Search Documents

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By Jefferson CW

Middle-to-Late Proterozoic stratigraphy and metallogeny in the eastern part of the Canadian Cordillera and in South Australia are strikingly similar. In both areas, thick, predominantly shallow-water strata and their contained mineral deposits can be divided into three sequences (A, B, C) that record episodic and prolonged continental rifting. It is proposed that Adelaidean strata of Australia were deposited adjacent to Belt-Purcell, Mackenzie Mountains and Windermere strata of the Canadian Cordillera within an epicontinental trough of a "Hudsonia" regacontinent. With the final rifting of this trough, the paleo-Pacific ocean was born. By Early Cambrian time, Australia- Antarctica was on the trailing "east" side of the nascent megacontinent, Gondwana, and was being modified on the "west" by accretion in the Pan-African event. North America, more or less surrounded by trailing edges at this time, was analogous to the Cenozoic African plate. This hypothesis accommodates the available paleomagnetic and radiometric data. It has implications for pre-Pangean plate tectonics, paleogeography, and the predictive metallogeny of both areas.

Jan 1, 1987

This paper describes modern long-term mine scheduling and gives an example of its application. It then discusses the obstacles to the implementation of such schedules.

Sep 26, 2011

Various software packages are discussed. These are components of an Integrated Planning and Scheduling System developed by MVM with the aim of providing up-to-date information for the Whaleback operation on: 1. Mine Topography. 2. Status of equipment in the mine. 3. Material moved from and within the mine. 4. Volume and density of same. 5. Quality of same.

Jan 1, 1986

Environmental management of minesites in general, and management of water discharges in particular, is receiving ever-increasing attention. One key component in the successful design and operation of water management systems is to address the presence of sediment in the water being conveyed. Sediment erosion in the mining environment is often greatly exacerbated by disturbing the ground surface of vast areas of catchment. If sediment avoidance, transport, deposition or release are not adequately addressed, the impact on water management facilities can include loss of storage and hydraulic capacity, more frequent equipment replacement, increased operational costs and potentially environmentally unacceptable sediment discharges to receiving waters. An overview of sediment management within water facilities is presented here, and design of one particular approach, the use of settling basins for sediment removal, is discussed in detail. Examples are used to illustrate lessons learnt where particular approaches to sediment management have been found to be lacking. The common themes in the lessons learnt include the need to characterise hydrodynamic conditions and sediment properties in the water source, to set performance targets for sediment management, and to develop operating procedures to meet these targets under a realistic range of scenarios. The examples show how analysis of expected performance of sediment management can help with planning of operation and maintenance strategies. For settling basins, use of a simulation model that includes the effects of turbulence on settling can provide considerable benefits in optimising basin design and evaluating performance. Even in the most basic approach to sediment settling, establishing performance targets based on design flow and sediment characteristics is critical.

Jan 1, 2003

By T Laing, M A. Abdalla, P Hagan

Open pit operators are facing a number of challenges in the area of blasting and blasting processes, such as wall control, quality of fragmentation, explosives consumption and vibration. Remaining financially viable is one of the most significant objectives for mining professionals as they work through the blasting challenges within the mining chain of processes. This objective is such a significant challenge, primarily due to the high consumption of materials and the direct consequences on the downstream processes in the mining work flow, including loading, hauling, crushing, milling and mineral concentration. This paper reviews and discusses a technique to achieve this objective, namely air-decking. The performance in a number of mines around the world is reviewed focusing on the economic contributions of air-deck blasting. Various scenarios are investigated and simulated, covering both conventional and air-deck blasting, using JKSimblast software. The scenarios explore a range of issues and found that optimum results could be achieved with a minimum amount of explosives. The results obtained from the simulations were verified with blasts at Rixs Creek Coal Mine, Australia. Based on the verification results the simulations were then modified to more accurately model the actual conditions and parameters on site and to ensure that the models derived meet the production and control requirements at the mine site. Ultimately, overall analysis and comparisons were applied to the outcomes of the conventional and air-decking blasts revealing a reduction in material consumption of around 25 per cent with consequential savings and up to a 30 per cent reduction in ground vibration.CITATION:Abdalla, M A, Laing, T and Hagan, P, 2012. The contribution of air-deck blasting to open pit mining economics, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 7-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Clarke RG

