Search Documents

By CHARLES F. DEISS

The total pipe-line runs of petroleum in Indiana during 1945 were 4,114,000 bbl., a decline of nearly 17 per cent below the estimated 4,950,000 bbl. produced in 1944. Drilling activity during the year was centered in Posey and Gibson Counties, where seven new pools were discovered in the state. Four of the pools are in Posey County-Crunk, Farmersville, Jeffries and St. Wendells East-and the other three are in Gibson County-Johnson West, Lysle and Mt. Carmel East.

Jan 1, 1946

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray 'analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949

IN THE past, we have, perhaps, been somewhat careless in our furnace practice, in the use of high-grade material, lowering the production costs through demanding high-grade ores, increasing the size of units, and eliminating heat losses by collecting and returning unused heat to our furnaces. Further economies would seem to be possible through keeping out of the furnace those materials that appear to serve no useful purpose and carry with them heat that should be used in reduction operations. In the manufacture of pig iron, about three tons of inert nitrogen pass through the furnace for each ton of iron produced. This nitrogen serves no useful purpose in the chemical actions involved, but when discharged into the atmosphere it carries away a considerable quantity of heat. Can not this loss be eliminated, at least in part, through the use of more oxygen in the blast? Many metallurgical chemists, during the past 20 years, have stated that they thought it can and have urged that the plan be tried. Others have expressed doubt, not being able to visualize how more oxygen could be used in present practice; they have regarded it as impracticable, without trying to conceive of an entirely new practice based on a new reagent. That more experimental work has not been done is due to the fact that no cheap oxygen has been available, but the committee believes that there is strong reason to expect that, should a demand exist, 99 per cent. oxygen may be made at a cost not to exceed $3 per ton. The theoretical studies of the committee have indicated such marked economy by using oxygenated air in various operations that its members strongly recommend experimental work to verify the anticipated economies. The committee has developed plans for experimentally determining the effects of oxygen-enriched air on the operation of an iron, blast furnace. A furnace with a height of 30 ft. has been built and it is recommended that the plans be put in, effect as the first step in the research.

Jan 11, 1924

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By M. L. Requa

EVERY forward step in civilization brings with it an increase in population and increasing demand for raw materials. Modern civilization, because of its industrial development, depends more and more for its well-being on ample supplies of raw materials; the higher the type of that civilization, the greater its dependence. No fact is more obvious than that the raw materials should be put to use with greatest prudence and efficiency. National life is not a matter of a decade or a century. Conservation is no longer a matter for political discussion; it is a vital element in the future welfare of all nations. Unfortunately, to the minds of many, conservation means the locking up of natural resources, their arbitrary withdrawal, bringing about, in short, a condition of industrial stagnation. This has occurred in past centuries through misdirected governmental effort. Two eminent engineers have variously defined conservation as follows:

Jan 1, 1925

By Charles H. Behre

KEYNOTE of the mining geology sessions was the preparation for an extensive war with all that this implies as to the need for strategic minerals, both metallic and nonmetallic. Nevertheless the sessions also included many papers of less urgent, more theoretical interest. The stress of wartime production had the effect of giving an unusually full and rich program, the longest in recent years, with sessions continuing virtually throughout the meeting. Some papers dealt with geophysical prospecting as applied to mining geology; others were concerned with the grand strategy of mineral reserves and thus involved the industrial minerals; such "borderline" subjects were presented before sessions held jointly with the Geophysics Committee or the Industrial Minerals Division.

Jan 1, 1942

By H. Vincent Wallace

ALTHOUGH it is universally accepted that free oxygen is A necessary in a cyanide solution for the dissolution of gold and silver-in accordance with Elsner's equation that 2Au + 4KCN + 0 + H20 = 2KAu (CN), + 2KOH- little has been written and insufficient attention paid to the drop in extraction due apparently to loss of dissolved oxygen in mill solutions. Aeration or oxygenation of cyanide solutions has been more or less successfully accomplished by various types of agitators such as the Dorr (with or without air lifts), Pachuca tanks and more recently "Turbo-mixers" and Denver "Super- agitators"; also by the introduction of chemical oxidizing agents such as Solozone (Na,O,) . At the Wright-Hargreaves and other mines in the Kirkland Lake camp, the introduction of this reagent at the rate of about 1.25 oz. per ton of ore applied to the feed of the ball mills has certainly been beneficial.

