Search Documents

By Philip E. J. Green

Two of the cornerstones of total quality management, the use of statistical and problem solving tools, and the involvement of employees, are directly applicable to environmental protection. The reduction in variation decreases the chances of violations and mishaps. Involving employees in minimizing environmental impacts is critical. One mistake, even with the best technology, and your plant can be shut down, customers lost and fines and penalties imposed - your reputation and the environment damaged. Proven strategies for involving employees in environmental protection, and over-coming the frequently strong differences of opinions about what constitutes environmental protection, will be discussed.

Jan 1, 1992

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By Xue Wang, Callie Babbitt, Chelsea Bailey, Matt Ganter, Gabrielle Gaustad, Brian Landi

"Current trends, motivated by fossil fuel dependence and unprecedented greenhouse gas (GHG) emissions, show lithium-ion batteries (LIBs) emerging as a competitive energy storage technology due to higher power and energy densities compared to Pb-acid and Ni-metal hydride chemistries. These trends may be of concern, however, as environmental impacts are not well understood for either the LIB itself, or for the nanoparticles consumed or released during the battery's production, use, or end-of-life. This study combines economic modeling, dynamic material flow analysis, and fundamental material characterization methods in order to quantify some of the economic and environmental trade-offs for LIBs at their end-of-life. As expected, results show that as chemistries transition from Li-Co based cathodes to Li based Fe, Mn, and S cathodes, LIB recovery value correlates to the value of the raw materials used. These initial results aim to inform collection policies being proposed currently as well as enable future deployment of novel recycling techniques.IntroductionGlobal fossil fuel dependence and unprecedented GHG emissions have led to increasing attention on energy alternatives, for both electricity production and personal transportation. However, development of renewable energy systems is contingent on concurrent technological development of energy storage systems, primarily batteries used for power grid load-leveling, renewable energy storage, and hybrid and battery electric vehicles. In this sector, lithium-ion batteries (LIBs) are emerging as a competitive technology due to higher power and energy densities compared to lead-acid and nickelmetal hydride chemistries[!]. LIBs represent close to 20% of the total rechargeable battery market and 75% of the portable rechargeable battery market, which is the fastest growing segment of the rechargeable battery market, with a 20% global growth in 2008 [2].This surge in production ofLIBs indicates a looming waste problem; total waste from Li-ion batteries has likely grown substantially from the 500 metric tons estimated in 2003 [3]. Figure IA shows the substantial increase in world-wide lithium production that has occurred in the last several decades with batteries making up the largest share of applications (Figure lB). California and New York state legislators have attempted to proactively address this looming waste by issuing diposal bans on rechargeable batteries in their states[4, 5]. However, quantification of the costs involved in collection, transportation, and processing of these materials has not been examined in depth."

Jan 1, 2012

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators. The current-design offers improved impurity scrubbing along with increased reliability. In addition, a number of alternate gas cleaning systems have been offered. Chematics LAB System: Monsanto DuPont Dynawave System; Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems.

Jan 1, 1992

By P. Louis

Gécamines is the world largest cobalt producer with about 60 % of the Western World production. During the last ten years, its annual production varied from 5,400 to 14,600 t/year. The actual cobalt production capacity of Gécarnines is 18,000 t/year and could be increased in the near future if necessary. Cobalt is presently produced at the Shituru plant by an old in-pulp electrolysis process and in Luilu, by electrolysis of a clear weakly acidic solution. The Shituru Cobalt quality is lower than the Luilu one. For that reason, part of the Shituru Cobalt is fire refined and cast into granules. Large efforts have been succesfully accomplished to improve the cobalt quality. This has been made possible by a better knowledge of the purification processes and of the electrolysis parameters.

Jan 1, 1988

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By Wanderson Silva Rodrigues, Paulo Adão Marinho dos Santos, José Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. This material has no large scale current use and is usually stored. This paper shows that it can be used in a suspension with water as a gas effluent cleaner with high efficiency to remove SO2. It can substitute other materials currently used reducing the overall environmental impact and potentially reducing the cost of gas treatment.2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reuse all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated. In any cases they will remain as an environmental passive and need monitoring for decades. The search of industrial processes that combine the cleaning of gas effluents emission and reuse of these residues can contribute to the reduction of the overall impact of the alumina production process.The main objective of this work is to study the efficiency of the red mud as alternative raw material for the control of emissions of SO2 in combustion gases. Usually this is made through alkaline solutions of CaCO3 or NaOH in absorbing equipments like spray towers or packed column. This project main objective is to study the reaction of the SO2 with a suspension of red mud and water in order to obtain the basic parameters to design equipment capable of process this reaction on a pilot scale. With that goal compositions of red mud on spray were processed with flow of gas containing SO2 with concentration similar to the exhaust gases of the combustion process of the refineries."