Renison Mine was developed as the first all diesel mine in Australia. The foresight of the early planners in committing the Mine to Decline access has paid dividends in the past two decades with Renison Mine establishing itself as one of the most productive underground mines in the world. The excellent productivity has also resulted from the development of mining equipment technology, both on the part of the equipment suppliers and through the coordination of the Mining, Automotive and Technical Design Sections at Renison Mine. Constant improvements in truck and loader design, the design of specific equipment to carry out specialized tasks such as installation of services, scaling and ground support and the conversion to electrically powered equipment have been ongoing at Renison. Currently, larger scale trucks are being investigated for ore and waste haulage due to increased haulage distances and production requirements. It appears as though an articulated low profile truck of around 50 tonnes capacity may provide the short term solution based on the performance data available.

Jan 1, 1982

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

Folklore suggests that oxidation is detrimental to sulfide mineral flotation, and in many instances is the reason given for values reporting in the tailing. However, while a considerable body of work examining galena oxidation is available in the literature there are very few studies that investigate the consequences of galena oxidation on its subsequent flotation in base metal sulfide ores. This work clearly demonstrates that pyrite forms a galvanic couple with galena, due to the large difference in their rest potentials, and results in accelerated oxidation of galena, particularly as the pyrite content of the ore is increased. The most obvious effect of the galvanic oxidation of galena by pyrite is the release into the system of galena oxidation products, providing an ample supply of lead ions available to activate gangue minerals, most notably of which in lead/zinc ores is sphalerite. The inadvertent activation of sphalerite by lead ions inevitably leads to the recovery of liberated sphalerite into the lead concentrate, and as a consequence a reduction in the lead concentrate grade. That is, a loss of selectivity for galena against sphalerite. If galena oxidation is excessive not only is there a considerable loss in lead concentrate grade, but also a marked decreased in lead recovery as the flotation rates of the gangue minerals increase, until they rival that of galena.

Jan 1, 2005

By Jones KW, McClelland RA, Denholm WT, Taylor RN, OÆShea J

Associated Tin Smelters, Sydney, are developing tin smelting operations in a prototype commercial SIROSMELT plant comprising two furnaces of 5 to 8 tonnes capacity. Features of the plant and its operation are discussed and results of its application to tin slag reduction and high-grade tin concentrate smelting are presented. Development work is still in progress but experience indicates that the technology has potential for lowering the costs of tin smelting and relieving constraints on grade and iron content of concentrate imposed by conventional technology.

Jan 1, 1984

Exploration for uranium in Australia commenced only during the 1940s, but in this short period has been very successful as one third of the world's low cost uranium reserves have been discovered in Australia. Total uranium exploration expenditure in Australia up to the end of 1983 was $A(1983) 554 million; this discovered 20 potentially economic deposits and official reserves of 560 000 tonnes of uranium oxide at an average cost of $1 per kg of U 0 . An exponential 8 eserves indicates distribution of uranium r that there could be 54 undiscovered uranium deposits in Australia, each with reserves of 20 000 tonnes U308 or more, in addition to smaller deposits. Using a constant uranium price of $A(1983) 79 per kg, no deposit is economic at a grade below 0.12 per cent U 08 or with reserves of less than 3 000 tonnes. Selecting deposits with reserves of 5 000 tonnes U 0g or more as prime exploration targets, only 39 per cent of discoveries will yield a real internal rate of return (IRR) of 10 per cent or more. After committing a minimum exploration budget of $10 million to this search, an explorer has one chance between 7 and 12 of discovering a deposit that will repay the exploration investment.

