to this hypothesis is that the vein or lead will have a continuous hanging-wall of one kind of rock, and a continuous footwall of the same or another kind of rock; but the essential point is that the foot and hanging walls are, according to this theory, both continuous and of uniform composition throughout; and that the vein or lead conforms to the bedding of the adjacent strata. With regard to the deposition of the gold in the rocks, the probability is that the key of the problem is contained in a statement by E. R. Faribault, of the Geological Survey of Canada: "The combined effect of cleavage, jointing, and stratification is to cause the rocks, especially the quartzites, to break into rhombohedral blocks". It is essential to comprehend that the rocks of the Province are no doubt folded into anticlines and synclines; but also it must be fully realized that the gold deposits and pay-shoots do not depend so much upon these as upon the fractures resulting from the disturbance caused by the intrusion of granite masses, and controlled by the combined effect of cleavage, jointing, and stratification. These fractures would form the channels through which the ore-bearing vapours and solutions would rise, and at the junctions of these fractures, where the fracturing was greatest, the easiest passages would be afforded to the ore carriers, with the result that the ore-shoots would be found at or near the intersections of fractures. It is a significant fact that in at least thirteen different districts throughout the Province, operators have at various times remarked upon the occurrence of rich ore at the intersection of &apos;leads,&apos; &apos;veins,&apos; &apos;beds,&apos; etc.

Jan 1, 1928

By W. H. MacLean, P. J. MacGeehan, A. J. Bonenfant

"The Norita deposit is an Archean volcanogenic-exhalative Fe-Zn- Cu sulphide accumulation of the distal type, consisting of six overlapping stratiform massive sulphide lenses, interbedded with exhalative cherts and thin pillow basalt flows, which formed down-topographic-slope from a mineralized hydrothermal discharge zone in the Norita rhyolite. The sulphide lenses are of two main types: channel-fill deposits such as the Main Zone and Main Zone West, composed of intricately layered pyrite-sphalerite-chert, which formed by the dynamic down-slope transport and re-deposition of sulphide exhaled from the vent zone; and stratiform lenses such as the Cu-rich A-Zone and A-Zone West, which formed even farther down-slope, in basinal depressions flanking the dome. Although rotated into a vertical position by folding, the sulphide lenses are otherwise essentially undeformed and contain a wide range of preserved primary sedimentary structures.Of prime importance in exploration has been the recognition that the formation of the distal sulphide lenses was controlled by submarine paleotopography, and that it is possible to approximate the sea-floor paleotopography using variations in the thickness and strike extent of the interbedded volcanic rocks. This has proved to be a major and successful exploration tool in the search for further sulphide mineralization in the mine, and offers prospects for use elsewhere in the district."

Jan 1, 1981

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By G. M. Hughes, R. W. Dunn

"AbstractCurrently installed an analogue instrumentation devices at Sherritt 's Ruttan Concentrator control. and/ or measure mill tonnages, grind, pH, density , some reagent and slurry flows, and cell levels. On-stream analysis is used to assay the main process streams. The history of development of process control is reviewed from startup to the present stage of selection of a process control computer. A pragmatic approach has been taken to process control to ensure compatibility with the needs and resources of Ruttan. Emphasis is made of the need to have the mill performing well from a mechanical and instrumentation point of view and to have opera tor acceptance of the computer through training. Plans for the computer phase to achieve these objectives are outlined.IntroductionTHE COPPER-ZINC OREBODY at Ruttan Lake was discovered by Sherritt exploration personnel in 1969 and by mid-1973 a 10,000-tpd mine and concentrator were in operation. After a typical startup period , the major mechanical problems in the crusher and concentrator have been resolved. Metallurgical performance is now up to standards forecast in the feasibility study.The cost of the original instrumentation installations, including an on- stream analyzer, was about one million dollars or 4% of the cost of the milling complex. Although there was no intention of using a process control computer until the plant was operating smoothly, it was understood that all instrumentation was compatible with .a computer, but this did not prove to be correct. This paper cover s the development of the instrumentation loops to date and the control strategies that will eventually be implemented through a process control computer."

