Search Documents

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By I. Perus, M. Fazarinc, G. Kugler, M. Tercelj

"Ledeburitic tool steels are highly alloyed steels used for specific highly loaded applications but are characterized by low and variable hot workability. In this contribution the importance of selecting the right choice of some essential process parameters, i.e. casting temperature, solidification rate and soaking temperature, needed for improving the intrinsic hot deformability of ledeburitic tool steels, is studied. An inappropriate selection of casting temperature and cooling rate results in precipitation of unusual eutectic carbides that decreases the hot workability, whereas with the selection of appropriate soaking temperature the temperature range of safe hot working can be broadened. For each initial as-cast microstructure individually determined soaking temperature should be selected.IntroductionThe surface cracking during hot deformation of ledeburitic tool steels reduces mechanical properties and their industrial yield. These tool steels have high hardness, wear resistance and high tempering resistance on one hand, and high flow stresses and low hot deformability on the other. Decreased hot deformability of the tool steels is attributed to the type, size, shape, distribution, fraction of eutectic carbides and/or other phases, grain growth, etc. at upper limit while precipitation of secondary carbides and decreased recrystallization rate at lower limit of the safe hot deformation temperature range, [1-6].The occurrence of cracks on most exposed areas of workpiece are related to the areas where similar conditions related to upper and/or lower limit of temperature working range prevail, i.e. areas with accelerated cooling, areas with higher value of accumulated strains where also decreased recrystallization rate with simultaneously presence of higher tensile stresses takes place, furthermore areas of workpiece which are due to combustion conditions in furnace heated to higher temperatures, etc. Thus the areas, where combination of previously mentioned conditions prevails, are more exposed to cracking. This additionally requires that hot deformability of ledeburitic tool steel should be considered as a complex problem. Publications in the literature with regards to hot deformability of tool steels are predominately of a partial nature thus all reasons for unexpected occurrence of cracks are not sufficiently explained in available literature so far. Furthermore modern practice proves that previous processing parameters significantly influence the hot deformability and thus this cannot be considered as a constant value. During heating, soaking and hot deformation various processes take place: decay (decomposition) of carbides, formation of new carbides, dissolution of carbides and of alloying elements, etc. Thus depending on variation of process parameters and chemical composition, that consequently influences the processes related to carbides, shifting of decreased deformability at both limits of temperature working range to higher and/or to lower temperatures can occur, [1-14]."

Jan 1, 2012

By Jan Petter Maehlen

Solid H-absorbing materials are in focus of ongoing R&D to offer viable solutions for the hydrogen storage and supply systems aimed on use of hydrogen as energy carrier for automotive transportation. Low operating pressures, combined with high gravimetric and volumetric efficiencies, together with fast kinetics of hydrogen release at ambient temperatures (providing conditions for a low energy loss due to decomposition), are the most important features of the ?ideal? H storage material. Hydrides of the light elements are the only possible candidates to build systems with an overall efficiency similar to those accommodating liquid or compressed (700 bar) hydrogen. One promising material from this point of view is aluminium trihydride, alane AlH3 with a gravimetric storage capacity of 10 wt.% H. This work was focused on studies of the crystal structure and thermal decomposition of alane by application of powder synchrotron X-Ray diffraction.

Jan 1, 2006

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By H. Bai, B. G. Thomas

"A three-dimensional finite difference model has been developed to study the liquid steel-argon bubble two-phase turbulent flow in continuous casting tundish nozzles. Experiments have been performed on a 0.4-scale water model to verify the computational model by comparing its prediction with velocity measurements using PIV (Particle Image Velocimetry) technology. The computational model was developed using CFX and then employed to investigate the effects of various casting process variables. A fast, simple inverse model to quantify relationships between those process variables was developed, based on interpolation of the numerical model results, using Bernoulli's Equation and advanced multivariable curve fitting methods. Predictions using this model compare well with plant measurements. The model has been applied to present trends and observations on the relationship between casting speed, tundish depth, slide gate opening, and argon gas injection rate. The results can also be used to predict .the theoretical steel flow rate through the nozzle, so that clogging conditions can be identified in the plant.IntroductionTundish nozzle geometry is one of the few variables that are both very influential on the casting process and relatively inexpensive to change. Designing an effective nozzle requires quantitative knowledge of the relationship between nozzle geometry and other process variables on the influential characteristics of the flow exiting the nozzle. This relationship depends on the flow pattern within the nozzle components. Most previous modeling studies of flow in the nozzle have focused on single-phase flow [1-4]. Argon injection into nozzle is an efficient and widely employed method to reduce nozzle clogging, even though the real working mechanism(s) are still not fully understood [5]. Argon injection may greatly affect the flow pattern in the nozzle, and subsequently in the mold. Therefore, two-phase flow modeling is needed to improve understanding of fluid flow in the nozzle."

