Search Documents

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Dwight K. Smith, Greg Carter

Studies have been conducted on The properties of many deep well cementing compositions to determine their Strength behavior over curing periods to 180 days at elevated tem-peratures and 3,000 psi pressure. This pressure results in essentially the .vat, compressive strength as that obtained with much higher pressures in ac-cordance with the findings of an API subcommittee ' These different compositions include API C1asses A, E, and F cements containig additives such as retarders, berrtorlite, heavy weight materials and pozzolans. All compositions except mixtures of Poz-zolrrrts and hydrated lime show from mild to severe degrees of strength lass over a temperature rang from -730 to 320" F after setting. Pozzolatl-time compositions actually gain in strength with time at these high temperatures. Other chemical find physical properties evaluated to observe their inter-relation.ship with Strength loss show very little correlation except in per-meability. As retrogression in strength increases, the permeability of set cement increases. X-ray difraction patterns on the set products indicate the formation of certain compounds having little or no strength value in those cementing compositions where strength loss was more severe. INTRODUCTION As a result of the growing trend toward deep well completions, a study has been made on the properties of the various cementing slurries presently in use at elevated temperatures and pressure. The strength of these compositions is of prime importance in selecting the most suitable material for use at high temperatures, to determine WOC time and the proper time to perforate with a minimum of shattering. Of primary interest in this investigation was the strength behavior of various compositions currently in use, and the effect of additives on cement after long periods of curing under severe conditions. Earlier investigators have pointed out that the strength of some cements will increase with increasing curing temperature to about 220 to 340" F, but at higher temperatures a loss in strength occurs at extended time intervals. Studies by the API Mid-Continent District Study Committee on Oil Well Cements' outlined a testing procedure whereby field conditions of temperature and pressure could be simulated in the laboratory.' It was observed that retarded cements undergo changes at elevated temperatures and some lose as much as 50 per cent of their early strength when cured at high temperatures. The scope of these tests was limited to curing periods of 1 to 28 days; additives were not covered in this study. Saunders and Walker' found that the use of additives influenced the strength behavior of cements at high temperatures, but studies were conducted only to a seven-day curing period. Ludwig and Pence' conducted an investigation of two types of cements under elevated pressures and temperatures in an effort to explain the causes of this loss in strength phenomenon. It was observed that with retrogression in strength there were other physical and chemical changes which took place as the cement aged. Today there are a number of cementing compositions available for use at well depths below 10,000 ft. Since all these earlier investigations were limited in curing time as well as the number and type of compositions studied, it was believed that a more extensive study should be conducted on the properties of cements at elevated temperatures, and this work should include those compositions actually in general field use at this time.

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By F. J. Fayers, R. L. Perrine

For many years the problem of increasing ultimate recovery of oil from a reservoir has been a subject of interest to the oil industry. At present, a standard secondary recovery technique is to flood the reservoir with water once natural forces of the system are depleted. The permeability characteristics of the rock, together with interfacial forces which exist between the two fluids and the porous material. allow only part of the oil in the rock formation to be recovered by the water-flooding process. Laboratory experiments have shown that when detergents are added to the flooding water, the flow properties of oil in a porous rock arc improved. This improvement results in greater oil recovery. Even though higher recoveries are obtained using detergents, the extra cost associated with the method may make it economically unsatisfactory. To establish economic feasibility requires experimental laboratory measurement of fluid and rock properties together with a calculational procedure to predict field results. Pilot tests in the field may also be required. This paper presents a mathematical procedure for predicting detergent flood behavior. A number of reasonable simplifying assumptions are made to obtain a tractable system of equations. The resulting method may be regarded as a generalization of Buckley-Lev-crett' theory to solve simultaneously for water saturation and detergent concentration profiles. Consequently this type of calculation can be used in much the same manner as Buckley-Leverett theory is used to evaluate a water flood. The mathematical method employed is the so-called method of characteristics for solving hyperbolic partial differential equations. This application of the method is instructive because several other problems in reservoir analysis may be analyzed in a similar manner. FLUID FLOW EQUATIONS The flow behavior of oil and water without detergent through porous reservoir rock is usually expressed by Darcy's law and a continuity equation for each phase. If gravitational forces are neglected, vrg = kr (s)µr v p rg.........(1) vrg = kr (s)µr v p rg.........(1) ? pa va = F ?/?t (sd) where v is the volumetric flux, k represents permeability, S is saturation, and P the pressure. Fluid viscosity is denoted by 11, p is the density, 4 is porosity, and I the time. The subscripts w and o refer to water and oil. The capillary forces in the system lead to a difference in pressure between phases. This may be expressed by the relation: Pm -P0 =Pc(S).........(5) The capillary pressure? P,, is determined experimentally as a function of saturation. DETERGENT BALANCE EQUATION Addition of detergent to the water phase affects the flow properties of the system. Capillary pressure and relative permeability become functions of detergent concentration, c, as well as fluid saturation. That is: P--P (S,c) and k,,,.- - -- k,,,. At low oil saturation values, the presence of detergent reduces capillary pressure and reduces the relative permeability ratio. Detergents are surface-active and adsorb on rock surfaces. The quantity adsorbed, a, will depend on the concentration c of detergent solution and may also depend on the saturation; thus, a = a(S,c). In this analysis we have assumed that the detergents used are water soluble but not oil soluble, and their movement is therefore restricted to the water phase. The dispersion of detergent in water is neglected by comparison with transfer by flow within the system. Detergent movement is determined by the water flux and adsorption: ? cv m = -F ?/?t (cs + a) We will assume that the quantity of detergent in solution is too small to significantly change water density or viscosity. When the permeability and capillary pres-