Jan 1, 1977

By E. A. Brown

"IntroductionBACK IN THE nineteen-thirties, when Eldorado was a private company and was preparing to become Canada's first radium producer, the Mines Branch in Ottawa did much work on the development of chemical processes for the Port Hope refinery (1).In 1945, after the Canadian Government had taken over Eldorado for •atomic energy reasons, the Mines Branch was called upon again, this time to help out by looking into ways and means of improving ore treatment methods for the mine at Great Bear Lake. A group of technical men was assembled to devote full attention to this work, which was known as the Eldorado Project.Three years later, in 1948, the Government decided to reopen the development and operation of uranium properties to private enterprise.Since it is a function of the Mines Branch to assisit private development of Canadian mineral resources, this new uranium policy made it important for the Branch to be in a position where it could provide up-to-date services, technical assistance, and information relating to treatment of radioactive ores, mineralogy of radioactive ores, and assay methods for radioactive ores.At the same time, .because of the demand for increased uranium production, lower grade ores had definitely come into the picture, ores that might be of decidedly lower grade than, say, Eldorado pitchblende, and of entirely different nature."

Jan 1, 1953

By Robert A. Creaser, David R. Lentz

Abstract - The Moss molybdenite deposit, which was mined during both world wars, is hosted in late Grenvillian granitic pegmatite dikes. These dikes are locally aplitic, and intrude the late tectonic Onslow syenite (probably correlative with the ~1090-1070 Ma Kensington suite), which is in turn intrusive into the 1170-1155 Ma Chevreuil intrusive suite of southwestern Quebec. A Re-Os model age of 1053 ± 4 Ma (8.3 ppm Re) was obtained for molybdenite from a pegmatitic veinlet within an aplitic phase of the dike. A much younger Re-Os date of 860.9 ± 9.2 Ma (6.9 ppm Re) obtained previously from a pyrrhotiteand pyrite-rich metasomatic vein might reflect Os diffusion during slow cooling of the Grenville province, because this age is consistent with K-Ar dates reported from the region. Alternatively, the similarity between these younger dates may be fortuitous, and may instead relate to sampling issues for molybdenite. The Mo-rich granitic dikes at the Moss deposit are similar to other Mo-rich A-type pegmatite-aplite granitic dike systems that formed immediately after the peak of the Ottawan orogeny (1070-1090 Ma), and possibly are more closely related to the Kensington suite than previously thought.

Jan 1, 2005

By R. E. Gilmore

PREAMBLE THIS PAPER comprises material presented in two separate &apos;Papers at the British Commonwealth Scientific Specialist Conference on Fuel Research held in London, England, in July, 1950. These papers are now available for publication in Canada, since only essential parts of the conference discussions, in addition to the resolutions resulting therefrom, will be published in the official Proceedings of the Conference. Inasmuch as the information presented concerns Canadian organizations and training facilities for fuel research, it should be of general interest to Canadian scientists, and especially to the Coal Division of the Canadian Institute of Mining and Metallurgy. Part I, the alternate title of which is Facilities in Canada for Fuel Research and for Exchange of Information and Staff, does not include research on peat, oil shale, petroleum oils in general, and natural gas, and omits studies of the geology, constitution, and production of coal. Special reference is, however, made to research on the heavy crude oils and bitumen of the Western Prairie Provinces, and particularly to their production and treatment to produce crudes for oil refinery processing.

Jan 1, 1951

By N. T. Avard

THE profitable disposal and utilization of much of our slack coal, lignite, and other low-grade fuels is one of the major problems facing the coal mining industry of Canada today. It is my belief that the pulverization process applied to these fuels opens the door to greater efficiency and greater prosperity, and I wish to discuss briefly with you some features of its development and advantages to date. Indeed, the art of burning pulverized coal under stationary boilers is one of the romances of modern engineering. As a Nova Scotian, I feel some pride in the fact that at Chignecto Mines, N.S., was built in 1906 the first pit-mouth power plant on the North American continent. This was built to make effective for the first time Edison&apos;s dream of carrying coal for power by wire rather than by rail. This plant, built by the Maritime Coal, Railway and Power Company, Limited, success-fully utilized underfeed stokers for twenty years but in 1927 was replaced by a more modern plant equipped with machinery for burning pulverized coal, which is now operating very successfully. A further source of pride is the fact that the first boilers on this continent to be operated by pulverized coal were installed by the Dominion Coal Company at New Waterford, N.S., in 1912 and were satisfactorily operated during the lifetime of the plant. It is an acknowledged fact that average living conditions on a large part of the North American continent are far superior to those of any other people on earth. The reason is that we use so much more machinery per capita, and cheap power supply has been a large factor in bringing that about. Statistics show that where one horse-power was used one hundred years ago to assist man in his work, five hundred horse-power is used today. Truly a remarkable development and the key to our present high standard of living. Lack of coal in the chief industrial centres of Canada has forced the extra-ordinary development of the water powers which Providence has placed in those centres. How many of us realize that Canada stands second in the world in the per capita development of hydro power, Switzerland being first and the United States sixth? From this condition, we are reminded of the fact that the per capita foreign trade of Canada far exceeds that of our great neighbour to the South-but another illustration of the benefits accruing from our great power development.

