Search Documents

By A. R. Gregory, A. L. Podio, K. E. Gray

Dynamic elastic properties of dry and water-saturated Green River shale samples were computed from compressional- and shear-wave velocity measurements. P- and 5-wave velocity measurements were made in three mutually perpendicular directions with respect to the bedding planes. Measurements were also made in several different directions by varying the angle between the bedding planes and the direction of propagation of the wave for angles of 0, 30, 45, 60 and 909 The oriented samples were subjected to both confining pressure and axial loads, in excess of the confining stress, in the direction of propagation. In general, P- and S-wave velocities increased with increasing stress levels, with a corresponding increase in Young's modulus. Water saturation caused the P-wave velocity to increase and the S-wave velocity to decrease. Elastic moduli decreased upon saturation, except for Pois son's ratio, which increased, indicating some degree of weakening of the material. The samples showed a moderate degree of anisotropy; this was to be expected from the laminated nature and shallow occurrence of Green River shale. INTRODUCTION This paper presents some results of an experimental determination of the elastic coefficients of anisotropic materials (in particular, finely layered rocks and minerals such as Green River shale) from measurements of dilatational and shear-ultrasonic-wave velocities. Ultrasonic techniques have been used extensively in nondestructive testing. Several methods have been proposed by Mcskimmin, 1 and some of these have been used successfully to measure ultrasonic velocities in rocks. Hughes and Cross, 2 Wyllie et al., 3 and Birch 4,5 developed pulse first-arrival techniques for the measurement of dilatational and shear velocities. Williams and Lamb 6 used the method of cancellation of a traveling wave, which was later modified by Myers et al.' and perfected by McSkimmin. 8 Although this method is highly accurate, it has not been used as widely as the pulse-transmission methods recently reported by Jamieson and Hoskins 9 King,10 and Mattaboni and Schreiber. 11 It has been common practice to use some form of crystal transducers, either quartz or ceramic, that has been cut or polarized in different directions in order to generate either compressional or shear waves. However, accurate determination of shear wave velocities has been difficult due to problems that arise in obtaining a pure shear wave from cross-polarized crystals, which usually also generate a small amount of compressional energy. As reported by Gregory, 12 this energy can be seen as a long precursor preceding the sharp break of the shear first arrival. The need for generating pure shear waves led to interest in mode-conversion techniques, which are based upon conversion of the mode of vibration through wave reflection or refraction at a discontinuity. Arenberg13 showed that for certain materials and for certain angles of incidence it is possible to generate pure shear modes by reflection at a boundary. Jamieson and Hoskins 9 used a pyrex glass-air interface for generating pure shear waves, and King 10 used this method successfully for measuring shear-wave velocities in rocks. Gregory l4 arrived at a similar result by refraction of a wave at an aluminum-oil interface. A plane compressional wave, traveling in the oil phase, is incident on the aluminum at an angle larger than the critical angle for compressional waves, and thereby generates a purely transverse, plane-polarized wave in the aluminum. During the last few years methods have been developed that allow the simultaneous determination of shear and compressional velocities in solids.

Jan 1, 1969

By J. B. Tyrell

A SHORT time ago I paid a visit to the alluvial gold fields on the tributaries of the Chaudière River in Beauce County, Quebec, in company with A. 0. Dufresne, late manager of the Champs d'Or Rigaud-Veaudreuil, and now Assistant to the Superintendent of Mines of the Province of Quebec. As the conditions under which the gold occurs in this district are not very generally known, and present some interesting features, a brief description of these conditions, and a consideration of the causes which gave rise to them, may be of interest to other mining engineers. During the latter half of last century the country was visited by many mining engineers and geologists, and many references to it may be found in the reports of the Geological Survey of Canada between 1848 and 1911. The most important of these are by J. A. Dresser and J. Keele and the late Robert Chalmers. The Department of Colonization and Mines of the Province of Quebec also published a report with map on the district by J. Obalski. From the earliest times the valley of the Chaudière River formed one of the main avenues of approach to the St. Lawrence in the vicinity of Quebec from the country to the south as far as the seaboard of the States of Maine and Massachusetts. The Indians had a well-known trail along the banks of the stream, and armed troops and foraging parties constantly moved backward and forward along it between Quebec and New England in those insecure times before the ceding of Canada to Great Britain. Even yet the natural advantages of this old military route are recognized, and the government of the -Province of Quebec has now under construction along it a magnificent highway from Quebec to the International Boundary Line, which is to form part of a through highway from that city to Boston; The land along the valley is naturally well suited for agriculture, and about the end of the eighteenth and the beginning of the nineteenth centuries farmers began to go back from the St. Lawrence, and to occupy the higher lands along the upper portions of the Chaudière Valley. This settlement has gone on until now the country is peopled with a prosperous agricultural population.

