Search Documents

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Kurt Svens

"As zinc consumption is gradually increasing all the time in the world, many zinc plants are looking for possible expansions. As the sulphuric acid market as well as the fertilizer market in many areas is saturated, the costs for the roasting-acid plant section of the zinc plant will create problems when making feasibility calculations for possible expansions. For solving the customers' situation, two proven zinc concentrate direct leaching technologies are available. A third one, which is possible, does not have any industrially proven applications in the zinc area.IntroductionTime to time, the zinc plants in the world scrutinize their operations with respect to their cost efficiency, the total zinc recovery and the near-by or far-away consumer markets, especially the for zinc and sulphuric acid. Their preliminary profitability calculations can show that a possible total expansion is not economical, when they are looking to expand the whole roasting/acid plant - leaching - solution purification - electrowinning - casting route, as the possible market price for the sulphuric acid is low or the sulphuric acid market is too far away. Based on these facts, their economical study often indicates that implementing a zinc concentrate direct leaching option could be more favourable. Regarding this situation, several aspects concerning three alternative direct leaching methods will be discussed, of which pressure leaching and the atmospheric leaching processes have several industrial applications in the zinc industry, as the ultrafine grinding - conventional leaching process at present has none. As iron is also dissolved during zinc concentrate direct leaching, iron removal processes generally used in the zinc industry are additionally discussed below."

Jan 1, 2012

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By Shinya Hodoshima

A catalysis pair of tetralin dehydrogenation / naphthalene hydrogenation has been proposed in the present paper as a liquid organic hydride for operating stationary fuel cells. Catalytic naphthalene hydrogenation, having been commercialized since the 1940s, proceeds to generate decalin via tetralin as an intermediate. The storage capacities of tetralin (3.0 wt%, 28.2 kg-H2 / m3) are lower than decalin (7.3 wt%, 64.8 kg-H2 / m3) but both tetralin dehydrogenation and naphthalene hydrogenation are much faster than the decalin / naphthalene pair. Moreover, existing infrastructures such as gas stations, chemical tankers and tank lorries are available for storage, transportation and supply of hydrogen. With respect to the stationary fuel cells with large space for hydrogen storage, tetralin as a hydrogen carrier is superior to decalin in terms of fast hydrogen supply or power density. Rapid hydrogen supply from tetralin under mild conditions was only accomplished with the carbon-supported metal catalysts in the ?superheated liquid-film states? under reactive distillation conditions. In contrast to the ordinary suspended states, the catalyst layers superheated in the liquid-film state gave high catalytic performances at around 250OC. As a consequence, both serious coke formation over the catalyst surface and excessive consumption of exergy were prevented simultaneously.

Jan 1, 2006

By M. I. Zinigrad

A model of an ideal associated solution is presented. This model takes into account the existence of complexes of various compositions, sizes and geometries and allows calculating thermodynamic properties and phase diagrams of binary alloys. The model has been used formerly to calculate thermodynamic parameters and the position of the liquidus line for binary eutectic systems and also those having a stable compound in the solid phase. In all the cases the model parameters were not adjusted rather estimated from melting temperatures of the components. The recent studies dealt with the influence of arbitrary-stoichiometry associates on the equilibrium thermodynamic properties of liquid alloys. The application of the model to eutectic systems and systems having an unlimited solubility in solid and liquid states close to liquidus has been considered. It was shown that if the difference in melting temperatures of the components was small, different types of fusibility diagrams were possible: eutectic diagrams, cigar-shaped diagrams or diagrams with upper or lower azeotropic points. Peritectic transformations could take place when the difference in melting temperatures of the components was large. The present work is devoted to calculation of phase diagrams and thermodynamic properties of binary systems on the basis of chrome.

Jan 1, 2006

By S. Ikenobu

This paper describes a method for processing high-silicate zinc concentrates by hydrometallurgical zinc refining. Silica in concentrates reacts to form zinc silicate during roasting. The zinc silicate readily dissolves and slowly precipitates in sulfuric acid solutions during leaching. However, if proper operating parameters are not maintained, the colloidal silica may form an unfilterable gel. That is, according to the investigation results obtained, the silica concentration in the reactor has to be maintained at 5 g/1 or less (preferably 2 g/1 or less) by promoting the precipitation reaction. The proposed method has made it possible to precipitate silica in a form having excellent solid-liquid separation characteristics, without the need for facilities having a high filtration capacity, and to maintain a low silica concentration in the reactor by feeding a composition containing pre-adjusted silica contents.