Jan 1, 1932

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

By L. R. Smith

BUTANE OPERATED drilling rigs are a recent innovation in the petroleum industry, so extensive data on their operation are not available. However, experience indicates that, within limitations, as much can he accomplished with butane as with steam, at a decided reduction .in expense of installation and cost of operation. Commercial butane is a liquid motor fuel similar to gasoline, but much more volatile, so that it has to be stored under pressure. At 10° F. it is liquid at atmospheric pressure, but at 100° it has a pressure of 70 lb. or more. As soon as the pressure is reduced, it turns to vapor and in that state is far more easily mixed with the air necessary for combustion. Butane occurs as a by-product in the absorption process of natural gasoline extraction from casing-head gas. The product has been used to some extent 10 raise the octane value of gasoline. However, because of its volatile nature, such admixture is stable only to a limited degree. Attempts also have been made to introduce the product in a gaseous form into oil- hearing formations in repressuring work. It has, however, until recently, for the most part been wasted.

Jan 1, 1937

By J. David Lowell

For the first time in several years, Chile is again opening its doors to foreign investment. In its new investment code, the Chilean government has announced its willingness to become a partner in joint Chilean-foreign projects for a number of government-controlled porphyry copper deposits at the developed, semi-developed, or prospect stage; and, that it will allow privately owned deposits or deposits discovered by new exploration to be developed with up to 100% foreign ownership. Three deposits of particular interest are: El Abra, with at least 300 million mt of +100% Cu; Los Pelambres, with at least 428 million mt of 0.78% Cu and 0.03% Mo; and Andacollo, with 350 million mt of 0.70% Cu and 0.015% Mo. (El Abra is almost entirely government- controlled; but both Los Pelambres and Andacollo are mostly under private ownership.)

Jan 11, 1974

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By Johnson Crawford, Alan H. Hoagland

Zinc mining at Jefferson City began in 1854 with small scale production of oxidized ore from open pits. Significant production began in 1913 with the development of the Mascot Mine by the American Zinc Company. In 1965, four flotation mills were treating crude ore at the rate of about 12,000 tons per day and the Mascot-Jefferson City district currently is the largest zinc producing area in the United States. The producing mines, Mascot, Young, North Friends Station, New Market Zinc, Grasselli, Davis-Bible, Coy, and the Jefferson City, are 15 to 28 miles northeast of Knoxville in the Valley and Ridge physiographic province, an area of gentle relief lying between the more rugged Great Smoky Mountains and the Cumberland escarpment. The ore is strata bound, occurring essentially within a stratigraphic range of 200 feet in the Lower Kingsport and Upper Longview formations of Lower Ordovician age. In the lower strata of the mineralized section, the ore generally is found in coarsely crystalline elastic dolomite breccia containing silica and chert debris within a sequence of aphanitic limestones. The upper strata of the mineralized section are fine-grained primary dolomites that, in the ore zones, have been fragmented in mosaic patterns by solution collapse with the interfragmental space filled by white gangue dolomite and sphalerite. The mineralogy is unusually simple, sphalerite being the only important sulfide. Pyrite is very sparse. Dolomite gangue is abundant, silica was deposited in quite small amounts, calcite is minor, and fluorite and barite are very rare. The principal ore controlling structures are rubble breccia zones that were formed during the post-Lower Ordovician-pre-Middle Ordovician erosion interval by supergene solution as a phase of the development of a regional karst system of underground drainage that extended to' depths of at least 800 feet. The major Appalachian orogenic structures are post-ore and have been superimposed on the ore bodies. There is substantial evidence to support the current thinking of the writers that the ore deposits were formed at a depth not exc1~eding 800 feet.

Jan 1, 1968

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By George W. Powel

IN the nation's effort to raise its magnesium metal supply to meet the ever increasing demand, the Government is relying not only on standard established practice but has extended its support to developments not so well proved-at least, not commercially proved. Within the past few months considerable progress has been made, not only in the definite output of metal but in the exploitation of new processes, the successful adaptation of which should, in a reasonably short time, assure an adequate supply of magnesium. Recent months have also witnessed a reshuffling of the favored methods as well as of the likely raw materials, with the mineral dolomite gaining in interest over its richer but less abundant competitor, magnesite, while the lowly sea water appears to be losing ground to the higher magnesian brines of Michigan and western Texas. Every month sees a new alignment and there are signs that still newer methods or raw materials will be in use before the industry finally stabilizes itself.