Jan 3, 1915

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945

By Frederick C. Hull, Robert F. Mehl, Robert A. Colton

IT is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.1,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in 1939.3 Two types of process were described: (1) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemi¬spheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. 1);2.4 the former, occurring near the knee of the S-curve has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ae1, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important 1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenability; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels.* PREVIOUS DATA ON RATE OF NUCLEATION AND RATE OF GROWTH Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Mehl,1 and by Dorn, De Garmo and Flanigan.2 It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given.

Jan 1, 1942

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By C. T. Holland

This discussion is concerned with those com-J- paratively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities." Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.' CAUSES OF ROCK BURSTS Rock bursts in coal mines have occurred in sev-eral places under diverse geological conditions, mining methods, and/or practices. A study of many such occurrences indicates that they depend on the following conditions: 1) cover thickness of 500 ft or more, 2) cover composed of strong members and having a strong member lying close to or on the coal bed, and 3) a floor that does not readily heave. The minimum thickness of cover under which coal mine rock bursts occur is based on observation. Under unusual circumstances involving very strong roof members and/or mining systems, and/or practices especially likely to induce bursts, a burst conceivably could occur under less roof. Under special circumstances rock bursts have occurred in marble quarries almost at the surface.' Furthermore, under very heavy cover it is likely that controlling roof members need not be as strong and as close to the coal bed to cause bumps. Just what constitutes a strong roof or roof member is open to question. Obviously the strength of a roof member is determined by its thickness, the distance between bedding planes across which little or no bond exists, the spacing and development of joints, and the inherent strength of the rock material. Strata sections showing roofs under which rock bursts in coal mines have developed are illustrated in Fig. 2. In several instances the strength of rocks composing the roof of mines developing bumps has been tested. The tests (Table I) show that these rocks develop considerable strength in compression, bending, and shear and that in some cases the strengths are very high. No quantitative data are available concerning joints in roof members over coal beds where rock bursts have occurred, but the author has examined many mines subject to bursts and has received the impression that joints in the shales immediately over the coal beds are always present and well developed. In the main sandstone or conglomerate members themselves, however, where observed, he has yet to see a fracture system indicating well developed joints. Undoubtedly joints are present, but the evidence indicates that they are few, poorly developed, and widely spaced. In a mine subject to bumps, moreover, actual measurements of roof spans up to 225 ft between supports under a cover of about 800 ft have been made before roof failure occurred. Such spans signify strong roof. In coal beds subject to rock bursts, the bottom rock is usually a sandy shale. A few tests (Table I) have been made on the floor rock of coal beds. Observations in mines indicate that they are usually weaker than roof rocks and that under load they show more plastic effects. Observation in ground subject to bursts invariably indicates a relatively strong floor highly resistant to heaving, although some heaving may occur. Other factors listed as favorable to rock bursts are: 1) mountainous surface; 2) steeply dipping beds; 3) proximity of faults, folds, and other similar geologic structures. Many bursts have occurred in mines under mountainous country, although many bursts in mines under a surface with little relief indicate that thickness of cover, not relief, is the essential factor. In steeply dipping beds, many bursts occur in mines that are essentially flat, and rock bursts have been recorded in beds dipping as much as 35o Most rock bursts in the U. S. occur in beds that dip less than 10 pct. It is also true that most U. S. coal is produced from beds dipping less than 10 pct. Geologically, faults are regarded as providing stress relief, but in the vicinity of faults, as well as sharp folds, it would seem that residual stresses could be present. The fact that rock bursts occur in areas remote from faults and sharp folds suggests that their presence is not necessary for this phenomenon to take place. There have been many bursts close to faults and folds, and it may be assumed that occasionally such structures accentuate their occurrence3 The conditions and circumstances under which they occur, coupled with the effects produced, leave In the Crowsnest Pass coalfield, British Columbia, a rock burst is estimated to have released 1.8 million cu ft of methane.