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during December: William M. Peschel, Bradford, Mass. Samuel T. Wellman, Cleveland, Ohio. Herbert B. Cox, Boston, Mass. Samuel S. Wyer, Columbus, Ohio. C. Q. Schlereth, Mexico, D. F. H. H. Stoek, Urbana, Ill. H. W. Caldwell, Oxford, N. C. E. Harms, Torreon, Mexico. Charles E. Schwarz, St. Louis, Mo. G. A. Roush, So. Bethlehem, Pa. Dwight Furniss, Guanajuato, Mex. M. K. Rodgers, Los Angeles, Cal. F. W. DeWolf, Urbana, Ill.

Jan 1, 1914

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By Walter H. Bucher

This symposium is designed to lay the basis for a general discussion of the place of geophysics in the training of geologists. As there is danger that in the ensuing debate individual interests may be given emphasis out of proportion to their place, we shall do well to view the whole field of geological inquiry in order to see the problem in true perspective. The Nature of Geological Inquiry "Basic" and "Complex" Sciences It is convenient to divide all science into two major divisions, the basic and the complex sciences. The basic sciences separate out from reality such entities as "substances" and "movements," describe their behavior in terms of arbitrary units of measurement and derive from them by progressive abstractions concepts and patterns of behavior that exist between them, so-called general "laws" and "properties" of nature. The complex sciences, on the other hand, deal, with little or no abstraction, with those objects of reality that are accessible to man in the atmosphere, the hydrosphere, the lithosphere and the biosphere. Their work comprises two types of inquiry. One is concerned with abstractions to the extent of dealing with types rather than individuals—that is, with such things as plants, animals, protoplasm; clouds, streams, gla- ciers; volcanoes and mountain ranges. It comprises the search for general properties and patterns of behavior or "laws" that characterize the objects and their reactions to each other. These properties and laws apply always, everywhere. They are independent of the stream of time. We may call the results of this sort of inquiry timeless knowledge. The other type of inquiry is concerned with the objects themselves—that is, with this animal and that plant; this river system and that mountain chain; this glacier and that valley. Like all concrete objects in nature, they are subject to change with the passage of time, especially when it is measured in years, centuries, eons. The characteristics by which we recognize them —indeed, their very existence—are dependent on their position at this point in the stream of time. This we may call time-bound kntowledge. The so-called descriptive sciences are all bound to the past of which the objects of their study are the product and through which alone their present properties call be understood. They are historical sciences. This obvious fact is easily overlooked, which leads to serious misunderstanding, as we shall see later. Dynamic Geology With this broad picture in mind, let us now examine the nature of geological inquiry, defining, for the purposes of this discussion, geology as the science of rocks. Air is not a rock; water is. Meteorology and climatology are, correspondingly, gen-