Jan 1, 2000

By P. N. Anyalebechi

"The as-cast microstructure of two commercial-size ingots of aluminum alloy 3004 produced by the electromagnetic casting process was quantitatively characterized. This involved the quantitative determination of through-thickness and across-width variations in dendrite cell size, grain size, macrosegregation of alloying elements, interparticle spacing, and the types, volume fractions, and sizes of the constituent or second phase particles. More than ninety-five percent of the constituent phases in the ingots consisted of the A16(Mn,Fe) phase; the desirable a-Al 12(Fe,Mn)3Si phase was not detected in any of the ingots by Guinier X-ray diffraction analyses or electron probe X-ray microanalyses. A significant microstructural heterogeneity through the thickness and across the width of both ingots was observed. For example, macrosegregation, and the sizes of the constituent phase particles, dendrite cells, and grains increased concomitantly from edge to mid-width and from surface to center of the ingots. There was a -20% depletion (negative macrosegregation) of Mg and a +54-87% enrichment (positive macrosegregation) of Ti in the center of the ingots. With the exception of grain size, there was no significant microstructural difference between the two ingots examined. The causes and practical implications of the observed microstructural heterogeneity in the ingots are discussed.IntroductionThe first step in the fabrication of majority of wrought products of aluminum and its alloys is the casting of large ingots or billets of simple shapes (round or rectangular). The sizes of the ingots vary from 10 mm to 450 mm diameter or 25 mm to 780 mm thick. The quality of the finished products is established at the ingot casting stage. This is because the microstructural characteristics, such as secondary dendrite cell size or arm spacing, amount of alloying elements retained in solid solution, macrosegregation, and the characteristics of second phases, produced during casting cannot be reversed by subsequent processing. Up until twenty-five years ago, the effect of as-cast microstructure of large ingots on the structure and behavior of thin sheets (0.34 mm thick) during drawing and ironing processes was incorrectly assumed to be minimal or nonexistent. This was based on the erroneous notion that the thermal treatments and large reduction (>99.94%) and strain that the ingot undergoes during production of the sheets completely destroys the original ingot structure and its inherent heterogeneity. However, the effects of ingot structure can, a priori, be deduced from the observed effects of constituent phase particle size, type and volume fraction on recrystallization, development of texture during annealing and deformation, and earing. In fact, careful examination of the behavior of products produced from different size ingots or castings have shown that the original microstructure of the ingot has a direct impact on the properties and performance of the end products."

Jan 1, 2011

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By Shen Shen, Paul R. Ohodnicki, Samuel J. Kemion, Vladimir Keylin, Alex Leary, Joseph F. Huth, Michael E. McHenry

"Recent DOE workshops highlight the need for advanced soft magnetic materials leveraged in novel designs of power electronic components and systems for power conditioning and grid integration. Dramatic weight and size reductions are possible in these applications through operating at increased frequencies. This manuscript discusses processing and composition design approaches for optimizing FeCo-based nanocomposites for higher frequency operation at 100 kHz and above. The proposed strategy involves starting with prior compositions known to exhibit high inductions, optimal field crystallization induced anisotropy, and excellent mechanical and high temperature magnetic properties. Proposed alloy modifications for the applications of interest would include increased amorphous phase resistance, optimum induced anisotropy, and minimized or carefully engineered magnetostriction. Relevant process developments would target reduction of ribbon thickness by optimizing the casting process or post-processing treatments such as chemical thinning or rolling. Three archetypes FeCo-based nanocomposites are described including near equiatomic FeCo-based, Fe-rich and Co-rich alloys.MotivationSilicon steels are widely applied for 60Hz utility-scale transformers [1]. For applications at high frequencies, however, Si-steels exhibit unacceptable losses and ferrites are typically used due to their high electrical resistivity and good soft magnetic properties [2]. However, the low inductions offerrites have limited their applications in power electronics. Developments in rapid solidification have led to amorphous metal alloys and controlled nanocrystallization processing has resulted in state-of-the-art amorphous/nanocrystalline nanocomposite soft magnets [3-5]. Commercial utility-scale transformers made with Fe-based amorphous materials have been demonstrated to result in significant energy savings with an associated reduction in greenhouse gas emissions [6]. DOE workshops held in 2010 emphasized a need for advanced soft magnetic materials for the next generation of power electronics. For advanced power conditioning and grid integration applications, frequencies of 20 kHz up to -1 MHz are of interest depending on the power level [7]. Here, we review previous work and discuss the approaches to optimize FeCo-based nanocomposite materials for high frequency applications."

