Search Documents

By F. C. Langenberg, J. Chipman

New data on the distribution of silicon between slag and carbon-saturated iron at 1600oand 1700oC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1700°C for slags containing up to 20 pct Al2O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A1203-SiO2 slags over a range from zero pct A12O3 to saturation with A12O3, or CaO.2A12O3. The upper limit of SiO, is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently, 4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/A12O3 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al2O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al2O3 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al,O3 and of A120,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO, (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2 The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

WASHINGTON, D. C. HERBERT C. HOOVER, Chairman H: FOSTER BAIN, Vice-chairman DAVID WHITE, Vice-chairman HARVEY S. MUDD, Secretary-Treasurer, Room 2114, Dept. of Interior Bldg. J. F. CALLBREATH HENNEN JENNINGS E. W. PARKER T. T. READ An inspiring meeting of the Washington, D. C., Section was held at the Cafeteria of the Interior Building on Friday evening, Dec. 6, 1918. One-hundred and thirty-five members and guests attended, and Vice-chairman H. Foster Bain presided. The Committee on Nominations reported: for Chairman, Herbert Hoover; for Vice-chairmen, Frederick G. Cottrell, and F. L. Ransome;

Jan 1, 1919

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

James Douglas will long be remembered as a distinguished mining engineer and metallurgist, as a scientist with broad vision, as an executive whose understanding of practical problems coupled with his knowledge of men and affairs enabled him to weld together great mining interests and to their service build railroads and bring power. More, he will be recalled as a philosopher and a writer of charm, a historian of no mean order, and one whose catholic tastes and enthusiasms led him into the fields of education, medicine and theology. His aim was to possess that which he considered made life worth while—friends and effectiveness in whatever task he undertook. In this aim he was successful to a degree exceeded by few, as thousands of his friends and associates could and can testify. Dr. Douglas was born on November 4,1837, at Quebec, Canada. His father, James Douglas, Sr., was a prominent physician and the leading surgeon of Canada. He also established the first retreat for the insane in the Dominion, the Quebec Lunatic Asylum, to which he devoted his services for years; The son followed in the footsteps of his father and studied medicine, not only in Canada but also in Scotland and in Germany. He entered the University of Edinburgh in 1855 but after two years at that institution returned to Canada and was graduated from Queens university at Kingston, Ontario, .with the degree of Bachelor of Arts. Later he went to Lava1 University, Quebec, and subsequently became professor of chemistry at Morrin College, Quebec. After he was graduated—at the time he considered his formal education completed—he traveled with his father in Europe and in the Orient; visiting Egypt, being especially interested in that country, several times. They gathered together an important archaeological collection which later was donated by them to the Metropolitan Museum of Art in the city of New York. James Douglas was also greatly interested in photography, a hobby in which he made use of his chemical knowledge. The writer can remember distinctly the descriptions he gave more than forty years ago in Arizona of the difficulties he encountered with the old wet photographic plates, especially while traveling in Egypt, when he prepared and used his own chemicals. In his humorous manner he told how he once discovered, in the nick of time, the nurse preparing to give the baby in the party a rub-down, using for that purpose the white, limpid

Jan 1, 1934

By Robert H. Richards, E. E. Bugbee

Friends often ask how accurate the work of our little stamp mill is, or express the opinion that a little mill cannot do good work. As a reply we would like to place on record the results of a few tests. There are two periods of work in our laboratory; the fall term, when the class collectively goes through all our chief laboratory-processes, and the spring term, when the students work up their theses, each electing some one process or investigation and devoting himself wholly, or almost wholly, to that. Some of the tests, the results of which are recorded in this paper, were made in the fall term; the preparation of the apparatus, the sampling and the assaying being done largely by assistants, with the aid of the students. Others were made in the spring term as thesis-work, and the results are due wholly to. the students. The complete " tree " of our process is patterned after the-

Jan 1, 1904

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950's the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