Jan 1, 1946

By Walter H. Bucher

This symposium is designed to lay the basis for a general discussion of the place of geophysics in the training of geologists. As there is danger that in the ensuing debate individual interests may be given emphasis out of proportion to their place, we shall do well to view the whole field of geological inquiry in order to see the problem in true perspective. The Nature of Geological Inquiry "Basic" and "Complex" Sciences It is convenient to divide all science into two major divisions, the basic and the complex sciences. The basic sciences separate out from reality such entities as "substances" and "movements," describe their behavior in terms of arbitrary units of measurement and derive from them by progressive abstractions concepts and patterns of behavior that exist between them, so-called general "laws" and "properties" of nature. The complex sciences, on the other hand, deal, with little or no abstraction, with those objects of reality that are accessible to man in the atmosphere, the hydrosphere, the lithosphere and the biosphere. Their work comprises two types of inquiry. One is concerned with abstractions to the extent of dealing with types rather than individuals—that is, with such things as plants, animals, protoplasm; clouds, streams, gla- ciers; volcanoes and mountain ranges. It comprises the search for general properties and patterns of behavior or "laws" that characterize the objects and their reactions to each other. These properties and laws apply always, everywhere. They are independent of the stream of time. We may call the results of this sort of inquiry timeless knowledge. The other type of inquiry is concerned with the objects themselves—that is, with this animal and that plant; this river system and that mountain chain; this glacier and that valley. Like all concrete objects in nature, they are subject to change with the passage of time, especially when it is measured in years, centuries, eons. The characteristics by which we recognize them —indeed, their very existence—are dependent on their position at this point in the stream of time. This we may call time-bound kntowledge. The so-called descriptive sciences are all bound to the past of which the objects of their study are the product and through which alone their present properties call be understood. They are historical sciences. This obvious fact is easily overlooked, which leads to serious misunderstanding, as we shall see later. Dynamic Geology With this broad picture in mind, let us now examine the nature of geological inquiry, defining, for the purposes of this discussion, geology as the science of rocks. Air is not a rock; water is. Meteorology and climatology are, correspondingly, gen-

Jan 1, 1946

By A. Boltax

H. Herman and M. E. Fine (Northzcesteriz University)—The author is to be complimented on the quality and completeness of his work. Of special interest to us was the exponent of time in the exponential rate equation, n = 0.28 ± 0.03, since it is consistent with results for the early stage of quench-aging in A1-2 at. pct Cu, n = 1/3, first determined in this laboratory."' In that work we attributed the early kinetics to attraction of vacancy - solute atom complexes to the plate-shaped zone due to the strain field about the zone and the lowering in free energy. To our knowledge, Hirano et 1.' were the first to

Jan 1, 1962

By Lendall P. Warriner, Blandford C. Burgess

Jasper County lies just north of the geographical center of Georgia, bounded on the west and north by the Ocmulgee River. The county seat, Monticello, is approximately 65 miles east-southeast of Atlanta and 40 miles north of Macon. It is served by the Macon-Athens branch of the Central of Georgia Railway Co. and by five paved highways converging from adjoining county seats. Farming and lumbering are the principal local occupations. About half the county is covered with pine and mixed hardwoods; a large part of the forested land is owned by the Soil Conservation Service of the Department of Agriculture in its Piedmont Land Utilization Project. The topography is one of gently rolling field and forest with occasional hills rising 100 ft or more above the creek beds. Though annual rainfall is in the neighborhood of 60 in., most of it falls in torrential downpours of short duration which tend rapidly to erode the red soil and convert the country roads to greasy tracks of red mud. History The pegmatites of Jasper County produced a small amount of mica in World War I. In World War 11, our Government's search for this strategic mineral brought to Georgia B. C. Burgess, then Southern Manager of Colonial Mica Corp., subdivision of Metals Reserve Corp., who noted on State Highway 83 the presence of pegmatitic material used as road metal. In 1944, after severing his Government connection and returning to private practice, Mr. Burgess investigated the source of the pegmatitic material noted on his previous visit and discovered that graphic granite pegmatite had been mined for the road metal. He secured mineral leases from the Soil Conservation Service and from private owners and began preliminary development work. By 1946 he had uncovered enough pegmatite to warrant an enterprise to undertake economic development of the feldspar. In March 1947, he conveyed his leases and interest to Appalachian Minerals Co., remaining with it as Vice President and General Manager. This company has carried on additional development, removing overburden by bulldozer and drilling the pegmatites uncovered. A modern and efficient feldspar grinding plant to produce 20 mesh feldspar for the glass industry was completed and placed in operation May 1, 1948. Geology GENERAL GEOLOGY OF ROCK TYPES OTHER THAN PEGMATITE Jasper County lies within the Appalachian Crystalline Complex and approximately 40 miles north of the "Fall Line," where the Upper Cretace-