Jan 1, 2000

By M. Dattilo

Research has been conducted over the past three years using the composite anodes versus the lead alloy anodes. The Merrlin composite anodes have shown the improved performance in copper electrowinning versus the lead-calcium-tin anodes. Using the composite anodes a 100-150 mV reduction in anode overpotential has been observed versus the lead alloy anodes in sulfuric acid electrolyte. The composite coating has excellent corrosion inhibiting properties, and reduces or eliminates the formation of manganese oxide scale. Laboratory evidences indicate that, the use of these composite anodes enhances the process of electrowinning by improving the lead alloy corrosion resistance, lowers the electrode potential, reduces the need for cobalt addition, eliminates the anode cleaning, and reduces the generation of acid mist. Field tests are underway.

Jan 1, 1999

By Adam Gesing, Ron Dalton, Richard Wolanski, Larry Berry, Christopher Stewart

As the quantity of aluminum recovered from shredder scrap continues to increase, together with increased content of aluminum in automobiles, so does the economic incentive to further upgrade shredder scrap. This upgrade will be done by sorting and recovering the aluminum by specific usable alloy compositions. The metal recycling industry infrastructure needed to deal with the increased aluminum scrap supply already exists. It is an inverted pyramid structure that in North America comprises: 3000 scrap collection yards, 200 shredders, a dozen sink-float plants and one heavy metal sorting operation. The technology for upgrading aluminum sorted from shredder scrap is already either in industrial use or in the final stages of pilot plant development. However, the current automotive aluminum recycling infrastructure will need to adjust to deal with higher volumes of the metal from aluminum-intensive vehicles that will be appearing in shredder scrap -20 years from now.

Jan 1, 2000

By Rachel De Lucas

Current methods of hydrogen storage are an impediment to the transition of our energy infrastructure from a hydrocarbon to a hydrogen base. The transportation, handling, and storage costs of hydrogen gas account for a majority of its selling price. Magnesium hydride slurry is a safe, environmentally friendly alternative for hydrogen storage. If this form of storage is to be adopted on a large scale, a cost-effective method for recycling the enormous amounts of magnesium hydroxide byproduct must be identified. The solid oxide membrane (SOM) process can be used to recycle the magnesium hydroxide byproduct into magnesium metal, which can be reformed into magnesium hydride and reused for fuel storage. Conventional magnesium extraction/recycling technologies require a great deal of energy and create byproducts that are harmful to the environment and human health. The SOM process poses none of these detrimental effects and requires less energy and feed preparation. The economic viability of a facility that utilizes the solid oxide membrane process for the direct reduction of magnesium must be examined in more detail if industry is to consider it. Cost analysis data related to the commercial viability of a scale-up will be compared to two standard industrial processes: current magnesium production techniques including electrolytic and metallo-thermic processes. We have shown in our cost comparison that the SOM process is cheaper than these traditional techniques and that it is also comparable to aluminum's Hall-Héroult process in cost but with none of the environmentally harmful byproducts.

Jan 1, 2006

By A. V. Tarasov

Regeneration of carbide waste from hard-alloy (sintered carbide) manufacture is an important scientific and technical objective aimed at improving the degree of recycling of rare metals (W, Co, Ta, Ti, Nb). Currently, the degree of recycling of those metals does not exceed 25% to 35% of their total production even in industrially developed countries. This is attributed to a significant extent to the substantial drawbacks of the technologies applied for their processing (environmental pollution, limitations to the use of regenerated products for important applications, sophisticated equipment to be used). An innovative environmentally sound technology has been developed in the Institute of Metallurgy of the Russian Academy of Sciences (IMET RAN) for processing of carbide waste of WC, TiC, TTC and other carbides using asymmetric alternating current of industrial frequency (the electrolyte used for this purpose is nitric acid solution). The current efficiency under optimal conditions is as high as 96% to 98%. The process has been tested on bench scale. The following commercial-grade products are obtained: pure ammonium paratungstate, tungstic acid, cobalt oxide, titanium dioxide and tantalum-niobium concentrate. The total metals recovery is 98% to 99%.

