Search Documents

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By J. Nesset, F. Rosenblum, P. Spira

Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 500°C. However, most concentrates show little or no propensity to self-heat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.

Jan 1, 2001

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By P. D. Kondos, J. R. Goode

Given the global inventory of low grade and refractory gold deposits, processes that could turn these challenged deposits into mines are of considerable interest. Such gold deposits have low value and potentially high operating costs and so they pose special challenges for the mining engineer and metallurgist. Conventionally, refractory gold ores have been processed by whole ore pressure oxidation and roasting, or flotation followed by roasting, pressure oxidation or bio-oxidation of the concentrate. Halide-based processes have recently been developed that might be applied to concentrates. Low grade refractory gold ores have been processed using heap bio-oxidation followed by cyanide heap leaching or milling. Other processes are emerging. Barrick has completed an inventory of emerging technologies (1). A summary of the current status of these developments will be presented with the view that, with additional development, some of these technologies or a combination thereof may unlock the value of these deposits.

Jan 1, 2005

By L. Bloomquist

This paper describes how Automated Mining Systems (AMS) is evolving the state-of-the-art in guidance systems for autonomous underground vehicles. The techniques, trade-offs, and lessons learned from these systems are described, including the safety regime that has been implemented. First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach. The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system. The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology.

Jan 1, 2004

By L. Bloomquist, C. Arnoldi

"This paper describes how Automated Mining Systems (AMS) is evolving the state-of the- art in guidance systems for autonomous underground vehicles. The techniques, tradeoffs, and lessons learned from these systems are described, including the safety regime that has been implemented.First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach.The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system.The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology."

Jan 1, 2004

"This generic study has been developed in response to the frequently asked question, ""That is the best treatment route for refractory gold ore?"". The study has developed operating and capital costs for many potential treatment routes and they are presented here in a generic form. All costs are in relation to the value of 1.00 given to the base case, a 1000 mtpd bio-oxidation plant, operating at 25% solids and 72 hours residence time.There is unfortunately no simple answer to the above quest ions. The treatment of refractory ores is a complex subject, with many variables, such as mineralogy, chemistry, environment and tonnage. However this study does offer information and relative numbers that we believe will be of assistance to gold metallurgists in obtaining a ""first shot"" at estimating costs.Equally, this technology is a rapidly evolving one. As more plants are commissioned, and test programs completed, better data is constantly being generated. For a generic study of this type to remain useful it will need regular updating and adjustment."

Jan 1, 1989

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By Dan Marshall, David H. Watkinson

Abstract - Cobalt, Ontario, is renowned for the 12.6 billion grams (445 million ounces) of silver produced from the area since discovery in 1903 by workers of the Timiskaming and Northern Ontario Railway. Native silver generally occurs with cobalt arsenides and sulfosalts in near-vertical carbonate veins cutting the Huronian sedimentary rocks of the Gowganda Formation, the Archean metavolcanics and/or the Nipissing diabase. All major deposits have been found within a few hundred meters of the unconformity between the Archean and Huronian rocks in general proximity to the Nipissing diabase and volcanogenic sulfide mounds within the Archean meta-volcanics. Silver has been mobilized from one or more of the local country rocks by hyper-saline brines and deposited in or near zones of mixing where the saline brines encounter paleometeoric water transported to depth along the unconformity or local structures. Previous work has shown that chloride complexes are the dominant ligands responsible for silver transport. These hypersaline brines, represented as halite-bearing fluid inclusions at room temperature, have been trapped as primary fluid inclusions within vein minerals. Pressure-temperature conditions of vein formation have been derived from mineral equilibria, maximum lithostat and fluid-inclusion studies. These data are consistent with vein formation occurring over the temperature range 300°C to 350°C, with pressures constrained between 60 Mpa and 136 Mpa (600 bars and 1360 bars).

Jan 1, 2000

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"Abstract - The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By Roxanne Scott

Outline ? Overview of Community Investment in the Mining Sector ? Emerging Good Practice: ?Strategic Integrated Community Investment? ? Assessing Local Context: ? Institutional Assessment ? Partnership Assessment Approaches to Community Investment Isolation: No proactive engagement in community development Ad hoc philanthropy: small infrastructure, sponsorships, donations Strategic philanthropy: Community proposes options for development Company decides what to do and carries it out, e.g. building schools, health posts, roads Strategic integrated community investment: ? Aligned with government/community development goals and priorities ? Communities and government involved in decisions and execution ? Focused on training and capacity building ? Partnerships ? Continuation in absence of company support Measured returns on investment

May 1, 2010

By J. R. Goode

"Coarse ore sorting is here defined as the physical separation of a mixture of coarse (+3/8 inch) ore particles into two or more separate groups of total value greater than that of the unsorted ore. An ore will probably be sortable if the geology of the orebody and the mining practices employed meet conditions outlined in this paper.The paper points out how sorting can substantially reduce tonnage variable operating costs because sorting can double the mill head grade of amenable ores by rejecting waste rock from the mine output. The effect of sorting on ore reserves is outlined. It is also suggested that sorting is a low cost alternative to conventional expansion.The mode of operation of the Ore Sorters Kadel 13 Photometric and MK VI A Radiometric sorters is detailed. The report concludes with detailed descriptions of the photometric sorting plant operated by the Doornfontein Gold Mining Company is South Africa and the Radiometric Sorting Plant presently under construction at the Schwartzwalder mine of Cotter Corporation in Colorado."