Jan 1, 2011

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By Preben Ingerslev

Control of the reheating of ingots is based either on surface temperature measurements using optical pyrometers or on furnace set points and reheat time determined empirically. This paper presents a real-time mathematical heat flow model, named BESTT, which calculates the temperature distribution in an ingot cross section when reheated or cooled. The model runs on a 486 PC in less than one minute for a variety of ingot cross sectional shapes such as circular, square and with some considerations octagonal and heavy-cornered square. Initial temperatures can either be uniform or nonuniform while accounting for temperature dependent thermophysical properties. The model was developed and verified using 718 alloy ingots in box type furnaces. When integrated with on-line pyrometric measurements, BESTT can provide for improved feed back in the reheating control loop. The use of BESlT will assist in reducing energy costs, and improving product quality and consistency. EPD Congress 1994 Edited by C. Warren The Minerals, Metals k Materials Sodety, 1993

Jan 1, 1994

By Sergio N. Monteiro

Lignocellulosic fibers obtained from plants like cotton, flax, hemp, sisal, jute and many others are natural materials used, since long time, in basic items such as textile, baskets, roofing and carpets. These traditional natural fibers as well as some new ones are nowadays replacing synthetic fibers as composite reinforcement owing to environmental advantages. The heterogeneous characteristic of lignocellulosic fibers is, however, a limitation for application in composites. The buriti fiber, extracted from a tropical plant tree, is recently being investigated as a possible reinforcement for polymeric matrix composites but no complete information exists regarding its mechanical behavior. The objective of this work was then to carry out a statistical analysis on the mechanical properties? uniformity of buriti fibers. By precise dimensional measurements in association with tensile tests, it was found that the mechanical properties depend on the range of the fibers? dimension.

Jan 1, 2009

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985

By M Phil Schwarz

"A CFD model for the gas-side of an impinging jet iron bath reactor has been developed to assist in the interpretation and design of oxidizing gas-melt reaction rate experiments. Heat transfer and reaction at the surface have been included. A free surface model, which solves for the liquid motion within the bath as well as the gas motion above the bath, has also been developed. This model also predicts extent and shape of the dimple formed on the liquid surface by the impinging jet. Both models have been run for conditions typical of jet impingement experiments using CO2 , H2O and O2• The main conclusions are• Results from the model for gas-side mass transport are in good agreement with the empirical correlation of Belton and Belton (1980)• Experimentally determined rates of decarburization by CO2 should be corrected for mass transfer because the experiments are often carried out under mixed rate control, eg for gas flow rate 10 L/min when the sulphur concentration is lower than 0.045• If the rate constant for oxygen reaction is greater than about 5 mol/m2.s.atm, it cannot be determined using a gas flow rate of 10 L/min or lower because of mass transfer control.• A cavity of depth 4.5 mm is predicted for a gas flow rate of 10 L/min and this substantially changes the flow field (and hence reaction rate) compared with a simulation in which the surface is assumed to be flat."

Jan 1, 1999

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By A. Ohno

"A new near net shape casting process, OHNO Continuous Casting (OCC), has been recently developed. In this process, molten metal is fed into a heated mold maintained at a temperature above the solidification temperature of the metal being cast. Solidification begins from the central core of the casting rather than the wall of the mold. With the heated mold, the formation of crystals on the mold wall is prevented and solidification occurs out of contact with the mold surface. This produces near net shaped products with smooth, mirror-like surfaces and unidirectional grain structures free from cavities, porosity and segregation. Any crystals formed at the beginning of solidification decrease in number as solidification progresses and eventually a single crystal product is obtained. This process is applicable to any metal alloys, converting them into new materials with superior properties and quality.IntroductionAs a result of growing technical demands for more advanced and diversified materials, the OHNO Continuous Casting (OCC) technology has found many new applications in industry. Considerable interest in the process has been shown in Japan and other countries because of its distinct ability to:produce a single crystal, (1)produce a remarkably clean cast surface without a witness mark,provide extremely good ductility,and reduce casting defects and segregation.This paper provides an overview of the principle of the OCC process and describes the remarkable characteristics of the material produced by this method."

Jan 1, 1988

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By Terry Mandziak

Typical leach mine operations recover gold values through the application of a dilute cyanide solution onto ore within an engineered facility. Key to the success of mining operations is the, containment and management of the cyanide solutions within the facility. Properly engineered' facilities will have containment systems that are both protective of the environment while enhancing solution recovery. This paper not only discusses general containment standards, but identifies state-of-the-art containment and monitoring practices;

Jan 1, 1998