Search Documents

By Thomas Donnelly

Introduction THE Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineralization is found about 1.-CAMP BUCARO. THE TOP OF THE RIDGE IN THE BACKGROUND MARKS THE CONTACT OF THE LIMESTONE AND TUFFS. S miles north of the town of San Cristobal, in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina (Liver. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horse-back 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 8, 1915

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush's work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

A New Ingersoll-Rand Turbo Blower The Ingersoll-Rand Co. has added to its Turbo Compressors and Blowers a low-pressure machine t o handle volumes from 3,000 to 35,000 cu. ft. per minute at from 1-2 ½ lb. These are particularly adapted to such service as foundry cupola blowing, atomizing oil for oil burners, supplying blast to heating and annealing furnaces of various kinds, blowing air for water-gas generators, pneumatic conveying and ventilating. They are of the single stage, double flow type and are furnished either electric motor, steam turbine or water wheel driven.

Jan 6, 1916

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

By Willard P. Ward

SOME TIME in the year 1874 or 1875, I conceived the idea that spiegeleisen might be made -in a blast furnace from ores that were not carbonates, and which did not contain both manganese and iron in the same ore. Up to this time, such ores had formed the basis of all the spiegel that had been produced; and all the ferromanganese that was on the market before 1875 was made in crucibles, and cost about 00 per ton, for 80 per cent. Mn. I consulted the great steel metallurgist of the day, Alexander Holley, who listened attentively to what I had to say, and told me he did not think my plan was practical, so I abandoned it for the time being. But I was so stubborn that I could not get the notion out of my head. It seemed to me that a good metallurgist should be able to work the thing out in some way. I had already had some experience in smelting refractory lead ores in Utah, and was young and not lacking in self confidence, so after waiting a bit, I got Anton Eilers, the best all-around metallurgist I knew, and J. H. Bramwell, the best iron blast-furnace man I knew, both intimate friends of -mine, to come to my place in Bartow County, Georgia, and look over things. They remained for several days, and made all the examination they thought necessary; and they also advised me to give up the project, and either to keep the furnace running on car-wheel iron or to blow it out. After my talk with Holley, I improved my plant in several ways. I closed the top of the furnace, put in a hot-blast stove, a steam boiler and a Weimer blowing-engine which gave me blast enough, at a pressure high enough for all the requirements of, the furnace, and which I could bring up to a temperature of 600° to 700° F.

Jan 1, 1921

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By KENNETH CROPPER

USUALLY we forget about the things which move along smoothly. There are no causes for worry when there are no troubles. But when troubles arise we must put forth some thought and effort to alleviate them. No one "worries about his automobile until it begins to knock, develop flat tires, or refuses to start. However, when these ailments become apparent we get wide awake on the spot, and do our best to repair the car. So we find ourselves now. The old bus seems to hit all the ditches. There is rough ground on all sides and none of us is able to do anything toward improvement. A state of pessimism stares us in the face, and there is sufficient cause for it. With lead at 3.75 cents, copper about 8 cents, zinc under 4 cents, -and silver about 26 cents, one has a reason for grief. When we think of the 5000 or less men employed in Utah mines and smelters in 1931, as compared with about 12,000 in 1929, the calamity seems even worse. In view of the present economic crisis we cannot even think of new men getting a job.

