Search Documents

By Jilai Xue

Oxygen gas bubbles generate on anode during Pb electro-deposition process in PbSiF6-H2SiF6 aqueous solutions at room temperature. Cell voltage varies as the bubbles formed on the anodes surface. The bubble layer on the anode makes a voltage drop that consumes energy in the Pb process, which can be reduced by applying ultrasound on the anode. The effects of ultrasound frequency and anodic current density were investigated with ultrasound on and off, alternatively during the Pb electrode-position process. The removing of the gas bubbles were recorded in association with a drop in the cell voltage. The cell voltage can be lowered by 4% - 6% with ultrasound, which has potential for energy saving in Pb production.

Jan 1, 2010

By N. V. . Panishev

The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.

Jan 1, 2010

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Yongbin Yang

Cathodic reduction of oxygen is a process involved in many fields. As is well known, the mechanism of oxygen reduction usually varies considerably with electrode substrates. In this paper, cathodic reduction of oxygen on gold electrode was studied by linear sweep voltammetry with regards to cyanide leaching of gold. As the results shows, the electron transfer number increases as potential shifted negatively and decreases as pH value increases. Besides, the increment of electron transfer number as a function of potential decreases when pH value increases. When pH increases to 13.0, the volt-ampere curve exhibits a relative flat section with currents approximate to the limit current density of a 2e process. By varying dissolved oxygen concentration, the electron transfer number was calculated for pH11.0 at different potentials, the results being 2.387e, 2.732e, 2.982e, and 3.227e at, -0.35V, -0.40V, -0.45V, and 0.50V, respectively. The calculated current densities are in good conformity with measured results.

Jan 1, 2010

By Svetlana Nikitina

While many question "sustainability" as an intellectual field on the grounds that it is too broad and "undisciplined," we are able to achieve a good balance between breadth of coverage and depth of inquiry in our team-taught seminar "The Grand Challenges: Sustainable Development for the 21st Century" offered to first year students at Worcester Polytechnic Institute. We strike this balance between breadth and depth by a) problematizing key sustainability issues in class discussions; b) by explicitly exploring the lenses of different disciplines (the historical context, the scientific facts, the engineering interventions and the philosophical foundations of unsustainable behaviors); and c) by offering our students opportunities to pursue a targeted project on specific sustainability issues (vertical gardening, metals recycling on college campus) through which they gain depth of understanding as well as practical exposure to all components of the problem, which puts them on the path of seeking effective solutions.

Jan 1, 2010

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By Frank A. Stephens

The process of converting iron ore (principally Fe,03 or Fe30,) into iron carbide (Fe,C) to be used as feedstock for steel-making yields complex mixtures of several Fe-containing compounds as a function of processing conditions. In addition to the above compounds (hematite, magnetite and cementite), the mixtures typically contain wustite (FeO) and metallic iron(Fe). Mossbauer spectroscopy has been developed into aquantitative analytical method for monitoring the degree of conversion to carbide from samples periodically extracted from a fluidized bed reactor type of pilot plant. Calibration of absolute quantities of the above five compounds is based on standards prepared from known mixtures of the high purity individual phases. The PC-based spectrometer allows fitting of the well-known spectral components of each of the five phases, the resulting spectral areas then being compared with the calibration curves via PC software to yield the weight fraction of each. Emphasis has been placed on standardizing and simplifying the analysis procedure for routine use in an industrial environment.

Jan 1, 1993

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits of this approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the SO2 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia:, limonitic ore from New Caledonia and gamieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potenrial followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

By Alexey Lozhko

The technical-and-economic furnace exploitation indices are considerably influenced by the system of heat utilization. In the situation of total output decrease works are forced to exploit furnaces at the partial loading, sometimes even at the idle running for the sake of steam production. The furnace exploitation in this regeme is known to cause the increase of the heat portion, taken away together with waste flue gases. The losses can be partially compensated at the expense of heat exchange efficiency development in the recuperator or heat-exchanger. One of the well-known methods, characterised by high efficiency and low expenditures is the intencification of the heat exchange process by the means of pulsation method.