PUGET SOUND SECTION SIMON H. ASH, Chairman, I. F. LAUCKS, Vice-Chairman, CHARLES SIMENSTAD, Sec.-Treas., 425 Lyon Building, Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT. The Puget Sound Section met at the Arctic Club, Oct. 28, 1916, for the annual meeting. Those present were: Chairman Glenville A. Collins, Vice-Chairman H. L. Manley, Sec.-Treas. Amos Slater, Chester F. Lee, R. P. Tarr, G. E. Rockefeller, Simon Ash, Geo. W. Evans, Joseph Daniels, I. F. Laucks, F. C. Greene, Darsie C. Bard, Marcel Daly, Milnor Roberts, F. A. Hill, Percy E. Wright, and as guest, Mr. Coates of British Columbia. After dinner had been served, Chairman Collins called the meeting to order. The reading of the minutes of the last meeting were suspended upon request of the Secretary. The Secretary read the report from the Committee on the Associated Engineering Societies of Seattle. Upon motion, duly seconded, the report was adopted and placed on file. Mr. Lee, Chairman of the Committee. on the Mining Men's Convention to be held this coming winter, gave his report orally, and upon motion the committee was continued. The report of the Secretary-Treasurer was read, received, and placed on file.

Jan 3, 1917

OIL FLOTATION DISCUSSED BY SOUTHERN CALIFORNIA SECTION . A meeting of the Section was held in the home of R. H. Norton, 335 W. 27th Street, on Mar. 10, thirty-two members and five guests being present. Vice-chairman Staunton opened the meeting with a description of an experiment he made with oil flotation, and then introduced the guest and speaker of the evening, L. C. Penhoel, of the South-western Engineering Co., who gave a very interesting and informal talk on the subject of Flotation. During the talk, as points were raised, there was a general discussion, in which valuable information was brought out. A number of examples of successful competitive, results by cyanidation and flotation in large milling plants in this country and Mexico were cited and discussed. The latter part of the meeting was devoted to a discussion of the bill introduced in the California State Senate, to license and register engineers. Mr. Ernest Strout gave a most favorable opinion of the principal of licensing mining engineers from his extensive experience in the working out of such a law on the Rand. All members who spoke were opposed to this bill as drafted but felt that the subject was of too great importance to the profession to attempt to amend the present bill in the week or two that remains, and that the passage of a bill that was so crude and inefficient for the achievement of the results desired, would harm the engineering profession. After the meeting adjourned a short time was spent in social intercourse, during which light refreshments were served. The appreciation and thanks of the Section is extended to Mr. and Mrs. R. H. Norton for their hospitality. ALVIN B. CARPENTER, Secretary-Treasurer.

Jan 5, 1919

Kaiser Sees Bright Future for Jamaica Kaiser Aluminum Co. has a big stake in the British West Indies, the Island of Jamaica in particular. There, Kaiser is busy developing one of the most promising bauxite finds in recent years. The $12 million operation was officially opened in February. Facilities have a rating of an annual capacity of 2 million tons and will supply Kaiser plants with ore for years. The ore comes across the Gulf of Mexico, up the Mississippi to stockpiles at Baton Rouge. The stockpile at Baton Rouge would throw many an old river boat skipper for a loss. Where no mountain once existed now stands a man-made bluff of bauxite, known as Bauxite Peak.

Jan 6, 1953

PENNSYLVANIA ANTHRACITE LOCAL SECTION On Saturday evening, Jan. 31, 1914, about 40 members of the Institute met at the Hotel Sterling, Wilkes Barre, Pa., for the purpose of discussing plans for the formation of a local section in the Pennsylvania anthracite region. President Rand; Prof. Joseph W. Richards, of the Board of Directors; Dr. H. M. Chance, Chairman of the Committee on Coal and Coke, and Secretary Stoughton were among the guests present. R. V. Norris acted as Master of Ceremonies, and the arrangements were all made in advance by a Committee under the leadership of Charles Enzian, to whom an enthusiastic vote of thanks was accorded at the dinner. An address was made by President Rand, followed by .Professor Richards, who outlined the procedure necessary for the formation of a Local Section. Addresses were then made by W. J. Richards, F. W. Chase,. C. F. Huber, R. J. Foster, F. A. Hill, H. M. Chance, Bradley Stoughton, and others, after which a rising vote was taken, and it was unanimously decided to petition the Board of. Directors for the establishment of the Pennsylvania -Anthracite Local Section. More than the required number of members then signed -the petition, and President Rand announced the appointment of a Committee to organize the Section and arrange for a meeting in accordance with their By-Laws, consisting of R. V. Norris, W. J. Richards, R. J. Foster, Edwin Ludlow, C. F. Huber, Charles Enzian, Douglas Bunting, F. A. Hill, and J. M. Humphrey.

