Search Documents

By Forrest T. Moyer

[The safety record of the nonmetal mining industry during 1965 way worse than that of 1961 in all general measures s of injury experience except for a slight improvement in the number and frequency rate of nonfatal injuries Work fatalities in 1965 totaled al and occurred .it a frequencyrate of 0.29 and a severity rate of 1,711 per million man-hours of worktime. The fatality total was seven oven higher than to 1964 and the injury ratess increased d 32 and 28 present, respectively Thin total. of 2,172 nonmetal injuries u- in 1965 was 3.4 less than in 1964 and the frequency rate per million ion man-hours worked declined percent to 22.73 from: 23.14 in 1964. However, the 1965 nonfatal severity rate of 1,339 per million man-hours worked was 15 percent our the: d.96,1 rate of 1,160, This increases was largely attributable to two more permanent total and nine more permanent partial injuries. in 1965 than in the proceeding year. The average severity all injuries in 1965 was 132 days, 1-I. or charged per injury or 25 days more than in 1961. Injury experience in the nonmetal mining industry, including and excluding officeworkers, for the a-year period 1961-65 is shown in table 1. The average number of men working, on active days in 1963 was 48,429, or 635 fewer than in 1961. However, mines and mills, wore active an average: of 5 days more for a total of 277 in 1965, and each worker averaged 2,245 hours compared to 2', 190 hours in 1961. As a result, aggregate worktime of 108.7 million man-hours increased 1 percent over the 1964 total of 107.4 million hours.]

Jan 1, 1970

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By C. M. McCulloch

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°. This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

By P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1945 resulted in the discovery of 23 new fields; one Miocene, eight Frio, three Cockfield-Yegua and eleven along the Wilcox trend. The Wilcox trend appears to he the most active at this time. Producing depths of the new Wilcox discoveries range from 2050 to 10,050 ft. Drilling along the Frio trend has been, for the greater part, projected to the deeper downdip sands. Eighteen of the new discoveries are classified as oil or condensate and five are gas discoveries.

Jan 1, 1946

This report summarizes the results of a research project entitled "Fatal Accident Data Base Development." This project is the last project under Contract No. S0110601. Volumes I and 1I, "Industrial Engineering Study of Hazards Associated with Underground Coat Mine Production," summarize the original industrial engineering project and the Fatal Accident Report Analysis project. These projects were completed and accepted by the U.S. Bureau of Mines on December 10, 1971. Both volumes of the report have been made available by the Bureau to the public through the U. S. Department of Commerce technical information service. Another project under the same con tract, entitled "Equipment Operations Safety Study, ' was completed in January 1972 and the report was accepted by the U. S. B. M. at that time. The analysis in this Natal Accident. Data Lose Development report is closely related to analysis in both of the earlier reports. The original project involved an industrial engineering and safety of production operations for a representative sample of underground bituminous coal mines. The contactor was required to make recommendations 'in work practices, mining methods, equipment, and safety practices which can effectively reduce the fatality rate from rib and roof falls.' (Longwall mining methods were excluded from the study.) Time study and work element analyses were performed in over 50 mines as part of the field data gathering effort. Another requirement of the study was to develop sets of multiflow. Process charts, which are diagrammatic illustrations of the time-related interaction of mining, cycle job elements.

Jan 1, 1972

By Junji Shibata

It is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. In this paper, some examples of the application of solvent extraction to the treatment of wastes are introduced. The treatment of solid wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse water, etching solution and pickling solution are accomplished using solvent extraction technique.

Jan 1, 1996

By Thomas Lane Carter

THE history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development ?of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers ill the mines which the white men started. The Kaffirs of South. Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man's civilization. They are a virile race, and so far the vices of civilization have not killed. them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent-have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribe's in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country, are much finer workmen than the degenerates from less favorable sections: It is universal in South Africa to speak. of the .Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a " boy," and in this paper the word " boy " is synonymous with Kaffir.

Nov 1, 1908

By S Paciornik

Computer-controlled microscopes with digital image acquisition and analysis led to the creation of the new field of digital microscopy. These techniques not only allow a certain degree of automation but have also brought new possibilities to microstructural characterisation. One of these new and promising possibilities is co-site microscopy, which links different kinds of information obtained from different microscopy techniques. The present work presents the development and implementation of a co-site microscopy methodology that combines images obtained by reflected light microscopy (RLM) and scanning electron microscopy (SEM). This methodology can improve the SEM analytical capacity by adding colour information from RLM. It involves the whole sequence, from image acquisition at the microscopes to the analysis of the phases using pattern recognition techniques. An automatic registration procedure for the two kinds of images was developed, allowing the adjustment of magnification, translation, rotation and pixel size, and the correction of local distortions. Thus, the images from RLM and SEM can be combined to build a multidimensional data set of each field, which can then be used in a pattern recognition approach to discriminate different phases. The methodology was tested with a copper ore sample, aiming at the discrimination of minerals that are not distinguishable with either RLM or SEM.