Jan 1, 1959

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of 'InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of' metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.'-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.' This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.' A concurrent publication'0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.'' Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By T. Egleston

FOR a great part of the progress of the world we are indebted to the works of engineers. It is to them that we owe our means of rapid transportation, our canals, our railroads, our bridges, many of our automatic machines, and most of those appliances which, by facili tating or decreasing the amount of human labor to be expended and by utilizing the great forces of nature, have made the present progress of the world possible. Their education is a matter of momentous interest to the whole civilized world. I have, therefore, thought that some discussion of the theory upon which their education should be based would be of interest to this body, and have ventured a few reflections and suggestions upon the subject. The word education, in its original signification, meant the draw ing out of a man what there was in him. In our common schools the practical work of education consists in putting into the brain a larger number of facts than can be retained, which are consequently more or less understood and digested. It ordinarily consists simply of teaching a round of abstractions or facts which when not assim ilated are not only useless to the individual, but generate careless habits of thought and make more or less untruthful, unfaithful or unsuccessful men. In most of our schools a procrustean system is adopted; all are made to advance upon one general plan, the quick being kept back and the slow dragged on at a rate too great for their power of comprehension. Until within a very few years it has been a theory in common school education that the brain alone should be developed, and that little or no attention need be paid to the train-

Jan 1, 1888

State of Louisiana, Department of Conservation, Division of Minerals, 126 New Orleans Court bldg , New Orleans, La. Dr. J. A Shaw, Director The Bureau of Scientific Research of the Minerals Division has recently issued the first of a proposed series of Geological Bulletins on the geology of Louisiana, by parishes The bulletin may be had for 25 cents postage by writing to the above address: Geological Bulletin 1, Geology of Iberia Parish (1931) Other bulletins of a more general nature have been published in the past. Bulletin 13, A brief survey of the natural resources of Louisiana (1930) (revised 1931), 14, The clays of the Shreveport area (1927), 16, The clays of Monroe area (1928), 19, The clays of Alexandria area (1929). The latest (Tenth) Biennial Report of the Department of Conservation for 1930-1931, containing a review of the natural resources of the state in the report of the Division of Minerals, may be obtained on payment of 25 cents for postage