Jan 2, 1914

BOSTON SECTION R. L. AGASSIZ, Chairman, - JAMES G. CARLETON, Vice-Chairman, E. E. BUGBEE, Sec.-Treas., Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS, G. A. PACKARD. The forty-fifth meeting of the Boston Section was held, at the Engineers' Club, on Tuesday, Nov. 6, 1917. Mr. F. C. Carstarphen, tramway engineer of the American Steel and Wire Co., was the guest of the evening. After dinner, Mr. Carstarphen gave a most interesting illustrated talk on the subject of aerial tramways. The views-showed the various forms of aerial tramways and three' unique installations, one carrying 285 tons of coal an hour, undoubtedly the maximum quantity transported by any tramway up to this time. The second installation is that of a lumber-carrying tramway, 5 miles long, operating in California. The last views illustrated a 13 ½ -mile tramway for carrying salt over the

Jan 2, 1918

Plans have been completed with only details to be arranged for the first Metals Branch Conference in the Northwest. The two day meeting will be held jointly with the Industrial Minerals Div. on Friday and Saturday, May 9 and 10, 1952, at the Davenport Hotel in Spokane, Wash. For, some time the metals activities in this area have been neglected. Expansion of metal producing and fabricating industries in Washington and neighboring states has brought sufficient interest to insure the success of such a meeting. A committee has been hard at work for several months. Nonferrous extractive metallurgy men will find an extensive program in the April issue of JOURNAL OF METALS. Sessions for iron and steel producers, physical metallurgists, and educators will make the Metals Branch picture complete. Metals Branch members residing in Washington, British Columbia, Oregon, Idaho, Montana, Wyoming, Nevada, and Utah, or who can be in the Northwest at this time should make plans now to attend. A Metals Branch luncheon is planned for Friday and a dinner jointly with the Industrial Minerals Div. is planned for Saturday according to F. R. Morral, metallurgist with the metallurgical research div. of Kaiser Aluminum & Chemical Corp., P. O. Box 1451, Spokane, Wash.

Jan 1, 1952

BOSTON SECTION ALFRED C. LANE, Chairman, GEORGE A. PACKARD, Vice-chairman, E. E. BUGBEE, Sec'y-Treas., Mass. Inst. of Technology, Cambridge, Mass. R. L. AGASSIZ, FRED W. DENTON. Forty-sixth Meeting The forty-sixth meeting of the Boston section was held at the University Club on Monday evening, Jan. 28, 1918. Thirty-six members and guests were present, which is a record for this Section. After a good dinner, President Philip N. Moore, of the Institute, was introduced, and spoke of the many problems of the Institute. The topics covered were the progress and growth of the Institute during the administrative year, the efforts to stimulate the local sections and to bring them more in touch with the policies and problems of the parent body and, last but not least, of the constructive results and patriotic work of the Institute in the national service of the war. The other guest of the Section, Mr. Thomas Nelson Perkins, Counsel for the Priority Board, spoke most entertainingly of recent experiences in Russia, England and France. After considerable discussion during which Mr. Perkins most obligingly answered innumerable questions, the meeting adjourned at about 10 p. m.