Jan 1, 2006

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By Kang Wan, Lei Tang, Jianchao Li, Jieyu Zhang, Minqi Sheng, Jifang Xu

"The viscous flow phenomenon in slag close to the liquidus temperature was considered. A simple approach that liquidus temperatures of melt could be derived from viscosity data was employed. The potential of this method for estimating the liquidus temperatures of pure water and binary alloy was demonstrated. The liquidus temperatures of the CaO-Alz03 based slags obtained from the second derivative method depends upon the number of viscosity values available at different temperature intervals. The results indicated that plots start deviating from the straight-line behavior at temperature as expect, and the second derivatives show the break points at a certain temperature, which is the liquidus temperature. Comparisons among the present observations as well as the characteristic temperature of the selected slags, which measured by the hemisphere method and DSC, indicated that it is possible to get a reasonable idea of estimate the liquidus temperatures from activation energies for viscous flow.IntroductionThe liquidus temperature of slag, which has a significant effect on the kinetics of chemical reactions and the slag-metal separation, is extremely important for metallurgical operations. Experimental measurements of the liquidus temperatures of slags are difficult, since slags invariable supercool. In addition, behavior of a single constituent in a multi-component slag is different in different circumstances due to its interaction with other constituents. Hence, it is essential to study the liquidus temperature of each particular slag resulting from a special process. Usually, the compositions of the slags aimed to the single liquid region of the phase diagram. However, the phase diagram of many slag systems, which back often to the 1950's, involves considerable uncertainties. Many liquidus temperatures are given as dotted lines in Slag Atlas [1]. Disagreements between the phase diagram and the reality have been found [2]."

Jan 1, 2013

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By Hector M. Lizama

A new technology, known as the HydroZinc? process, is described for the recovery of zinc from sulphide ores that includes heap leaching, neutralization, solvent extraction and electrowinning. Unit operations were scaled up from bench-scale to a 1-t/d zinc cathode demonstration plant. Bench-scale studies defined the process chemistry and a process flowsheet. Column tests were used to design full-scale heaps for zinc bioleaching, and mini-pilot equipment was used to design a solvent extraction circuit. The characteristics of the process required development of a bleed circuit for water and impurities. The complete integrated process was tested on a demonstration plant scale for two years, with about 10 000 t of zinc sulphide ore being bioleached in two 6-m-tall test heaps. In addition to 1 t/d of zinc cathode, iron hydroxide and gypsum residues were produced. The process also generated a small effluent bleed. Over the course of the two-year demonstration test, a number of technical hurdles were overcome and several improvements were made. Some of the more significant ones are presented along with process descriptions and experimental and demonstration plant data. Some engineering aspects and economic evaluations of the new process are also discussed.

Jan 1, 2003

By Maria Cristina Ruiz

The removal of iron from the leaching circuits is a common problem in the hydrometallurgical processing of non ferrous metals. Among the currently available processes, hematite precipitation is the most recommendable from an environmental point of view. This paper is concerned with the batch precipitation of hematite from ferrous sulfate solutions. One of the main objectives of the study was to determine the effect of the experimental conditions on the extent of iron precipitation as well as the purity and the particle size distribution of the precipitates. The main variables studied were temperature (180 to 220 ºC), concentration of sulfuric acid (1 to 10 gpl), initial iron concentration (1 to 15 gpl) and partial pressure of oxygen (3 to 7 atm). The results showed that increasing the oxygen partial pressure from 3 to 7 atm produced a very small increase on the rate of hematite precipitation indicating that a large partial pressure of oxygen is not needed for an effective ferrous to ferric oxidation. An increase in the temperature produced finer precipitates with lower sulfur contents. On the other hand, an increase in sulfuric acid concentration and initial iron concentration produced precipitates with larger particle sizes and higher sulfur contents.