Jan 1, 1950

By Heinrich 0. Hofman

A T THE meeting of the Board of Directors on June 24, Prof. Heinrich O. Hofman was elected an honorary member of the American Institute of Mining and Metallurgical Engineers. Professor Hofman is best known to the world at large for his publications, and in this respect he is to this generation what Schnabel was to the previous one. The first edition of Professor Hofman's "Metallurgy of Lead and Desilverization of Base Bullion"; was published in 1893; the fifth edition in 1898. In 1913, he published his work on "General Metallurgy;" this was followed by "Metallurgy of Copper" in 1914, and a revised and enlarged edition of the "Metallurgy of Lead" in 1918. "Metallurgy of Zinc and Cadmium" is now in press. He also published, through the Massachusetts Institute of Technology, "An Outline of the Metallurgy of Iron and Steel" for students' use. Since the founding of "Mineral Industry" in 1892, he has been continuously the annual contributor on the metallurgy of lead, and all Institute members know that his contributions to the TRANSACTIONS have been liberal in the extreme. It is through this medium that the results of the extensive research work, which he has always carried on in connection with his work at the Massachusetts Institute of Technology, have been published. Of the greatest importance are his papers dealing with the formation temperatures of slags, but many other metallurgical subjects have been covered.

Jan 1, 1921

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the U.S. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and airways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof became the previous equilibrium is upset, resulting in pressures that cause fractures and slight, movements that are, frequently, hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned, the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 20 ft or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal bed, but this is rare. Impossibility of supporting the main roof and all of the cover

Jan 1, 1973

By R. G. Hudson, L. Yang

In electrochemical separation of metals, it is necessary to control the potential applied between the electrodes so that only the desired electrode reactions can occur. A knowledge of the minimum potential needed for a given electrode reaction to take place continuously is therefore pertinent to the success of the process. In molten chloride systems at high temperatures, activation polarization is believed to be small,1,2 so the minimum potential needed for the electrolytic decomposition of a molten metal chloride MC1n (n = valence of the metal ion) is therefore essentially the equilibrium electrode potential E of the metal-chlorine galvanic cell in the solution. If the decomposition products are pure M and chlorine at a pressure of p atm, E*Eo-rt/nf in [i] Since EO (the standard electrode potential of MCln) is a constant at a given temperature and R (the gas constant), and F (the Faraday's constant) are all constants, the variation of E with the electrolytic bath conditions is largely determined by the effect of the latter on the activity of the metal chloride amcln (standard state = pure MC1,). Measurement of E and study of how amCin varies with temperature and concentration, the nature of the solvent, and that of the coexisting solutes are therefore pertinent in the selection of optimum operating conditions for the electrochemical separation of metals. Because of its low melting point, high decomposition potentials of its components, and the low solubility of heavier metals in it, the LiC1-KC1 eutectic melt is a useful solvent and has been used in the electrodeposition of Mo,3Ce,4 and u5 metals. Senderoff and Brenner3 measured the potentials of Zn/Zn++, Fe/Fe++, Cu/Cu+, Mo/Mo+++, and Ag/Ag+ against an Ag/AgCl (pure) reference electrode at 600°C and a concentration of 4.1 mole pct of each chloride and came to the conclusion that complex ion formation occurred in some of the melts. Laitinen and LiUe gave an electromotive force series at 450°C for a number of {Metal/Metal ions (unit activity)) electrodes in LiC1-KC1 eutectic melt, the {pt/pt++ (unit activity)) electrode being chosen as the reference. Walker and Danly7 studied the ther-modynamic properties of NiC12 in LiC1-KC1 eutectic melt over a wide range of temperatures and concentrations by measuring the electrode potential between a nickel electrode and a chlorine electrode in the melt. Since potential measurements made by using the chlorine reference electrode are of more direct significance both in the study of electrochemical separation and in the evaluation of the thermodynamic properties of the melt, it is therefore decided to measure the electrode potentials of cells of the type {M/MCin (mole fraction = N) in LiC1-KC1 eutectic melt/Cl2 over a range of N values and temperature for a number of metal chlorides. The results should indicate the order by which the various metals plate out on the cathode and how this order is affected by temperature and the concentration of the metal chloride in the solu-