Jan 1, 1942

By R. W. Smith

IN the manufacture of portland cement, the basic and fundamental essential is a limestone uniformly rich in calcium carbonate and carrying less than 3 per cent magnesium carbonate. In searching for such a deposit, also having in mind quantity of rock, accessibility and quarrying facilities, the Pacific Coast Cement Co. discovered and developed its present quarry at View Cove on the east coast of Dall Island, Alaska. Dall Island is about 100 miles west of Ketchikan and 650 miles north from Seattle. It is 70 miles in length and 5 to 10 miles in width. The climatic conditions are much more favorable than would be expected. The temperature ranges from zero to 70 degrees. The precipitation is considerably more than at Seattle, although there was less snow during the last season than at Seattle. The island is rugged and mountainous; the vegetation is moss and grass and a large portion is timbered with spruce, hemlock and cedar. Some of this timber has market value. The limestone quarry is about 30 miles north of the extreme southern end of the island. The company acquired 240 acres which contain limestone of remarkable uniformity, the percentage of calcium carbonate being about 95. It is estimated that there is ample recover- able rock on the holdings to supply the cement plant at its maximum capacity for well over 100 years.

Jan 1, 1929

By Charles H. Morgan

THE case of Henry Cort comprises: (1) the nature of Cort's inventions;, (2) their value to England and to mankind,; (3) the remuneration received therefor by him or his family; and (4) the suitable permanent record and recognition of his services by the representatives of the art lie founded-a debt long over-due, and still unpaid. I. CORT'S INVENTIONS. Under this head, it is unnecessary here to enter into details. The facts have been repeatedly published, and a brief outline of them will be sufficient for my present purpose. . Henry Cort, born in 1740 at Lancaster, England, became a navy broker in. London about 1765, and gained from that business in about ten years. something more than £20,000, which lie devoted to perfecting the manufacture of iron, building a mill at Fontley, near Portsmouth, and prosecuting, between 1777 and 1783, the experiments which culminated in .his two patents, one for puddling iron and the other for shaping it by rolling between grooved rolls.: Careful study of the contemporary evidence, including Cort's specifications, the testimony (in act as well as word) of his business rivals, the public declarations of eminent authorities, and the history of the times, leaves no possible doubt that Cort was the real inventor, of

Mar 1, 1905

By Arthur La Motte

I NDUSTRIAL explosives, as distinguished from military explosives, include high explosives and blasting powder. The high explosives which are best known are straight dynamite, gelatin dynamite, ammonia dynamite and permissibles. There are two kinds of blasting powder, saltpetre blasting powder and nitrate of soda blasting powder. Blasting powders are mechanical mixtures of nitrate of potash or nitrate of soda with sulfur and charcoal, highly compressed, granulated and glazed. They ignite from a spark and burn with relative slowness, the rate of burning and hence the rate of conversion into gases depending upon the size of the granulation and upon the degree of. confinement under which the powder is placed. High explosives, on the other hand, are chemical compounds which detonate; that is, when the explosive is subjected to a violent shock, provided in practice by a blasting cap or an electric blasting cap, the molecule of the essential ingredient, usually nitroglycerin, is disrupted and the energy and heat released cause any other explosive ingredients which may be present, such as ammoniuin nitrate or T.N.T., to decompose with a resultant evolution of gases at an extremely rapid rate varying from 6000 to 20,000 ft. per second.