Jan 1, 1975

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, David Grimsey, Denis Shishin

"An integrated nickel flash smelter is operated with Peirce-Smith converters at the Kalgoorlie Nickel Smelter. To improve the partitioning of arsenic between slag waste and matte product, an option to modify the slag–matte chemistry by addition of CaO was analysed. A combination of plant sample analysis, high-temperature laboratory experiments and thermodynamic modeling was carried out to evaluate the process options. The high-temperature experiments involved the re-equilibration of industrial matte-slag samples at 1225 °C and P(SO2) = 0.12 atm, rapid quenching in water, and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LAICPMS). A private thermodynamic database for nickel sulfide smelting and converting was used together with the FactSage thermochemical software package to assist in the analysis of the distribution of elements between slag and matte as a function of CaO addition. The thermodynamic predictions combined with experimental data obtained in this study can be used to characterise the effect of CaO fluxing on the slag–matte thermochemistry during the nickel sulfide converting.INTRODUCTION At the Kalgoorlie Nickel Smelter (KNS), nickel sulfide concentrate is processed in an Outotec-type flash furnace to produce nickel matte containing +47 wt% Ni. Separation of nickel matte and waste slag from the flash smelting is enhanced through settling in the electric arc -heated zone attached to the flash furnace. The flash furnace matte is further processed in a Peirce-Smith converter to produce Ni-rich matte containing +66 wt% Ni (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011). Iron silicate-based slag is used in the converting process at KNS. Most of the arsenic is contained in the final matte and very little of the arsenic partitions into the slag. Previous work by Font et al (Font, Hino, & Itagaki, 2003) shows that the distribution ratio of arsenic between calcium ferrite slag and nickel-matte (LAsslag/matte) is significantly higher than that between iron silicate slag and nickel-matte, where LAsslag/matte = (wt pct As in slag)/{wt pct As in matte} (1)"

Jan 1, 2017

By Michael W. Russnak

Productivity and operating expenses are everything when it comes to judging how well your mine and company are doing. Stakeholders are always looking at these numbers and trying to understand if productivity is improving, if operating costs are trending downward and what you are basing your decisions on. o make improvements you first need to understand how you are performing. If you can?t get this basic information, you will never improve. You will not be able to make simple decisions related to maintenance, operations or production. Forget about planning, as you will only be guessing based on the numbers some stakeholder or your executive wants to see. The problem miners run into is not that the data doesn?t exist; it does, but typically it?s raw, it?s everywhere and its volume is huge. Today there is more on-board computing capability in shovels than we had on our desktops three years ago. Add other mobile equipment, plant systems and multiple OEM vendors to the equation and the challenge is daunting.

May 1, 2007

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

"It is projected that the reactivity of acid generating tailings and waste rock can be minimized by reducing the access of oxygen by placing these materials under water in natural or manmade lakes. A project under the MEND and B.C. AMO Task Forces has been in progress for four years to evaluate active and historic tailing sites in B.C. and Manitoba. The sophisticated geochemistry studies conducted on the interstitial pore water has illustrated encouraging results which are discussed. The additional studies which are needed to complete the scientific database for the study sites, for achieving regulatory and public approval and for the engineering of application of this method of control are outlined.IntroductionWorld wide research effort is in progress to find the solution to the acid mine drainage problem. A great deal is known about acid mine drainage but much work is required to find economic and effective approaches to the problem. Two coordinated programs have been initiated recently in Canada: the National Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Drainage Task Force.Disposal of tailings materials under a water barrier such as a natural lake, is thought to be one solution to prevent acid generation by preventing oxygen and bacterial action on the sulphide surfaces. The deposition of reactive tailings materials under water in natural lakes has been used historically at various mines in Canada. However, there has never been a thorough review of the long and short term impacts of historic sites which may provide crucial information to understand the physical, chemical and biological processes which are taking place.This paper provides a general overview of a series of studies which examine the general biophysical characteristics and the sediment geochemistry of four lakes where subaqueous disposal has been or is currently being used for acid generating tailings. The subaqueous disposal studies have been conducted from 1989 through 1991 and were initiated and supported by both research task forces. The objectives of this paper are to summarize the history and the background information of the studies conducted, the general results obtained from each lake, an overview of the major collective results and the additional work which is required to achieve the final objective of developing criteria for applying this technology in the industry."

Jan 1, 1992

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976

By A. H. Winckers

"CAMIRO, The Canadian Mining Industry Research Organization, formerly known as MITEC, is a collaborative research organization of Canadian Mining Companies. It is comprised of Exploration, Metallurgical Processing and Mining Divisions.The Metallurgical Processing Division (MPD) has the mandate to contribute to the profitability, competitiveness, safety and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral processing and extractive metallurgy in an environmentally conscious manner through the development of innovative technology by managing cooperative industry focused research programs.Current membership includes about ten Canadian mining companies. Past research has largely focused on base metal mineral processing. The Division wants to expand its research base to include all areas of mineral processing and extractive metallurgy.Past performance and plans for the future will be highlighted in the presentation."

Jan 1, 1998