Jan 1, 1933

By C. S. Finney, John Mitchell

The introduction of ovens for the production of metallurgical coke is believed to be due to L. L. Norton who operated an iron foundry in the vicinity of Connellsville, Pa. Persuaded by his foreman, an English immigrant named Nickols from Durham, L. L. Norton put up a 12-ft square oven which produced coke in 1833. The coal used was taken from a local mine at Mounts Creek. The oven seems to have been used in conjunction with the customary method of coking in mounds. It was in the Connellsville district also, in 1841, that two carpenters, Provence McCormick and James Campbell, formed a partnership with John Taylor, a stone mason, for the manufacture and sale of oven coke. The task of the mason was to construct the ovens, while the carpenters were to build the arks by which the coke could be taken by water to the market at Cincinnati. The following account of the enterprise was given by McCormick: "James Campbell and myself heard in some way that I do not now recollect that the manufacturing of coke might be made a good business. Mr. John Taylor, a stone mason, who owned the farm on which the Fayette coke works now stand, and who was mining coal in a small way, was spoken to regarding our enterprise, and proposed a partnership-he to build the ovens and make the coke and Mr. Campbell and myself to build a boat and take the coke to Cincinnati, where we heard there was a good demand. This was in 1841. Mr. Taylor built two ovens. I think they were about 10 feet in diameter. My recollection is that the charge was 80 bushels. The ovens were built in the same style as those now used, but had no iron ring at the top to prevent the brick from falling in when filling the oven with coal, nor had we any iron frames at the mouth where the coke was drawn. The top and mouth had to be repaired when they fell in. In the spring of 1842 enough coke had been made to fill two boats 90 feet long-about 800 bushels each-and we took them to Cincinnati down the Youghiogheny, Monongahela, and Ohio, but when we got there we could not sell. Mr. Campbell, who went with the boats, lay at the landing some two or three weeks, retailing out one boatload and part of the other in small lots at about 8 cents a bushel. Miles Greenwood, a foundryman of that city, offered to take the balance if he would take a small patent flour mill at $125.00 hi pay, which Mr. Campbell did. He had it shipped here. We tried it, but it was no good, and we sold it to a man in the mountains for $30.00, and thus ended our coke business." So successful did the coke subsequently prove to be in use that the three partners were asked to deliver more. Evidently they had had enough of the coke business, however, for they refused to have anything more to do with it. Few ovens were built between 1841 and 1855, and it is reported that in the latter year, "there were only 26 coke ovens along the river above Pittsburgh". Successful coke makers of these years included Mordecai Cochran, Richard Brookius, and Colonel A. M. Hill. It was the use of coke in 1859 in the Clinton furnace erected by Graff, Bennett and Co. in a plant on West Carson Street, Pittsburgh, that brought the real beginning of the coke-iron era in America. Here the successful use of Connellsville coke as a blast-furnace fuel was demonstrated beyond all possible doubt, and from the year 1859 the coking industry expanded tremendously. The era of beehive coke ovens During the latter half of the nineteenth century and the early years of the twentieth, the major percentage of metallurgical coke produced in the United States came from beehive ovens. It was not until 1893 that the first battery of by-product ovens came

Jan 1, 1961

By Ellis Clark

THE mining town of Pribram is situated in Central Bohemia, on the western slope of the Heiliger Berg, 30 miles southwest from Prague. Birkenberg, the village in which most of the shafts and ore-dressing establishments are situated, is built on a mountain of the same name. It is about a mile from Pribram, is 1700 feet above the sea, and is surrounded by graywacke rocks of Silurian origin, which are intersected by greenstone dikes, and in the southerly, southeasterly, and southwesterly direction are bounded by granite. The graywacke formations consist on one side of graywacke sandstone and quartzite, and on the other of graywacke slates. These last are separated from the first in the immediate vicinity of the mines by a graywacke seam converted into clay. For many years this so-cal led clay seam (lettenkkluft) was considered as a boundary of the ore deposits in both zones of graywacke. The graywacke formation is divided according to its hardness, structure, texture, and color, into fine, coarse, compact, slaty, whitish-gray, reddish-gray, and black graywacke. The, miner divides the formation into four divisions. The first or lowest division, which is in contact with the granite, consists of a fine-grained dirty gray slate; the -second is a very fine to a very coarse schist, white to reddish-gray in color, and rich in quartz, but containing little mica; the third consists of a slate with a contused cleavage, which has a dirty gray, dark gray, and very often black color and is often graphitic in its composition ; the fourth consists of a fine to coarse-grained graywacke schist, of a grayish-white or reddish-gray color, and rich in quartz. The cleavage in all four divisions strikes from northeast to southwest, and the dip is sometimes northwesterly, sometimes southerly, and often vertical. All four zones are cut through by a great number of diorite and greenstone dikes and chimneys. The thickness of these dikes, which are of