Jan 1, 1960

By G. D. TRANT

HOT metal is commonly transported from the blast furnace to the open hearth by one or the other of two general methods: (1) by hot-metal ladles, usually in conjunction with a stationary mixer, or; (2) by means of mixer-type ladle cars, taking the place of both the hot-metal ladles and the stationary mixer. In both cases, the use of transfer ladles for charging the metal into the open-hearth furnaces is necessary. The American Rolling Mill Co. at its Middletown division, adopted hot metal practice on. June 2, 1928. The pig iron is produced' in a .blast furnace about 11 miles from the open-hearth furnaces, and is trans- ported in Pugh-type mixer cars having a capacity of 150 gross tons each. Three cars are in service and handle the delivery of hot metal to the pig machine and the open-hearth furnaces. The capacity of the blast furnace is 550 tons and casts are made every four hours.

Jan 1, 1929

By Emmanuel P. Papadakis

Ultrasonic velocity measurements have been made to study the preferred orientation in cube-textured copper. Methods applicable to thin specimens were employed since the specimens were necessarily of sheet material. The measured velocities in various directions in the sheet differed from the corresponding values in single-crystal copper by 1 to 6 pet. The distribution of the deviations indicated that the align-ment of the (001) planes with the rolling plane was better than the alignment of the [100]and [010] directions with the rolling and transverse directions. Ultrasonic pole figures (velocity us orientation) are shown to be useful in the study of preferred orientation. THIS paper describes one set of experiments in a continuing study of preferred orientation in worked metals. This study has been undertaken to investigate the fundamental properties of metals when used as propagation media for ultrasonic waves. Many such materials are of current or potential use in ultrasonic delay lines. Fundamental studies on ultrasonic propagation parameters such as velocity, attenuation, and diffraction (beam spreading) are of importance in the design of delay lines, in the development of nondestructive testing methods, and in the study of materials themselves. Preferred orientation in worked poly-crystalline metals influences all three above-mentioned parameters, and hence is of particular importance. When polycrystalline metals are subjected to mechanical working, they develop textures dependent upon their crystal structure and the symmetry of the working operation.' The texture consists in the alignment of the crystallographic axes of the grains in preferred directions with respect to the symmetry axes of the working operation. Since the grains are elastically anisotropic, the elastic moduli of worked metals are anisotropic. Hence the velocities of elastic waves in worked metals depend on the directions of propagation and polarization. The worked metal may be thought of as taking on the elastic symmetry of a single crystal: so it possesses the same number of independent elastic moduli as the crystal class it simulates. In general, a worked metal does not adopt the crystalline symmetry of its own grains. For instance, most rolled sheet becomes effectively orthorhombic while all bar stock and wire develop hexagonal symmetry. However, certain metals with cubic crystal structure develop a cube texture upon rolling and annealing.= Nearly perfect alignment of [100]-type directions with the rolling direction, transverse direction, and rolling-plane norma1 can be achieved in certain fcc metals and alloys. These cube-textured rolled metals provide an excellent opportunity to test preferred orientation by means of elastic waves, since a worked metal with 100 pct cube texture would have elastic moduli identical to the moduli of its constituent metal. It is the purpose of this paper to present the results of an investigation upon cube-textured copper. Ultrasonic waves were used. The methods of measurement and the experimental results on the effective moduli will be given. The ultrasonic measurements will be shown to complement X-ray pole figures for the determination of preferred orientation in worked metals. EXPERIMENT To study cube - textured material, it was necessary to use thin-sheet material since a severe reduction in gage (95 to 99 pct) is necessary to produce cube texture. Special ultrasonic methods were needed to investigate the thin material at megacycle frequencies. A) Materials. The cube-textured material tested was a copper alloy containing 1 pct Zn. Specimens already measured for Young's modulus4 by Alers were kindly supplied by him. The specimens were slabs 3.00 by 0.25 in. cut from sheet 0.047 in. thick. The orientations of the long axes of the specimens with respect to the rolling direction were taken in 15-deg steps from 0 to 90 deg. B) Measurements. Two distinct experiments were performed to measure the phase velocity in these specimens. One measured the shear wave velocity for propagation in the 0.25-in. direction and polarization in the 3.00-in. direction. The other measured the velocity of both shear and longitudinal waves propagating in the thickness direction in the sheet. 1) Plate-Mode Measurements. The velocity of the zeroth-order shear mode5 was measured in the 0.25-in. direction in each strip. The specimens were ground thinner over half their length to assure that the first-order shear mode would be cut off below 6 Mc per sec, leaving the zeroth-order nondispersive shear mode as the only propagating mode. Piezoelectric ceramic transducers of 5 Mc per sec resonant frequency poled in their long direction were solder-bonded to the edges of the thin part of the slabs as in Fig. 1 after these edges had been made flat and parallel by fine grinding. These transducers produced waves polarized in the 3.00-in. direction and propa-