Jan 1, 1931

By John Chipman, Peter J. Koros

The distribution of copper between liquid silver and liquid iron, Fe-C, and Fe-C-Si alloys was studied at 1600°C. From the data and the activity of copper in silver obtained from the phase diagrams, the activity coefficients of copper in iron up to 3 atomic pct are log y, = 0.90 — 2.4 N, and y": = 8.0. The effect of carbon up to saturation is expressed as log y = 1.8 Ni. The effect of silicon up to 11 atomic pct is insignificant. SLOWLY rising copper content of steel being produced is focusing attention on the lack of information on the behavior of copper in liquid steel. Chou' measured the activity coefficient of copper in liquid iron through its distribution between liquid silver and iron. He obtained a value of 9.12 at infinite dilution. Chipman' calculated the activity coefficient of copper in liquid iron at 1600°C from the phase diagram and obtained a value of 12. Ameiln and Pfeiffer- investigated the possibility of removing copper from liquid steel through the use of lead, silver, and bismuth as solvents. They also calculated that the activity coefficient of copper in liquid iron would be increased five or sixfold by addition of 4 pct C. Langenberg and Lindsay' are investigating the effectiveness of lead and sodium sulfide in removing copper from liquid iron. The experimental method was similar to that used by Chou' and Chipman and Floridis." Silver, copper, and iron were melted together, the copper distributing itself between the two layers so that at equilibrium a,.,, (in Ag) - a,.,, (inFe) and N,.,, (in Ag) yc,, (inFe) (in Ag). [21 N,.,, (inFe) Thus, from the concentration of copper in each layer and the activity coefficient of copper in liquid silver, the activity coefficient of copper in liquid iron can be calculated. The effect of an alloying element such as carbon on the activity coefficient of copper can also be determined from its effect on the distribution, provided the new element is essentially insoluble in silver. The one serious limitation of this method is the increasing mutual solubility of silver and iron in the presence of a third component. The mutual solubilities of pure iron and silver are negligible, but increase with increasing copper concentration beyond the range investigated. Ag-Cu System—The activity coefficient of copper in silver at 1600°C had to be estimated, since direct experimental data are not available. Kawakami" measured the heat of mixing of Ag-Cu alloys at 1200°C by a calorimetric technique. Scheil' calculated the heat of mixing in this system by use of the phase diagram, assuming that the solution is random and that the heat of mixing is independent of temperature. The terminal solid solution may be assumed to obey Raoult's law within the requirements

Jan 1, 1957

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form .of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition-of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some. Secondary Non-ferrous Metals Recovered in the United States for the -Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 8 71,170,400 Brass, scrap remelted : 242,300 56,270,800 Lead as metal : 112,420 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc in alloys other than brass 13,300 Tin as metal 7,950 Tin in alloys 23,000, 35,165,400 Antimony as metal 1 3,794,000 Antimony in alloys : 10,839 Aluminum as metal 17,700 24,816,000 Aluminum in alloys 26,300 Nickel as metal 191 1,518,000 Nickel in non-ferrous alloys 2,109 Total l 882,600 $243,570,700

Jan 1, 1928

By Alfred H. Bell

IN 1945, Illinois produced 75,210,000 bid. of oil, or 4.4 percent of the total for the United States, and ranked sixth in the nation in oil production for the third consecutive year. Production decreased about 3 per cent from that of 1944, when the total Illinois production was 77,413,000 bbl. This is the smallest percentage of decrease in production in the state for any year since a peak was reached in 1940. Daily average production for 1945 was approximately 206,000 bbl. Daily averages by months were as follows:

Jan 1, 1946

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By F. Haessner, M. Wilkens, U. Jakubowski

ThOUGH at present there is a wide range of possibilities for the quantitative determination of preferred orientations, pole figures of identical specimen material have not been determined by different methods as yet.''' In this paper a comparison of (Ill), (200), and (220) pole figures is presented which were obtained from a 95 pct cold-rolled high-purity cop- per sheet (99.9998 pct Cu), by three different methods. The three methods are: a) The combined X-ray reflection-transmission technique of plane samples by schulz3 and Decker, Asp, and Harker. 4 A Siemens texture goniometer was used. The experimental details are described elsewhere. 6 b) The X-ray reflection technique of spherical samples by Jetter and Boric.' A Siemens texture goniometer with some modifications was used. The samples were prepared by sticking 140 polished sheets together with an adhesive and machining a sphere (20 mm diam).* Additional

Jan 1, 1967

By M. ROWE, H. E. Gilliland, L. BARNES

The authors of this paper are to be commended for a clear exposition of a timely subject. However, some important conclusions, in addition to those presented in the paper, can be drawn from the results of their elaborate and rather complete numerical computations. First of all, the major part of the calculations presented in the paper are for semi-infinite slabs of oil shale (the authors designate this as Model I) and a question must be posed — Are these elaborate computations needed to arrive at realistic estimates of the shale oil displaced. Consider the model of Lauwerier* that corresponds to the authors Model I if thermal conduction parallel to the fracture be neglected. If one also neglects the finite (but relatively small) heat capacity of the material in the fracture, it is easily shown from Lauwerier's solution that the cumulative oil production would be:

Jan 1, 1969

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

A regular general meeting of the Canadian Mining Institute will be held in Vancouver, B. C., on Nov. 26-28. The Council extends a cordial invitation to all members of the American Institute of Mining and Metallurgical Engineers to attend.

Jan 11, 1919