Jan 1, 1924

By AIME AIME

The Bulletin. As already announced in the January Bulletin, this publication will be issued during the coming year monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates for membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the Institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will be: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. A supplementary session of this meeting will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the further discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. The XCVIIth meeting will be held on the Pacific Coast, including a visit to the Exposition at Seattle, and various other points en route going or coming, depending upon the route and program finally adopted. More definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Feb 1, 1909

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By Morris Cohen, Robert C. Ruhl

The phases in Fe-C alloys over a wide composition range have been studied after splal quenching from the liquid state. Binary alloys containing 0 to 5.1 wt pel C as /cell as a large number of ternary Fe-C-Si alloys with 2.5 to 5.0 wt pct C and 0.3 to 5.1 wt pct Si were attlong those sludied. Olher Fe-C-X alloys, zcilh X being Co, Cr, ,Wn, Ni, and Ru , were also inrestigated after splat quenching. At high carbon contents, a new hcp phase (designaled 6 phase, but different from e carbide) is retained upon splat quenching. The .fraction of this phase varies up lo 97 pcl for a Fe-4.K-1.9% alloy. The composition of the E phase ranges from about 3.8 10 4.8 wt pet C, and the corresponding laltice parameters increase linearly ulith carbon content, while the c/a ratio remains essentially conslc~nl. The E phrtse appears to he a solulion of carbon in E iron, the latler being nornially found only at high pressures. It is deduced that the unit cell of the E phase corresponds to the formula Fe12C3, and llzal il is relaled to tlie ordered slruclures 0.f 6 iron carbide and c iron nilride. The E phase is compared and contrasted to the olher known carbides and nitrides of iron and nickel. An exlrapolaTion of the atomic volume 1,s carhon conlent of /he E pllase lzcts giz.en a neu7 estitnale jor /he alomic volume of E iron, 11.30 cu A, a1 atmospheric pressure and temperature. Other alomic volume relalionships lead to /he co~zpositioti Fe2.iC tor E iron carbide, /he unit cell fortr~ula being -Fe2rClo The E phase undergoes a lulo-slage decomposition upon healing, .forrning firsl rnarlensile plus E carhide, a/ler 1 hr at 140" lo 200°C, slid then ferr ite Plus cementile, after 1 lir a1 330" to 460°C. A1 carbo,l contents between 1.5 and 3.0 LC/ pcl, (he predo.wirzar/t plzase alley quenching is fcc austenite. The retained carbon content of this phase increases with itlcreasing silicon in certain concentration ranges, reaching a maximum of 2.37 wt pct C itz a Fe-2.6C-4.OSi alloy. This is the highest carbon conten1 reLaitled in austenite to date. These high-carbon aus-tenites can be partially tm?zsforttled lo tnartensile hy severe deformation in the temperature range of — 190 to -50°C. TECHNIQUES for splat quenching from the liquid state have been utilized in numerous recent investigations to produce metastable phases in a variety of alloy systems. Among the several ways of splat quenching, the shock-tube method appears to yield the highest cooling rates1-3, 7, 8 and was adopted here. Estimated cooling rates attained in the present experiments ranged from 10' to 10 80Cper sec.' As a part of a research program on interstitial al- loy phases, the Fe-C system was selected for splat-quenching studies. It was hoped that splat quenching would allow high metastable supersaturations of carbon to be retained in solution. Also of considerable interest were the conditions governing the occurrence of the various intermediate phases upon solidification. The alloys investigated included both binary Fe-C compositions as well as six ternary Fe-C-X alloy systems. The known phases in the Fe-C system are summarized in Table I.* Only the ferrite and graphite are ent investigation.14 and is described in detail herein Table II summarizes corresponding data on Fe-N phases, which are also of interest here because of their similarity to the Fe-C phases. EXPERIMENTAL PROCEDURES Alloys were prepared by melting the elements. 99.9 pct purity, in an inert gas nonconsumable electrode arc furnace. The buttons. weighing about 5 g. were remelted twice. were then fragmented. and their interior surfaces were examined for uniformity: if any doubt existed. they were remelted again. Chemical analyses were performed on all the alloys. the accuracy being about k0.05 wt pct. At high temperatures, carbon-containing alloys react with alumina crucibles as follows: If the atmosphere in the splat-quenching furnace does not contain sufficient carbon monoxide the alloy can be depleted of carbon and contaminated with aluminum. Calculations and experimental observations showed that 50 to 100 torr CO partial pressure effectively blocked the above reaction in all the alloys investigated. The splat-quenching equipment in Figs. 1 and 2 provides for evacuation and back-filling with CO-Ar mixtures. The furnace is capable of operation up to 1650°C. and the gettering action of the graphite heating element reduces the oxygen partial pressure in the furnace atmosphere to below 10-5 torr, thus preventing oxidation of the specimens.

Jan 1, 1970