Jan 1, 2008

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By AIME AIME

The first Diesel-electric locomotives for the Mesabi iron range of the Lake Superior district were put into service last summer by the Oliver Iron Mining Co., U. S. Steel subsidiary. There were ten of these locomotives, rated 1000 hp. and weighing 125 tons each. They are designed for service from 16 to 24 hours per day to haul trains of loaded ore cars from open-pit mines, 200 to 400 ft. deep, on a two to eight-mile haul to the top of the pit. The locomotives push or pull the trains over switchbacks and up heavy grades with 5 per cent maximum against the load. High tractive effort, less smoke, and ability to negotiate sharp curves were among the reasons for the selection of Diesel-electric locomotives.

Jan 1, 1941

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

By B. Elevli

This paper deals with the selection of alternative accesses to a podiform chromite orebody in Turkey. The most important alternatives studied in a related project have been stated as a new vertical shaft and a ramp system. The comparison of these alternatives have been carried out on the basis of total investment costs, ore transport unit cost and net present value (NPV) of overall project for various depth. The results show that up to the depth of 700 m, the total investment cost and NPV favours the ramp access while unit ore transport cost make the shaft access preferable.

Jan 1, 2002

By Harry T. Hamilton

THE genial assistant to the president of the New York Trust Co. is the latest addition to the Institute's board of directors, having been elected at the March meeting of the hoard to fill the unexpired term of the late E. E. Ellis. Usually when a banker is appointed to the board of a company the reason is obvious; the difference in this case is that the New York Trust Co. has some of the Institute's money, instead of vice versa. But Harry Hamilton is not really a banker-at least not primarily. Frefluently big financial institutions have a good mining engineer on their staffs to keep them from financing too many "cats and dogs." At any rate Mr. Hamilton gave up his consulting practice in San Francisco back in 1927, to accept his present position in New York. Until then, from the time he graduated from Yale in 1904, lie was constantly engaged in mining operations of one kind or another in the West and in Mexico. His first job was at Christmas, Ariz., where lie did "sampling and miscellaneous work" for the Saddle Mountain Mining Co. The writer tramped up to, all over, and through that property one hog day many years later, when it was run by the Christmas Mining Co., and carp assure the reader that without doubt the young Yale graduate got some good experience and was well broken in. From there Mr. Hamilton went to Cananea for a time, and then to the Copper Queen, at Bisbee, where he was a valued member of the rigging gang. An assignment of assaying and sampling for the Shan¬non Copper Co. at Metcalf lasted for a few months and then he accepted a job for a year with the geological department

Jan 1, 1936

By Rudolf E. Greuer

This report contains a theoretical study on the usefulness of fighting mine fires with inert gases. Four introductory chapters review the role of fires in the mining industry; the conventional fire fighting techniques, the influence of inert gases on the burning of gases and solids, and the well established inert gas fire extinguishing systems for buildings and machinery. A large chapter describes the use which inert gas has found so far for fighting mine fires in major mining countries. More applications have occurred than generally expected and the inert gas method has in the last years become routine in Czechoslovakia and the USSR. This chapter is based on an evaluation of the extensive literature as well as on personal information obtained from leading experts.

Jan 1, 2012

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By W. Chi, R. Regan, R. A. Washington

"In uranium mines, the purification of underground mine air can be accomplished by the removal of dust particles and radon daughters using filters. Full-scale statistically designed experiments with flow rates up to 10,000 cfm have been conducted at Denison Mines Ltd. on mine air filtration with vermiculite as a filter material. Various filtration bed thicknesses were chosen, with different face velocities through each bed thickness. Results on total dust, respirable dust and radon daughter collection efficiencies were analysed statistically. It is shown that these collection efficiencies are directly related to the filter bed thickness. However, the different face velocities seem to affect only the collection of radon daughters. Optimum collection efficiencies for a clean bed of about 30% were found for respirable dust and radon daughters, and about 41>% for total dust, using an 8-in.-thick bed and a face velocity of 500 fpm. Dust build-up on the filter bed during operation led to an increase in collection efficiency, reaching 40 to 60% after two weeks."

Jan 1, 1973