Jan 1, 2006

By Adriana Gómez

White dross is a result of the aluminum oxidation during its primary production and is mainly composed of metallic aluminum, Al2O3, with minor amounts of AlN and some other oxides. Because of the great variety of phases, the quantitative characterization is complicated. This work shows a quantitative method to determine the main phases of white aluminum drosses by means of X-ray diffraction (the Rietveld method). Nowadays the Rietveld method is maybe the most useful method for obtaining quantitative phases information in multicomponent mixtures, this method permits relatively quick quantitative phase analysis by fitting the calculated X-ray diffraction profile with the observed one. The analysis were done using powder with a grain size less than 45 µm; to obtain the suitable material size the aluminum dross was grounded by ten minutes, several times. The grounded material was screened, and the material smaller than 45 µm was taken to quantitative XRD analysis. Keywords: Rietveld Method, Characterization, Aluminum dross.

Jan 1, 2005

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005

By Dirk van Zyl

As part of the North American regional activities during the Mining, Minerals and Sustainable Development Project (MMSD) one project focused on the development of sustainability evaluations at the operations level. Engagement was identified as one of the seven important questions to be addressed. Engineers and scientists employed in the mining, minerals and materials production arenas must understand the importance of stakeholder engagement, both within and outside the operations as it is essential in the ongoing activities required to contribute to sustainable development. After developing the awareness that a social license can only be contemplated if engagement is in place, they also have to develop skills in engagement processes. This presentation will present the business case for engagement as well as an approach to motivate undergraduate mining engineers to embrace it. The presentation will also review some recent and ongoing research to improve the engagement process.

Jan 1, 2010

By Purushottam Kumar

Keywords: Magnetostriction, magnetic properties, Pd(Fe,Co,Ni) single crystals Fe-Pd, Co-Pd and Ni-Pd alloy systems show appreciable magnetostrictive strains that are of interest for sensor applications. These systems exhibit congruent melting minima. In this work the magnetic and magnetostrictive behavior of congruent melting Fe-Pd, Co-Pd, and Ni-Pd compositions have been examined. The alloys examined include Fe-54.9 at.-% Pd, Ni-45.4 at.-% Pd, and Co-45 at.-% Pd. The paper describes the growth of bulk single crystals of these alloys using Czochralski technique. X-ray diffractometer was used to obtain rocking curves that were used to determine the [001] crystal direction. Magnetostriction in [001] direction was measured using strain gages. Magnetic properties were measured using a vibrating sample magnetometer. Ni-Pd showed the highest magnetostriction values among the congruent melting compositions. Magnetic and magnetostrictive behaviors of these alloy single crystals are presented.

Jan 1, 2005

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005

By Seong- Rin Lim

Light-emitting diodes (LEDs) are regarded as environmentally friendly light sources due to their high energy efficiency and lack of mercury content. LEDs are used for a variety of domestic and commercial lighting systems, where they are replacing incandescent and fluorescent lamps at a rapid rate. Incandescent lamps inefficiently consume energy because electricity is mostly converted to heat rather than light. This causes unnecessary environmental impacts and energy consumption associated with power generation and transmission from a life cycle perspective. Although fluorescent lamps are more energy-efficient than incandescent lamps, their disposal at end-of-life presents special challenges because of the presence of toxic mercury. Despite the seemingly apparent advantages of LED, very few studies have rigorously addressed potential environmental consequences of their disposal. Specifically, LEDs are designed with III-V semiconductors that presumably consist of toxic and rare materials, including arsenic, gallium, and indium. We hypothesize that, depending on their concentrations and leachability, these constituents may also contribute to render LEDs as hazardous waste at the end of their useful life.

Jan 1, 2010

By Yunnen Chen

In the present study, waste materials like pine sawdust and spent grains were investigated to assess their potential for removal of cobalt ion from water by the process of biosorption. The effects of solution pH, reaction time and initial concentration were studied in batch experiments. The removal efficiency of Co(? ) by spent grains was higher than that of pine sawdust. The initial removal was rapid and equilibrium was established in less than 90 min. Equilibrium data all agreed well with both Langmuir and Freundlich isotherm models for the two metal-biomass sorption processes. Good correlation coefficients were obtained for the pseudo second-order kinetic model. Pine sawdust and spent grains were shown to be promising biosorbents for Co(? ) removal from aqueous solutions.

Jan 1, 2010