Jan 1, 1967

On the following pages are abstracts of papers published by the Institute during the year 1931 as Technical Publications, Preprints, and in bound volumes. For abstracts of papers that appear in bound volumes in 1931 but that were published as Technical Publications in 1930, see the Transactions, 1930. Papers that appear in the volume in which this list is printed are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 616. The abstracts are grouped as follows: Page Page Metal Mining....................... 578 ing and Metallography of Non-Milling and Concentration........... 578 ferrous Alloys)................586 IronandSteel...................... 580 Coal Division.. ................ 592 Petroleum and Gas.............. 598 Mctallurgy......................... 585 .............. 613 Institute of Metals Division (Found- Geophysical Prospecting......... 613 Metal Mining Use of Models for the Study of Mining Problems. By Philip B. Bucky. (Tech. Pub. No. 425, 12,000 words.)—This paper describes a research project undertaken to provide a means of studying the behavior of weighty structures such as mines, dams, foundations, etc., with models of the same material in the laboratory. The paper shows that in general it can be done. The underlying theory is explained, the apparatus which was developed and built to do this is described, and the results of laboratory experiments with sandstone mine structures are given. There is discussion of the accuracy of results with the present equipment, the model size necessary, and of the size and type of equipment necessary for the obtaining of results of practical value in the field. Milling and Concentration Ball Mill Studies, I. By A. W. Fahrenwald and Harold E. Lee. (Tech. Pub. No. 375. 25,000 words.)—This paper presents the results of an extensive experimental study of some of the numerous elements entering into ball mill grinding. All apparatus used was equipped with ball bearings. Every experiment was accompanied by a power measurement accurate to 0.005 hp. Quartz was used. Each element studied, such as ball load, was varied systematically. Power curves were obtained for the mill for three general sets of conditions; namely, (1) balls only (2) balls and quartz and (3) balls, quartz and water. For each general condition, power curves were obtained for various mill speeds, ball loads and ball sizes. For conditions 2 and 3, feed sizc and weight and pulp dilution also were studied as variables. The mill output, in grams of finished product per unit of time, was obtained for each test. In a general way, output (mill capacity) paralleled the power data and this attached

Jan 1, 1931

By Jonathan S. Jackson, Bayne B. McMillan, W. Joseph Schlitt

Various dump leach models have been developed by Kennecott, and these are reviewed with an eye toward production forecasting. Some of the models have been bated on first principles, utilizing the chemistry and physics of dump leaching. While providing considerable insight into the leaching process, these have proved to be too cumbersome for use in estimating production. Other models have been based on a declining leach rate for a single block of waste. These permit good short-term projections of solution grades and production, but are inflexible with regard to changes in mining parameters because the trends are based only on historical data. Therefore, a simple and flexible computer model has been developed to aid in leach production forecasting and to provide a tool for assessing the impact of different mining plans on leaching. This program, LEACH, is based on annualized blocks of waste; input parameters are described and examples of its use are given.

Jan 1, 1980

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

The Colorado School of Mines, Golden, Colo. M F Coolbaugh, President. Since 1906 the School of Mines has issued a journal, known as the Quarterly of the Colorado School of Mines, which carries many articles on matters of general interest as well as other articles of a technical nature There is no regular subscription price to the School of Mines publications Anyone interested in back numbers should write and find out the conditions under which individual copies may be obtained, whether a price is set on them or whether they are free Some back numbers are not now available but efforts will be made to supply copies from the files of alumni or other friends of the School Vol 23, No. 3 of the Quarterly (July, 1928) is an index of the publications complete from July, 1906 to July, 1928. A selected list of the technical articles appearing in the Quarterly is given here: Vol 3, No. 3, Rare metals. uranium and vanadium, by H. Fleck (1909), vol 3, No 4, Tungsten in Colorado, by H R Van Wagenen, vol 4, No 3, Preliminary report of the radioactivity of the carnotite of southwest Colorado, by H Fleck and W. G Haldane (1909), vol. 8, No 1 (1913), Some recent developments at Leadville, by G. M Butler, vol 8, No. 3, Physiography of

Jan 1, 1933