Jan 7, 1918

The thirty-ninth meeting of the Boston Section was held at the Engi- neers? Club on Monday evening, Dec. 4, 1916. Thirty-three members and guests sat down to dinner; There were present as section guests; Dr. L. D. Ricketts, and Prof. Bradley Stoughton, President and Secretary of the parent society, and each was called upon to speak. Mr. Stoughton spoke of the growth of the Institute during the past year and described the very numerous and important activities, of which the junction of the American Society of Civil Engineers with the other three societies is perhaps the most important. Dr. Ricketts, the advertised speaker of the evening, spoke on Recent Progress in Mining and Metallurgy of Copper Ores. In discussing the improvements in mining, he traced the mining methods from square- set mining to the modified Ohio System now so successfully used at Inspiration: In metallurgy, he described the growth of reverberatory-smelting ant1 allied problems such as the utilization of the waste heat for generating steam. He laid stress on the importance of sampling and bedding of

Jan 6, 1917

The selection of a particular machine for production drilling is the most critical drill evaluation the pit engineer is called upon to make. It is a true engineering design problem requiring value judgments. Generally, the procedure follows these steps: (1) Determine and specify the conditions under which the machine will be used, including such service factors as labor, site, weather, etc. (2) State the objectives for the rock-breakage phases of the production cycle of operations--considering excavation and haulage restrictions, crushing capacity, production quota, and pit geometry-in terms of tonnage, fragmentation, throw, etc. (3) On the basis of blasting requirements, design the drill-hole pattern (hole size and depth, in- clination, burden, spacing, etc.) (4) Determine the drillability factors and select the drilling methods which appear feasible for the kind of rock anticipated. (5) Specify the operating variables for each system under study, considering drill, rod, bit and circulation fluid factors. (6) Estimate and compare performance parameters, including costs. Major cost items are bits, drill depreciation, labor, maintenance, power and fluids. (7) Select the drilling system that best satisfies all requirements with the lowest over-all cost.

Jan 10, 1967

SAN FRANCISCO SECTION W. H. SHOCKLEY, Chairman, PRANK H. PROBERT, Vice-Chairman, T. A. RICHARD, Sec.-Treas., 420 Market St., San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. The San Francisco Section met on September 11 to discuss the problem of Labor in its Relation to the Mining Engineer. Mr. W. H. Shockley was in the chair. T. A. Rickard opened the discussion under four heads: The recognition of the union, the rustling-card, the sliding scale of wages, and the' contract system. He expressed his belief that collective bargaining cannot be ignored, and insisted that the mining company represented a collective bargaining of its shareholders with the men. employed in its mine. He held that the contract system was often used unfairly, but that used fairly it was the best check on labor tyranny. The rustling-card he held to be right in principle, in so far as it gave the employer the choice of employees, but he believed that it was often used in an irritating way to black-list refractory laborers. The sliding scale of wages was easy to establish in prosperous times, but it would inevitably lead to trouble when conditions went against the miner. His conclusion was that the quarrels of labor and capital were due mainly to a lack of the sense of fair play and of social justice. Albert Burch agreed with most of the foregoing, and insisted that 90 per cent. of the men were inclined to be just, but that the 10 per cent: made all the trouble. He stated that he had introduced the rustling-card in the Coeur d'Alene in 1899, as a means for getting rid of agitators. E. L. Foucar considered that labor was irresponsible. He described his experience in Peru, where the authorities promptly stopped a strike of Italian miners by threatening prompt punishment for any display of violence. Morton Webber also gave a bit of his own experience, to show that the chief trouble is that the men do not think for themselves, and are therefore easily led by fomenters of trouble. F. H. Probert described his experiences in Germany and. also in Arizona, and insisted that too often the men were not given a fair hearing. E. T. Blake argued that a manager must get the workmen's point of view, in order to control them effectively. He believed that young men who started life doing manual labor were in a better position to understand their fellow workers. George J. Young suggested that the mine owners should encourage the good men to lead the unions, and not leave the direction of the unions to the noisy element.