Jan 1, 2006

By M. C. Ruiz

The conventional pyrometallurgical methods to treat copper sulfide concentrates include generally, one or more oxidizing steps where the formation of SO2 gas can not be prevented. From the economical point of view and the nature of some of the processes in which SO2 is produced, its complete capture is not feasible; therefore an important fraction is released to the atmosphere as fugitive emissions. In this research, the reduction of chalcocite was studied in the presence of lime as an alternative method, which overcomes the pollution problems related to SO2 emissions. The effect of temperature, time, concentration of carbon and CaO on the reduction rate were studied. Among these variables, temperature affects most the reduction rate. Conversions over 95 % can be obtained in less that 20 minutes at temperatures over 1000 ° C. The measured partial pressures of the gaseous components indicated that the chalcocite reduction proceeded through the gaseous intermediate species CO, C02, and the overall kinetics was controlled by the Boudouard reaction. The kinetic model In(1-X)= kt fits well the experimental data. Apparent activation energy of 3 14 kJ/mol was calculated for the temperature range of 900 0C-1050 °C.

Jan 1, 1999

By Georgeta Rata, Cornelia Petroman, Ioan Petroman

"Proper training and education in the field of recycling and waste treatment are inconceivable without the proper teaching of the terminology specific to both recycling (aerospace products recycling, automotive recycling, general recycling, recycling behaviour, recycling schemes, recycling systems, and waste recycling) and waste (characterization of waste, electronic waste, heavy-metal containing waste, monitoring of waste, radioactive waste, solid waste, waste collection, waste conversion, waste recycling, waste reutilization, waste stabilization, waste storage, and waste treatment) in both the students’ mother tongue and in English for Special Purposes (ESP) as a second language (with focus on the structuring of the specific terminology). Including linguistic approaches among the possible approaches of environmental protection and material sustainability means including linguistics among the various disciplines addressing energy supply, cement and building materials, metallurgy, chemistry, glassware, pulp and paper industry, machinery, automobile and electronic industries, collection, and sorting, further treatment and final disposal of post-consumer material.IntroductionCultural and technical changes have produced more novel artefacts than novel activities or novel properties, generating new vocabulary needs that are readily answered by new words (nouns).The purpose of this research is to show that ‘waste words’ – phrasal words (items that have the internal structure of phrases but function syntactically as words, e.g., cattle waste) and particularly compound nouns (words formed by combining roots, that tend to have a meaning that is more or less idiosyncratic or unpredictable, e.g., wastepaper ‘discarded paper’) – used in the study of the English of recycling, waste treatment, and clean technologies can be misleading for both native and non-native students and/or users of English because their structure alone does not allow instant, proper understanding of their meaning.Our hypothesis is that this inconvenient can be overcome by getting to reach the proper meaning of these new words. Or, arriving at the precise meanings of the ‘waste words’ depends on our knowledge of the world (for example, wastepaper indicates that some used paper is discarded and not wasted) rather than on purely linguistic knowledge."

Jan 1, 2008

By Dirk Verhulst

The Altair Hydrochloride Pigment Process is a new ?third route?, besides the established high-temperature chloride process and the older sulfate process, to manufacture TiO2 pigment from ilmenite ore. It has been tested at a scale of 5 t/day feed. The ore concentrate is digested in high-acid, high total chloride solution (+/- 39% Cl). Titanium and iron both go into solution. Iron is separated as FeCl2 crystals after reduction and cooling. Titanium is transferred by solvent extraction into a purified, high-Ti stream. It is spray-hydrolyzed to produce a TiO2 hydrate and further calcined with additives into high-quality pigment. HCl solutions generated by pyrohydrolysis and spray hydrolysis are treated by pressure-swing distillation to regenerate HCl gas for re-injection into the digestion reactor. All chloride streams are recycled. Recent work has concentrated on optimization, particularly in 3 areas: - Solvent extraction: a new organic mixture, including a new diluent, makes it possible to work at room temperature, to avoid TiO2 hydrolysis problems and to improve phase disengagement and impurity separation. - Pigment finishing: a systematic study of the parameters involved, followed by long runs in the best conditions confirm pigment quality. - Flow sheet optimization: innovative modifications of the conditions of spray hydrolysis and pyrohydrolysis, combined with re-routing of streams achieve significant energy savings. A 100 t/year pilot plant including these features as well as other process improvements is under construction.

Jan 1, 2006