Jan 1, 1881

Jan 1, 1893

By Milnor Roberts

WAR struck the mineral industry of Washington with cross currents that produced a peculiar result. The State's production of coal, industrial minerals, and metals for 1941, valued at $28,507,282, was increased in 1942 under war pressure to approximately $35.000,000. Meanwhile a tremendous demand had arisen for men to construct airfields and many other large projects for the Army and Navy in Washington and Alaska, and Government plants for the mineral industry costing $140,000,000 or more, as well as a call for employees in the U. S. Navy Yard at Bremerton, the sixty shipyards, the four Boeing airplane factories with many auxiliary shops, and hundreds of other plants turning out war materials. In spite of an influx of nearly 300,000 people, causing an increase of 17.1 percent in the population since 1940, according to the Census Bureau, the State clearly is still engaged in an unusual amount of war production in proportion to its population. A large proportion of the workers have been drawn from the mineral industry to the war plants, whether through motives of patriotism, high wages, or, in the Boeing plants at least, the glamour of the operation

Jan 1, 1944

A new departure of unusual importance in Institute annals was in-augurated by the trip of President Philip N. Moore to the Local Sections at Nevada, Southern California, San Francisco, Seattle, Spokane, Montana, Utah, and Colorado. Everywhere the visit of the President was the occasion of an enthusiastic and successful meeting, which is reflected in the account, published under the different Sections in this and other Bulletins. The President also joined the members of the Columbia Section in their visit to Nelson, British Columbia, at the International Mining Convention, which was attended by mining engineers of Canada and the United States. The President of the Canadian Mining Institute, as well as the officers and members of the Western Section also attended this convention. For full particulars we recommend to our readers the ac- count of this very interesting meeting, which is given on another page of this. Bulletin. It is believed that this is the first meeting between the mining engineers of America and any other country since America joined the Allies. The Secretary of the Institute accompanied the President at the first four meetings and was expecting to attend the others also, but was called home by a death in his family.

Jan 7, 1917

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By AIME AIME

THE ninth International Petroleum Exposition held at Tulsa, May 16-23, broke all size, sales, and attendance records of previous shows. More than $12,500,000 worth of equipment was on the grounds. There were 546 companies exhibiting and every available inch of the fifteen acres allotted to exhibit was taken. Drake Drive, the main street of the exposition, was literally "supply row" with National Supply, Frick-Reid, Continental Supply, Oil Well, Bridgeport, International Derrick and Equipment, and Parkersburg Rig and Reel companies occupying the entire space. The exhibitors were a cross section of American industry, with such firms, besides the strictly oil equipment firms, as the United States Steel Corp. and others allied to the oil industry, exhibiting. Between $10,000,000 and $15,000,000 of equipment is estimated to have been sold on the grounds during the exposition. Valuable contacts were made by the exhibitors with key oil men. Attendance passed the 175,000 mark for paid admissions in contrast with 154,000 for the eighth exposition in 1934. Visitors registered from Venezuela, Soviet Russia, India, Germany, Spain, Mexico, England, Canada, France, Colombia, Greece, West Indies, and Rumania. Hotels were overflowed and a housing bureau found rooms in private homes for thousands. Oil companies set up a schedule of shifts in order that as many of their field men might attend as possible. It is said that the companies want a two-weeks' show in 1938 so that more time will be avail-

Jan 1, 1936

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

By C. K. Leith

THE resolution presented at the Annual Meeting of the A.I.M.E., calling on Congress to provide now for postwar accumulation of mineral stock piles under Government control, expresses, I think, the nearly unanimous view of the mining industry. As a result of the trying experiences of the first World War, Mr. Baruch, in his report of Dec. 24, 1919, to the President, urged that steps be taken at once to ensure adequate supplies of raw materials for future emergency. In the twenty years that followed, the same program was vigorously urged on Congress by many individuals and agencies, public and private, including the Secretaries of War and Navy, many members of Congress, the Bureau of Mines, the Planning Committee for Mineral Policy appointed by President Roosevelt, the A.I.M.E., the Mining and Metallurgical Society, and others.

Jan 1, 1943

By Edmund M. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence-the total absence of noise except for one's own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working in the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur.

Jan 1, 1979

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,' the following equation is obtained:

Jan 1, 1962