Jan 12, 1917

THE RELATION OF THE ENGINEER TO RECONSTRUCTION FIFTY-THIRD MEETING OF BOSTON SECTION The fifty-third meeting of the. Boston Section was held April 28. The speaker of the evening was the new president of the Institute, Mr. Howard V. Winchell, who spoke on "The Relation of the Engineer to Reconstruction." He told of the part engineers had played in the war and paid tribute to Herbert E. Hoover as an example of what engineers can do. He said that engineers are not taking enough interest in politics, although it is badly needed as shown by the evidences of Bolshevism even in America. Conditions have suddenly changed; whereas we formerly borrowed money we are now loaning widely to foreign countries and our investments, abroad have to be protected. A committee is badly needed to investigate and determine the actual conditions. The Government has already been invited to cooperate with the Institute along professional lines and this should lead to closer contact between our Society and the Government. Mr. Winchell then went on to describe some of the mining conditions in Russia. He brought out the point that the rich platinum deposits are exhausted and only the poorer sands remain. The largest copper properties average less than 2 per cent. copper and there are some 4,000,000 tons available in .the Caucasus region near Batum. There are approximately 100,000,000 tons of high-grade manganese ore scattered in small deposits in the eastern Ukraine. There are some copper mines in the East, butt they are almost exhausted. The Baku oil field is the second largest in the world and there is probably oil in Persia. There are also manganese in Siberia and coal veins of enormous thickness.

Jan 7, 1919

BOSTON LOCAL SECTION Executive Committee HENRY L. SMYTH, Chairman ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS ALBERT SAUVEUR Meets on the first Monday evening of each winter month, Twenty-third Meeting The Twenty-third Meeting of the Boston Local Section was held at the Engineers' Club, 2 Commonwealth Ave., on Monday evening, Nov. 30,- 1914. Prof. R. A. Daly addressed the meeting on The Iron Ores of Küruna; Sweden. AUGUSTUS H. EUSTIS Secretary.

Jan 1, 1915

By R. E. Allen, A. C. Jephson

ELECTROLYTIC zinc plants of the American Smelting and Refining Co. are located adjacent to the present city limits of Corpus Christi, Texas. The original plant commenced operations during 1942, and is designed for the production of special high grade zinc from zinc sulfide concentrates.' Subsequent changes include the erection of an additional acid plant during 1950, and additions for increased generating and production capacity during 1951. New Electrolytic Plant—The new electrolytic plant is a separate unit erected for the treatment of densified fume produced at Asarco plants located in El Paso, Texas and Chihuahua, Mexico. Construction was completed and operation commenced during June, 1953. Decision for the erection of a separate plant for the treatment of densified fume is based on several factors. One of the principal reasons is the assurance of continued production rate of the original plant, which might have been jeopardized by combined treatment of calcine and fume. Of equal importance is the advantage of locating a plant on a site with adequate space for eventual expansion. General Description—The new plant for the treatment of densified fume consists of four main buildings for the following operations: storage and grinding of fume, leaching and purification, electrolyzing and casting, and rectifier units. Auxiliary buildings include a baghouse, reagent storage, and a lunch room. Leaching of ground fume with electrolyte from the cells is a batch type operation in tanks equipped with mechanical agitators and weightometers. Completed leaches are pressure filtered, the resultant residue being recovered for shipment to El Paso by conventional use of thickeners, drum type vacuum filters, and a direct-fired dryer. Filtrates from the filter section are purified in mechanically agitated tanks, filtered after completion through plate and frame presses, and then pumped to an evaporative type cooling tower. Solution discharged from the basin of the cooling tower is collected in storage tanks for use in the cells. The cool purified solutions are pumped as required from storage to the solution circuit for circulation of electrolyte through the cells. Except for the addition of purified feed solution and withdrawal of electrolyte for leaching, the circulating system for the cells is essentially a closed continuous circuit that includes the use of evaporative cooling towers for control of solution temperatures. Aluminum cathodes and Ag-Pb anodes are used for electrolysis, which is maintained at a current density of about 82 amp per sq ft. Cathode zinc produced is melted in a gas-fired reverberatory furnace and then cast into slabs on a straight line casting machine. Unloading and Storage—Fume produced by the Chihuahua plant is shipped in box cars, and fume by the El Paso plant in hopper bottom dump cars. Shipments as received are weighed on a 7 5-ton capacity railroad scale, sampled, and then moved over one of the two unloading hoppers with a car puller. The cars are then unloaded with mechanized equipment, a car scoop being used for unloading of box cars and a car shaker for the hopper bottom cars

Jan 1, 1958