Jan 1, 1937

By R. T. Jones

"Technical publications in the field of mining and metallurgy have existed for a long time. Recent developments in electronic publishing on websites make it possible to disseminate information more widely and cost effectively than before. Professional societies have an opportunity to serve their members and their industry by publishing high-quality peer-reviewed papers on their websites as well as in printed form. Older publications can be scanned, and optical character recognition can be used to provide searchable text. Various business models exist around this process. This paper outlines the approach used by the Southern African Institute of Mining and Metallurgy (SAIMM) to provide free open access to their journal papers and conference proceedings, as well as the work being done by OneMine.org to collect technical papers from a number of international societies and make them available to subscribers via a large database. An approach is outlined that should be of benefit to authors, readers, and society at large.INTRODUCTIONGeorgius Agricola (1494-1555) was not the first writer on the subjects of mining and metallurgy, but is well known as the author of De Re Metallica (‘of things metallic’ or ‘on the nature of metals’), a book that documents and illustrates the observations he made in the course of his extensive travels in the 1500s. Agricola wrote extensively about mining methods and metallurgical processes that were in place in the Middle Ages. The original Latin version of De Re Metallica was published in 1556, the year after Agricola died. It was translated into English by Herbert Hoover, a mining engineer and later President of the United States, and his wife Lou Henry Hoover, a geologist and classicist. The English version of De Re Metallica was published in 1912."

Jan 1, 2012

By M. P. Tixier

Abstract In a review of the application of electrical logging in Canada, examples are .given of long and short distance correlations by means of the electrical logs. The use of MicroLogging for the determination of permeable and porous formations is explained. The question of log analysis for the quantitative determination of fluid saturation and porosity is .discussed. An example is provided to illustrate the significance of the resistivity gradient. The advantages of the new method of the Laterolog are shown, chiefly for the case of wells filled with high-salinity mud. Introduction Electrical logging techniques developed rapidly in Canada at the time an intensive drilling activity started for the exploitation of the Devonian series in Alberta, namely, at the beginning of 1947. The conventional service was soon thereafter supplemented with the latest technica1 improvements. Canada has been among the first regions to take advantage of MicroLogging*, which has proved a most powerful .tool for the investigation of permeable and porous formations; also, the more recent development known as the Laterolog has ?been introduced in Canada. The Laterolog provides a better determination of .the formations, particularly in the case of salty mud where the conventional logging is greatly handicapped. The various methods of electrical logging are now commonly known in oil industry and have been described in numerous publications ( 1) ( 2) (3).

Jan 1, 1951

By A R. Bullis

Metal Mines Limited (Bancroft Division) was incorporated m 1964 to take over the assets of Faraday Uranium Mines Ltd., including their uranium deposit near Bancroft. Ontario. This paper outlines the geology of the Bancroft area, and. then go on to describe the principle rock types m the mine workings, especially the pegmatite, which is the host rock for the uranium mineralization. The structure and mineralogy of the orebodies are thoroughly covered, and, after a summary of the production and ore re-serve figures, the paper concludes with suggestions for further exploration work. Location and History M ETAL Mines Limited, Bancroft Division, is located in Faraday township, Hastings county, Ontario. The main production shaft and concentrator are about: Y2 mile north of Highway 28 and about 5 miles west of the village of Bancroft (Figure 1). The presence of radioactive minerals in the Ban-croft-Wilberforce area has been known since the early 1920&apos;s. Uraninite was found at the Richardson deposit near Wilberforce in 1922, and some attempts were made to produce radium from the deposits of the area between 1929 and 1931.

Jan 1, 1965