Jan 1, 1984

Selection of mining methods, stope dimensions and stoping sequences is usually based on comparisons with other similar orebodies or rocktypes. Rock mechanics principles assist the process, which can be further improved by application of rock mechanics' models - in particular, computer based stress analysis techniques. These models vary in capabilities and potential application but, basically, can be subdivided into techniques which only model the surface of excavations, and those which model the total volume to be analysed. To address the wide range of geometries, stoping methods and sequences, and geomechanical environments at Mount Isa Mines, a number of models have been developed. By presenting examples of their actual and potential application it is demonstrated that appropriate use of these techniques will assist in the determination of mining parameters and improve ore recovery. Examples presented cover sequencing in tabular and massive orebodies, location of shafts and shaft pillars, and backfill and hanging-wall stability. It is concluded that surface techniques are more appropriate for regional analyses and volume techniques are more suited to analyses of detailed, local geometry. Colour computer graphics should be an integral part of data preparation, and results interpretation and Presentation.

Jan 1, 1986

By T Leach, F Kaiqiang

The Jianchaling gold deposit is located about 1200 km south west of Beijing in central China. The deposit was discovered in 1988 by the Northwestern Geological Exploration Bureau (711 Exploration Team). Sino Gold Limited, an Australian based company, developed the mine in 1998 and is currently operating a 1000 t per day underground mine, producing about 80 000 ounces of gold per year. The pre-mine resource for Jianchaling was 1.6 million tonnes at 9.85 g/t gold. The deposit occurs within the east-west trending Mesozoic Qinling-Dabie orogenic belt formed during the Yanshanian Orogeny. In the Jianchaling region, gold mineralisation is primarily hosted by regional west-northwest to east-southeast striking faults, the most important of which, the reverse sinistral F145 fault, hosts the larger gold deposits including Jianchaling. At the mine scale, the most important zone of mineralisation is localised within a shallowly north dipping dilation on the F145 fault. Proterozoic dolomite forms the hangingwall and serpentinite and talc schist the footwall to the fault. Within the footwall, serpentinite is the most important host rock to mineralisation. Initial alteration involves replacement of serpentine to dolomite ¦ pyrite, talc to ankerite ¦ pyrite, and magnetite and chromite to pyrite, the latter locally through a transitional hematite phase. Proximal to feeder structures, the carbonate minerals have undergone partial dissolution and replacement to quartz. Gold is related to arsenean pyrite and marcasite rimming and replacement of early-formed pyrite, and associated with iron release during the processes of dolomitisation, silicification and carbonate dissolution.

Jan 1, 2004

By G Reynolds, N A. Ware, L Lu

Queensland Pacific Metals (QPM) is progressing its Townsville Energy Chemicals Hub (TECH) project to produce nickel and cobalt sulfates for advanced battery materials. Apart from the nickel and cobalt sulfates, the process also generates a hematite by-product (~640 ktpa). The hematite byproduct precipitated from the process, hereafter ‘hematite precipitate’, is high in Fe and particularly low in impurities. However, it is a fine <20 μm crystalline, hydrometallurgical precipitate and is produced as a filter cake containing a high moisture content of about 15 per cent. This is considerably different from natural hematite ore and is expected to change its performance during sintering. In the present study, laboratory scale sintering tests were undertaken to evaluate the potential impacts of substitution of the hematite precipitate for traditional magnetite concentrates and further for Australian hematite-goethite ores in a simulated industry base blend. Substitution of hematite precipitate for magnetite concentrates was found to slightly increase the sintering temperature required to achieve the strength of laboratory sinters. However, further substitution of hematite precipitate for Australian hematite-goethite ores slightly reduced the sintering temperature required to achieve the laboratory sinter strength. These results reflect the reduction in Al2O3 contents of the blends and are consistent with the trend observed in industry and pilot scale facilities. The reduction in sintering temperature generally correlates to a reduction in fuel rate in the larger scale sintering process. The pore structure of selected laboratory sinters was further examined and discussed in conjunction with sinter strength. The pore structure images highlighted the relative difference between the blends with the most obvious difference being seen at 1290°C which correlates well with the laboratory tumble index (TI). The laboratory sinter samples showed an increase in porosity and irregularity of pore shape, as hematite substitution increased demonstrating the correlation between a more porous structure and a lower TI.