Jan 1, 2012

By Jean Goldschmidt

Recycling of fine oxidized particles of non-ferrous metals usually cannot be carried out by pyrometallurgical methods. 'Hydrometallurgy provides an alternative technology to reintroduce? the resulting products as secondary raw materials into the industrial cycle, thereby saving resources and energy while keeping the environment a little cleaner. The paper summarizes the methods employed by Hydrometal to achieve these objectives and? stigmatizes the latest counterproductive international regulations which create ever more obstacles to environmentally sound recycling.

Jan 1, 1995

By Kazuyuki Kikuta

MMAJ, a govemmental organization in Japan, has carried out a 4 year project for the development of the decontamination and metals recovering technology for the fly ashes from municipal waste incineration. Heavy metals (zinc, lead and copper) are recovered as raw materials for the non-ferrous metals production, without formation of any waste materials to be disposed. More than 500 thousands tonnes a year of fly ashes generation from the municipal waste incineration has been one of the main social issues in Japan, because most of them need to be disposed to the registered areas after decontamination, and occupy 5% of the municipal wastes disposed. The segregation, flotation and chemical process are applied to the treatment of the primary fly ash from municipal waste incineration, and MF (Mitsui-type blast furnace) Process after the chlorine removal to the secondary fly ash. The main results of experiments are -About 90% of heavy metals, zinc, lead and copper, can be recovered from the primary and the secondary fly ashes to the products for the non-ferrous metals production. -Both of the leaching residue from the primary fly ash treatment and the slag from the secondary fly ash treatment can be used as a raw material for the cement production, meaning that the decontamination technology for the ashes without the landfill has been established. -Dioxins in the primary ash can be decomposed satisfactorily, and the dioxins content in the segregation furnace gas is less than O.lng-TEQ/Nm3 without any gas cleaning system

Jan 1, 2003

By Michael L. Free

Bacterial oxidation of an arsenopyritic gold-ore .concentrate was carried out with continuous-flow .operation in 14-liter, mechanically agitated reactors. Samples from the slurry reactors were separated into solid and liquid fractions and analyzed separately to determine the electrochemical rates of sulfide conversion by the bacteria and the rates of direct bacterial oxidation of sulfide. The rates of the individual mechanisms are compared to the overall rates of biooxidation in the continuous-flow slurry reactors. The results show that the commonly hypothesize4 direct and indirect mechanisms of biooxidation both play a significant role in the bacterial oxidation of sulfide ores.

Jan 1, 1991

By M. K. Mohan

During the processing of metals like Cu, Ni, Co, large quantities of solutions, which contain co- products such as Sb, Cd, Pb etc. are generated. These solutions if processed to recover the metals help in conservation of metals as well as environment preservation. The present study was taken up to recover antimony from process solutions using zeolites. The effect of pH of the solution, time and type of zeolite viz., chabazite, mordenite, erionite and clinoptilolite on the sorption of antimony was investigated. Rate of sorption increases with pH and about 77-pct. antimony sorption was observed with chabazite at a pH of 6. Optimal conditions were established for the maximum recovery of antimony fiom process solutions. The mechanism of sorption for Sb was proposed in terms of adsorption and intraparticle diffusion. The calculated adsorption constants from Langmuir and Freundlich equations indicated that the adsorption of antimony on chabazite was strong.

Jan 1, 1999

By G. Diáz

A basic technology coping with a wide range of secondary zinc sources has been developed. The process combines an electrowinning stage, a solvent-extraction unit and a leaching procedure. The acidity generated in zinc electrowinning, transferred by the organic solvent to the aqueous raffinate, is reused to leach the zinc secondary materials. The basic process recovering zinc is described in detail. The route recovering other valuable metals such as copper, cadmium and lead associated with zinc is also described. This non-ferrous metals recovery route is advisable for either ecological and/or economical reasons. Main results of an experimental program aiming at the demonstration of the suitability of the process for several feed materials are summarized. Waelz oxides, galvanizing ashes and EAFD coming from different sources were tested in laboratory and continuous pilot plant campaigns. High zinc recovery, low reagents and utilities consumption, and effluents meeting environmental regulation were confirmed. The paper also includes the main results of a feasibility study of an industrial "base case". A mixed raw material and Spanish EAFD and 20,000 ta of zinc ingots production were chosen. The SGH zinc recovery from secondary raw material by means of the clean, safe and profitable Modified Zincex Process has been demonstrated. This reliable technology is ready for industrial application.