Sep 18, 2023

By Perring CS, Hill RE, Barnes SJ, Vallance SA

The Maggie Hays nickel sulphide deposit is located at latitude 32¦ 15 &apos;S, longitude 120¦ 30&apos; E on the Lake Johnston (SI 51-1) 1:250 000 map sheet. The deposit occurs in the Lake Johnston greenstone belt, in the Southern Cross Province of the Archaean Yilgarn Block, 500 kilometres east of Perth, Western Australia (Figure 1). The remoteness of the Lake Johnston greenstone belt and its poor access, restricted previous exploration activities and the full appreciation of the geology and its Ni-sulphide potential. It was not until 1991, when Forrestania Gold NL commenced exploration activities, that the geology of the ultramafic units and their potential to host significant concentrations of Ni sulphides were clearly established. This paper, which describes the geology and the characteristics of the Maggie Hays deposit, is based on the results of exploration by Forrestania Gold NL and a collaborative research agreement between CSIRO Division of Exploration and Mining and Forrestania Gold as reported by Perring, Barnes and Hill (1994), Perring and Hill (1995), Perring (1995 a and b) and Barnes, Perring and Reilly (1995). A comprehensive description of the geology, petrology and geochemistry of the deposit is being prepared for publication by CSIRO (Pemng, Hill and Barnes, in press).

Jan 1, 1996

From depths of 400 - 600 m, coal is transported by a conveyor in a drift or a bulk winder in a shaft, whilst men and/or materials are transported by a slope hauler or a cage winder. Assessment of the effect of alternative combinations on the key cost factors - output, capital, labour cost and construction time - allows the optimum choice for particular circumstances, there being no uniform solution.

Jan 1, 1976

Answers to many questions arising in the different phases of exploration, estimation and production of a mineral deposit, can be found in the geostatistical theory of G. Matheron. It is shown that all these questions regarding sample size, number of samples, shape of drilling pattern can be answered as soon as the continuity of the mineralization is quantitatively characterized by means of a variogram. Next a formula which gives the variance of the error associated to any estimation procedure (i.e., any method and any sampling pattern) is given. Applications to the computation of the standard error of the&apos;mean for various sampling patterns are shown, as well as how to use the formula to simulate several possible sampling strategies and choose the best one. Altogether it is shown how to answer the often heard question, "what happens if such and such sampling procedure is used?", rather than giving an hypothetical "optimal" solution.

Jan 1, 1976

By Shrivastava P, Humphreys M, Guibal D, Deraisme J

Customer requirements concerning the final products of iron mines are extremely stringent. Because of this, there is an ever-increasing need for mine operators to monitor and strictly control the quality of their product. This quality, as measured by the stockpile grade variability, is the result of a very complex process, where natural characteristics (the orebody and its geology) are transformed through the mining technique (open pit, shovel and truck fleet, blending into stockpile). The only way to reproduce and hence to control the variability of such a system, which is composed of several interactive sub-processes, is by simulation. A complete simulation of a Hamersley Iron Pty Ltd (HI) ore deposit has been undertaken to forecast the impact and cost of various mining methods, mining schedules and product stockpile sizes on variability of chemical and physical characteristics of the products. The mining simulation was made on a conditionally simulated orebody. On a range of criteria, the simulation was considered to fulfil the objectives set and was a valuable aid to analysis of product grade variability, operating and capital costs, selection of equipment, mine scheduling and setting of product grade targets.

Jan 1, 1994