Jan 1, 1995

By Fan Jiang, Haigang Wang, Shi Liu

"This paper describes several applications of Electrical Capacitance Tomography (ECT) in gassolid two phase flows. A new image reconstruction algorithm was evaluated by both simulation and experiments. It is then applied to the online measurement of solids distributions in square circulating fluidized beds (CFBs) and good results were obtained. From the measurement of solids distributions in the bottom zone of a CFB, a bubbly fluidization pattern is identified. A cross-correlation technique was combined with the solids concentration measurements to obtain the flow rate through the dip leg of the cyclone, i.e. the circulating rate of a test CFB. The same· technique was applied in a dense phase pneumatic transport pipe provides the solids concentration, and the flow rate of a wavy gas-solids flow.IntroductionElectrical capacitance tomography (ECT) has been developed for imaging multiphase distributions in the 90's of the ·last century. It is a non-intrusive method. The principle of ECT can be firefly described as follows:Firstly ECT uses a number of electrodes to surround the measuring zone, depicted by Fig. I. The capacitances between the electrodes are measured in turn and an array C is obtained that contains a total number of m independently measured capacitances. Meanwhile the measuring zone is virtually divided into a grid of n pixels, represented by an array G, named the image vector, the gray level of each pixel represents the local value of the concentration of the material. As the material distribution will be reflected by the capacitances between each pair of electrodes, such distributions can be reconstructed according to the measured capacitance, a process called image reconstruction. A common image reconstruction method is called linear-backprojection (LBP). It linearize the relationship between the dielectric distributions in the measuring zone and the capacitances between the electrodes as the following:"

Jan 1, 2004

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By N. A. Vatolin, L. I. Leontjev, S. V. Shavrin

The ever growing interest to the complex iron ores may be attributed to possible production of the naturally alloyed metals and the efficient recovery of the associated elements. However, the conventional technique for complex ore processing is complicated and in some cases even impossible. A pyrometallurgical benefiation of such ores without melted slag formation has been advanced. A version of the technique assumes pellet production with metal coagulated within a slag shell on grinding the pellets, the metal phase is mechanically separated from the slag shell. The technique has been run up with ferro chromo nickel, high-titanium, high-magnesia, alumina phosphorus ores and concentrates. Another version of the pyrometallurgical benefication without melted slag formation in a rotary kiln has been developed from the schemes for processing red mud of alumina manufacture and high-titanium concentrates. Means have been put up to improve schemes available for lex iron ore processing with primary emphasis on material pretreatment before blast furnace and steelmaking processes. Vanadium-bearing titanomagnetite conentrate oxidized pellets possess low strength at reduction. The technique suggested for pelletizing in the controlled atmosphere improves the afore said pellet metallurgical properties. Prodution of metallized pellets in a conveyor roasting machine holds considerable promise for blast furnace and steelmaking processes. In processing the high-sulphur iron ores still another technique is proposed to roast the fluxed pellets with 95% and more desulphuration.

Jan 1, 1988

By Liyuan Chai, Qin Liu, Bing Peng, Jia Wang, Qiang Zhang

"Electrolytic Manganese Residue (EMR) was used as the main material to prepare cementing material activator for the utilization of the residue from electrolytic manganese dioxide (EMD) or electrolytic metallic manganese (EMM) production. The effects of chemical activation, thermal activation and mechanical activation on retarding activity and excitation activity of EMR were investigated according to the setting time and activity index of EMR-slag cementing material. The results showed that the EMR exhibited good activating performance after being ball-milled for 18 min and then treated for 1-2 hours at temperature range of 350-450 ?. The optimal properties of cementing material activator were achieved at the weight percent ratio 30 : 3 : 5 of EMR/Ca(OH)2/cement clinker.IntroductionMany hazardous industrial solid wastes such as blast furnace slag, fly ash, steelmaking slag, chromic slag and electrolytic manganese residue [1] are generated n China and their amounts increases every year. The accumulation of the solid wastes during past years is very huge and they could be hardly recycled effectively as a sustainable resource. 2.35 billion tons of industrial solid wastes have been produced up to now [2]. It is estimated that they would exceed 3.3 billion tons by the end of 2015 [3]. On the other hand, the quick development of Chinese infrastructural construction needs more cementing materials. The production of traditional building materials consumes lots of natural resource such as clay and limestone and discharges at least 1 ton CO2 and other pollutants per ton clinker [4]. Therefore, it is necessary to develop new types of cementing materials instead of clinker [5,6]."

Jan 1, 2012

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012